Tribological Behavior of Graphene Reinforced 600 °C High Temperature Titanium Alloy Matrix Composite

  • Mingyu Wu
  • Guangbao Mi
  • Peijie Li
  • Jianming Cai
  • Chunxiao Cao
Conference paper

Abstract

Graphene reinforced high temperature titanium matrix composite synthesized by spark plasma sintering (SPS) was prepared from mixed powders of graphene oxide (GO) and 600 °C high temperature titanium alloy (TA29). SEM, EDS, XRD, Raman spectroscopy, UMT and SRV tribotester were employed to investigate the microstructure and tribological properties. Microstructural studies indicated that the added graphene oxide was substantially decomposed into graphene during the sintering process and did not cause a significant increase in oxygen content of the TA29 matrix. Graphene was observed to remain after the sintering process and be evenly dispersed in the TA29 matrix. The friction coefficient and wear rate under room temperature and light load were reduced by 15 and 60% respectively, because the graphene dispersed in the matrix was proved to improve the conditions of the frictional interface by self-lubricating effect. The wear rate under high temperature and heavy load was reduced by about 25% for the increasing in the yield strength of graphene reinforced TA29 matrix composite.

Keywords

High temperature titanium alloy Graphene Titanium matrix composite Spark plasma sintering Tribological properties 

Notes

Acknowledgements

This study was financially supported by the National Natural Science Foundation of China (Grant No. 51471155) and Aviation Innovation Foundation of China (Grant No. 2014E62149R).

References

  1. 1.
    C. Leyens, M. Peters, Titanium and titanium alloys: Fundamentals and applications, Weiley-VCH Verlag GmbH & Co. KGaA, Weinheim, 2003.Google Scholar
  2. 2.
    C. Lin, N. Du, Selection and design of titanium alloy, Chemical Industry Press, Beijing, 2014.Google Scholar
  3. 3.
    Y. G. Huang, Developments of titanium and titanium alloy and standardization for surgical implant, Titanium Industry Progress, 27 (2010) 1–8.Google Scholar
  4. 4.
    R.J. Young, I. A. Kinloch, G. Lei, K.S. Novoselov, The mechanics of graphene nanocomposites: A review, Composites Science & Technology, 72 (2012) 1459–1476.Google Scholar
  5. 5.
    C.G. Lee, X.D. Wei, J.W. Kysar, J. Hone, Measurement of the elastic properties and intrinsic strength of monolayer graphene, Science, 321 (2008) 385–396.Google Scholar
  6. 6.
    M. Bastwros, G.Y. Kim, K. Zhang, S. Wang, Fabrication of graphene reinforced aluminum composite by semi-solid processing, ASME 2013 International Mechanical Engineering Congress and Exposition, (2013) V02BT02A030.Google Scholar
  7. 7.
    S.J. Yan, C. Yang, Q.H. Hong, J.Z. Chen, D.B. Liu, S.L. Dai, Research of graphene-reinforced aluminum matrix nanocomposites, Journal of Materials Engineering, 1 (2011) 1–6.Google Scholar
  8. 8.
    B. Hekner, J. Myalski, N. Valle, A. Botor-Probierz, M. Sopicka-Lizer, J. Wieczorek, Friction and wear behavior of Al-SiC(n) hybrid composites with carbon addition, Composites Part B Engineering, 108 (2017) 291–300.Google Scholar
  9. 9.
    J. Hwang, T. Yoon, S.H. Jin, J. Lee, T.S. Kim, S.H. Hong, S. Jeon, Enhanced mechanical properties of graphene/copper nanocomposites using a molecular-level mixing process, Advanced Materials, 25 (2013) 6724–6729.Google Scholar
  10. 10.
    W.J. Kim, T.J. Lee, S.H. Han, Multi-layer graphene/copper composites: Preparation using high-ratio differential speed rolling, microstructure and mechanical properties, Carbon, 69 (2014) 55–65.Google Scholar
  11. 11.
    Q.W. Li, Y. Yang, L.D. Wang, P.Y. Xu, Y.H. Han, Mechanism and kinetics of magnesium sulfite oxidation catalyzed by multiwalled carbon nanotube, Applied Catalysis B Environmental, 203 (2017) 851–858.Google Scholar
  12. 12.
    B.W. Hu, C.C. Huang, X. Li, G.D. Sheng, H. Li, X.M. Ren, J.Y. Ma, J. Wang, Y.Y. Huang, Macroscopic and spectroscopic insights into the mutual interaction of graphene oxide, Cu(II), and Mg/Al layered double hydroxides, Chemical Engineering Journal, 313 (2017) 527–534.Google Scholar
  13. 13.
    C.B. Ji, X.F. Wang, J.W. Zou, J. Yang, Mechanical properties of graphene reinforced nickel-based P/M superalloy, Journal of Materials Engineering, 45 (2017) 1–6.Google Scholar
  14. 14.
    J.M. Cai, G.B. Mi, F. Gao, H. Huang, J.X. Cao, X. Huang, C.X. Cao, Research and development of some advanced high temperature titanium alloys for aero-engine, Journal of Materials Engineering, 44 (2016) 1–10.Google Scholar
  15. 15.
    S.F. Li, B. Sun, H. Imai, T. Mimoto, K. Kondoh, Powder metallurgy titanium metal matrix composites reinforced with carbon nanotubes and graphite, Composites Part A: Applied Science & Manufacturing, 48 (2013) 57–66.Google Scholar
  16. 16.
    Y.Z. Zhang, Dry tribology of the material, Science Press, Beijing, 2012.Google Scholar
  17. 17.
    Y. Song, Y. Chen, W.W. Liu, W.L. Li, Y.G. Wang, D. Zhao, X.B. Liu, Microscopic mechanical properties of titanium composites containing multi-layer graphene nanofillers, Materials & Design, 109 (2016) 256–263.Google Scholar
  18. 18.
    G. Straffelini, A. Molinari, Dry sliding wear of Ti–6Al–4 V alloy as influenced by the counterface and sliding conditions, Wear, 236 (1999) 328–338.Google Scholar
  19. 19.
    F.P. Knudsen, Dependence of mechanical strength of brittle polycrystalline specimens on porosity and grain size, Journal of the American Ceramic Society, 42 (2010) 376–387.Google Scholar
  20. 20.
    X.B. Li, R.T. Liu, S.H. Cheng, M.Y. Li, Tribological behaviors of P/M solid self-lubricating material, Lubrication Engineering, 6 (1999) 53–55.Google Scholar
  21. 21.
    R.Z. Xu, Powder metallurgy structural materials, Central South Industrial University Press, Changsha, 1998.Google Scholar
  22. 22.
    Z.T. Wang, J.S. Meng, Friction wear and wear resistant materials, Harbin Engineering University Press, Harbin, 2013.Google Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2018

Authors and Affiliations

  • Mingyu Wu
    • 1
    • 2
  • Guangbao Mi
    • 1
    • 3
  • Peijie Li
    • 2
  • Jianming Cai
    • 1
  • Chunxiao Cao
    • 1
  1. 1.Aviation Key Laboratory of Science and Technology on Advanced Titanium AlloysAECC Beijing Institute of Aeronautical MaterialsBeijingChina
  2. 2.State Key Laboratory of TribologyTsinghua UniversityBeijingChina
  3. 3.Beijing Engineering Research Center of Graphene and ApplicationBeijingChina

Personalised recommendations