Abstract
An interactive treatment of conditions within the sealing footprint of a soft seal pressed against a relatively rigid wall is presented, based on the assumption of some seepage, however small. This allows the effects of pressure and friction on sealing of O-rings, lip seals, or other forms of soft seals to be analyzed. It has importance for design improvements to sealing effectiveness, extrusion resistance, friction reduction in sliding seals and assessment of the influences of transients or assembly procedures. An example of its application to elastomeric O-rings is given. Other materials, composites and shapes for which an adequate deformation model exists can be treated similarly.
For O-rings, quasi-static finite element analysis has been used previously to calculate deformed shape and total normal reaction load across each sealing footprint. A portion of this normal load is carried by hydraulic pressure of the seepage; the remainder is contact. The hydraulic pressure gradient across a sealing footprint is therefore interactively dependent on the contact pressure distribution according to a relationship that can be found empirically (independently of seal geometry) for particular materials and conditions. This relationship must then be included in the analytical model if hydraulic and contact pressures across the footprint are to be separated, seepage calculated, and friction applied only to the contact component. Otherwise, the pressure-assist and friction behaviour will not be well predicted.
In previous analyses of O-rings it was assumed either that there was no hydraulic pressure in the footprint, or that its gradient was constant. In fact, its gradient will be greatest where the contact pressure is greatest, and least at zero contact (i.e., close to either end of the footprint). An iterative methodology to analyze any relationship between hydraulic pressure gradient and contact pressure is described, and is used in concert with a general purpose finite element code. Linear, power law and exponential cases are compared. Constants or exponents for particular conditions are derived from results for nitrogen leakage between a flat, rubber washer and a rough, metal surface.
Results show the pressure-assist sealing behaviour of a typical O-ring to be less than was previously calculated. Wall friction, however, is also less. For designers, it is shown how such modelling can be used to explore means to improve the behaviour of O-rings and provide a powerful capability for soft seal optimization.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
References
Doubt, G.L., “Reference Book for Design of Valve Packings Sealing High Pressure Water,” AECL Report, AECL-5120, Oct. 1975.
Bazergui, A., Marchand, L. and Payne, J.R., “Effect of Fluid on Sealing Behaviour of Gaskets,” Proc. 10th Int. Conf. on Fluid Sealing. Paper H2, BHRA, Cranfield, April 1984.
George, A.F., Strozzi, A. and Rich, J.I., “Stress Fields in a Compressed Unconstrained Elastomeric ‘0’ Ring Seal and a Comparison of Computer Predictions with Experimental Results,” Proc. 11th Int. Conf on Fluid Sealing. Paper Bl, BHRA, Cranfield, April 1987.
Botto, P., Dragoni, E. and Strozzi, A., “Finite Element Redesign of Reciprocating ‘PTFE’ Rod Seals,” Proc. 13th Int. Conf. on Fluid Sealing. Paper H2, BHRA, Cranfield, April 1992.
Wensel, R.G., Metcalfe, R., Pothier, RE. and Russell, B.G., “O-Ring Seal Studies for Space Shuttle Solid Rocket Booster Joints,” Canadian Aeronautics and Space Institute. Presented at 4th Canadian Symp. on Aerospace Structures and Materials, May 1988.
“MARC General Purpose Finite Element Program-Revision K.3,” (4 volumes), MARC Analysis Research Corporation, Palo Alto, 1988.
Metcalfe, R., Baset, S.B., Lesco, R. and Seiander, W.N., “Modelling of Space Shuttle Solid Rocket O-Rings,” Proc. 12th Int. Conf. on Fluid Sealing. Paper A1 BHRA, Cranfield, May 1989.
Patir, N. and Cheng, H.S., “An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication,” Trans. ASME, J. of Lub. Technology. 100, 2, pp. 12–17, 1978.
Chang, W.R., Etsion, I. and Bogy, D.B., “An Elastic-Plastic Model for the Contact of Rough Surfaces,” Trans. ASME, J. of Trihology. 109, 2, pp. 257–263, 1987.
Nau, B.S., “On the Design of Bolted Gasketed Joints,” Proc. 12th Int. Conf. on Fluid Sealing. Paper D1, BHRA, Cranfield, May 1989.
Author information
Authors and Affiliations
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 1992 Springer Science+Business Media Dordrecht
About this chapter
Cite this chapter
Metcalfe, R., Baset, S.B., Kuran, S. (1992). Contact Hydraulics in The Sealing Footprint — Effects on Deformation, Leakage and Friction of Soft Seals. In: Nau, B.S. (eds) Fluid Sealing. Fluid Mechanics and its Applications, vol 8. Springer, Dordrecht. https://doi.org/10.1007/978-94-011-2412-6_39
Download citation
DOI: https://doi.org/10.1007/978-94-011-2412-6_39
Publisher Name: Springer, Dordrecht
Print ISBN: 978-94-010-5064-7
Online ISBN: 978-94-011-2412-6
eBook Packages: Springer Book Archive