In Lieu of Introduction

  • Natalia I. Obodan
  • Olexandr G. Lebedeyev
  • Vasilii A. Gromov
Part of the Solid Mechanics and Its Applications book series (SMIA, volume 199)


Thin shells are often the best and only choice for designers of flying vehicles, naval vehicles and civil engineering structures. Shell behaviour under a growing load demonstrates its essential nonlinearity, manifesting itself in buckling, in a variety of postbuckling shapes, and in rapid transitions from one shape to another. Nonuniformity of shell structure and loading appeared to be the key factors influencing shell instability (that is the possibility for rapid change of deformed shape, for development of large deflections). The classical Euler approach to stability analysis presumes an ideal undeformed initial state and considers possibility of the solution non-uniqueness in its small vicinity, narrowing the scope of analysis and often delivering improper critical loads. Full nonlinear analysis and its efficient numerical implementation are needed for an investigation of shell behaviour. Typical shell behaviour patterns are studied and the complicated branching of the respective nonlinear boundary problems (including primary, secondary, and tertiary bifurcation paths) are revealed and analyzed. Such important factors as nonuniformity of load and structure (non-symmetric load pattern, structural defects and imperfections, anisotropy, etc.) are to be studied as the causes of initially nonlinear behaviour, transformations of stress-strain state during shell uploading, and a variety of postbuckling forms. Such analysis is performed on the basis of wide-scale numerical analysis. The technical progress of recent decades has placed before designers the paramount task of perceiving complicated loads for structures with minimal structural weight. For aerospace and naval vehicles, as well as civil engineering structures, thin shells, mostly cylindrical and spherical, have been accepted as the best solutions.


Critical Load Cylindrical Panel Subcritical State Civil Engineering Structure Linear Stability Problem 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.


  1. Alinia MM, Habashi HR, Khorram A (2009) Nonlinearity in the postbuckling behaviour of thin steel shear panels. Thin-Walled Struct 47:412–420CrossRefGoogle Scholar
  2. Andreev LV, Obodan NI, Lebedev AG (1988) Ustoichivost obolocheck pri neosesimmetrichnoi deformacii (Shell stability under non-axisymmetric loading). Nauka, MoscowGoogle Scholar
  3. Babich IY, Zhukova NB, Semenyuk NP, Trach VM (2011) Stability of circumferentially corrugated cylindrical shells under external pressure. Int Appl Mech 46(8):919–928MathSciNetCrossRefGoogle Scholar
  4. Barlag S, Rothert H (2002) An idealization concept for the stability analysis of ring-reinforced cylindrical shell. Int J Nonlinear Mech 37(4–5):745–756zbMATHCrossRefGoogle Scholar
  5. Batikha M, Chen JF, Rotter JM, Teng JG (2009) Strengthening metallic cylindrical shells against elephant’s foot buckling with FRP. Thin-Walled Struct 47:1078–1109CrossRefGoogle Scholar
  6. Biagi M, del Medico F (2008) Reliability-based knockdown factors for composite cylindrical shells under axial compression. Thin-Walled Struct 46:1351–1358CrossRefGoogle Scholar
  7. Bielewicz E, Górski J (2002) Shells with random geometric imperfections simulation—based approach. Int J Nonlinear Mech 37(4–5):777–784zbMATHCrossRefGoogle Scholar
  8. Blachut J (2009) Buckling of multilayered metal domes. Thin-Walled Struct 47:1429–1438CrossRefGoogle Scholar
  9. Blachut J (2010) Buckling of axially compressed cylinders with imperfect length. Comput Struct 88:365–374CrossRefGoogle Scholar
  10. Cao QS, Zhao Y (2010) Buckling strength of cylindrical steel tanks under harmonic settlement. Thin-Walled Struct 48:391–400CrossRefGoogle Scholar
  11. Cederbaum G, Touati D (2002) Postbuckling analysis of imperfect nonlinear viscoelastic cylindrical panels. Int J Nonlinear Mech 37(4–5):757–762zbMATHCrossRefGoogle Scholar
  12. Chen L, Rotter JM (2012) Buckling of anchored cylindrical shells of uniform thickness under wind load. Eng Struct 41:199–208CrossRefGoogle Scholar
  13. Chu KH, Turula P (1970) Postbuckling behaviour of open cylindrical shells. J Eng Mech Divisions Proc ASCE 96(6):1142–1151Google Scholar
  14. Degenhardt R, Kling A, Bethge A, Orf J, Karger L, Zimmermann R, Rohwer K, Calvi A (2010) Investigations on imperfection sensitivity and deduction of improved knock-down factors for unstiffened CFRP cylindrical shells. Compos Struct 92:1939–1946CrossRefGoogle Scholar
  15. Dinkler D, Pontow J (2006) A model to evaluate dynamic stability of imperfection sensitive shells. Comp Mech 37(6):523–529zbMATHCrossRefGoogle Scholar
  16. Ewert E, Schweizerhof K, Vielsack P (2006) Measures to judge the sensitivity of thin-walled shells concerning stability under different loading conditions. Comp Mech 37(6):507–522zbMATHCrossRefGoogle Scholar
  17. Fujii F, Noguchi H, Ramm E (2000) Static path jumping to attain postbuckling equilibria of a compressed circular cylinder. Comp Mech 26:259–266zbMATHCrossRefGoogle Scholar
  18. Gavrylenko GD (2003) Numerical and analytical approaches to the stability analysis of imperfect shells. Int Appl Mech 39(9):1029–1045CrossRefGoogle Scholar
  19. Gavrylenko GD (2007) Transformed initial dent as a trigger of the postbuckling process. Thin-Walled Struct 45:840–844CrossRefGoogle Scholar
  20. Goldfeld Y, Vervenne K, Arbocz J, van Keulen F (2005) Multi-fidelity optimization of laminated conical shells for buckling. Struct Multidiscip Optim 30(2):128–141CrossRefGoogle Scholar
  21. Goncalves PB, Silva FMA, Rega G, Lenci S (2011) Global dynamics and integrity of a two-dof model of a parametrically excited cylindrical shell. Nonlinear Dyn 63(1–2):61–82MathSciNetzbMATHCrossRefGoogle Scholar
  22. Grigoluk EI, Lopanicyn EA (2002) Axisymmetric postcritical behaviour of shallow spherical domes. Appl math mech 66(4):621–633Google Scholar
  23. Grigoluk EI, Lopanicyn EA (2003) Non-axisymmetric postcritical behaviour of shallow spherical domes. Appl math mech 67(6):921–932MathSciNetCrossRefGoogle Scholar
  24. Grigorenko YaM, Kas’yan YuB (2001) Deformation of a flexible noncircular long cylindrical shell under a nonuniform load. Int Appl Mech 37(3):346–351MathSciNetCrossRefGoogle Scholar
  25. Gruttmann F, Pham VD (2008) A finite element model for the analysis of buckling driven delaminations of thin films on rigid substrates. Comp Mech 41(3):361–370zbMATHCrossRefGoogle Scholar
  26. Guarracino F, Walker A (2008) Some comments on the numerical analysis of plates and thin-walled structures. Thin-Walled Struct 46:975–980CrossRefGoogle Scholar
  27. Guggenberger W (2006) Elastic stability and imperfection sensitivity of axially loaded cylindrical shells on narrow supports. Comp Mech 37(6):537–550zbMATHCrossRefGoogle Scholar
  28. Hong T, Teng JG (2008) Imperfection sensitivity and postbuckling analysis of elastic shells of revolution. Thin-Walled Struct 46:1338–1350CrossRefGoogle Scholar
  29. Houliara S, Karamanos SA (2010) Stability of long transversely isotropic elastic cylindrical shells under bending. Int J Solid Struct 47:10–24zbMATHCrossRefGoogle Scholar
  30. Huang H, Han Q (2010) Research on nonlinear postbuckling of functionally graded cylindrical shells under radial loads. Compos Struct 92:1352–1357CrossRefGoogle Scholar
  31. Huang H, Han Q, Wei D (2011) Buckling of FGM cylindrical shells subjected to pure bending load. Compos Struct 93:2945–2952CrossRefGoogle Scholar
  32. Huhnea C, Rolfesa R, Breitbachb E, Tebmer J (2008) Robust design of composite cylindrical shells under axial compression—simulation and validation. Thin-Walled Struct 46:947–962CrossRefGoogle Scholar
  33. Hunt G (2006) Buckling in Space and Time. Nonlinear Dyn 43(1–2):29–46zbMATHCrossRefGoogle Scholar
  34. Hunt GW, Lucena Neto E (1993) Maxwell critical loads for axially for axially loaded cylindrical shells. ASME J Appl Mech 60:702–706CrossRefGoogle Scholar
  35. Hunt GW, Peletier MA, Champneys AR, Woods PD, Wadee MA, Budd CJ, Lord GJ (2000) Cellular buckling in long structures. Nonlinear Dyn 21(1):3–29MathSciNetzbMATHCrossRefGoogle Scholar
  36. Hutchinson JW, Koiter WT (1970) Postbuckling theory. Appl Mech Rev 23:795–806Google Scholar
  37. Ishinabea M, Hayashib K (2012) An algorithm for estimating minimum strength of thin-walled structures to resist elastic buckling under pressure. Strength Mater 44(2):205–211CrossRefGoogle Scholar
  38. Jabareen M (2009) Rigorous buckling of laminated cylindrical shells. Thin-Walled Struct 47:233–240CrossRefGoogle Scholar
  39. Jamal M, Elasmar H, Braikat B, Boutyour E, Cochelin B, Damil N, Potier-Ferry M (2000) Bifurcation indicators. Acta Mech 139(1–4):129–142zbMATHCrossRefGoogle Scholar
  40. Jasion P (2009) Stability analysis of shells of revolution under pressure conditions. Thin-Walled Struct 47:311–317CrossRefGoogle Scholar
  41. Junior EP, Silva de Junior AA, Afonso da Silva SMB (2006) Tracing nonlinear equilibrium paths of structures subjected to thermal loading. Comp Mech 38(6):505–520CrossRefGoogle Scholar
  42. Karagiozova D, Zhang XW, Yu TX (2012) Static and dynamic snap-through behaviour of an elastic spherical shell. Acta Mech Sin 28(3):695–710CrossRefGoogle Scholar
  43. Khosravi P, Ganesan R, Sedaghati R (2008) Optimization of thin-walled structures with geometric nonlinearity for maximum critical buckling load using optimality criteria. Thin-Walled Struct 46:1319–1328CrossRefGoogle Scholar
  44. Kim JB, Yang DY (1998) Finite element analysis of the wrinkling initiation and growth in modified Yoshida buckling test. Met Mater Int 4(4):640–647CrossRefGoogle Scholar
  45. Krasovsky VL (1990) Influence of loading scheme on thin-wall cylinders stability for nonuniform axial compression. Int Appl Mech 26(1):38–43Google Scholar
  46. Krasovsky VL, Varyanychko MA (2004) Effect of a “static” resonance in elastic thin-walled cylinders. In: Abstracts book and CD-ROM proceedings of 21st international congress of theoretical and applied mechanics, IPPT PAN, WarsawGoogle Scholar
  47. Kristanic N, Korelc J (2008) Optimization method for the determination of the most unfavorable imperfection of structures. Comp Mech 42(6):859–872zbMATHCrossRefGoogle Scholar
  48. Kumarpanda S, Ramachandra LS (2010) Postbuckling analysis of cross-ply laminated cylindrical shell panels under parabolic mechanical edge loading. Thin-Walled Struct 48:660–667CrossRefGoogle Scholar
  49. Lee MCW, Mikulik Z, Kelly DW, Thomson RS, Degenhardt R (2010) Robust design—a concept for imperfection insensitive composite structures. Compos Struct 92:1469–1477CrossRefGoogle Scholar
  50. Legay A, Combescure A (2002) Efficient algorithms for parametric nonlinear instability analysis. Int J Nonlinear Mech 37(4–5):709–722zbMATHCrossRefGoogle Scholar
  51. Li ZM (2007) Postbuckling of a shear-deformable anisotropic laminated cylindrical shell under external pressure in thermal environments. Mech Compos Mater 43(6):535–560CrossRefGoogle Scholar
  52. Li ZM, Lin ZQ (2010) Nonlinear buckling and postbuckling of shear deformable anisotropic laminated cylindrical shell subjected to varying external pressure loads. Compos Struct 92:553–567CrossRefGoogle Scholar
  53. Li ZM, Zhao YX, Chen XD, Wang WD (2011) Nonlinear buckling and postbuckling of a shear-deformable anisotropic laminated cylindrical panel under axial compression. Mech Compos Mater 46(6):599–626CrossRefGoogle Scholar
  54. Liew KM, Zhao X, Lee YY (2012) Postbuckling responses of functionally graded cylindrical shells under axial compression and thermal loads. Compos B 43:1621–1630CrossRefGoogle Scholar
  55. Lindgaard E, Lund E (2011a) A unified approach to nonlinear buckling optimization of composite structures. Comput Struct 89:357–370CrossRefGoogle Scholar
  56. Lindgaard E, Lund E (2011b) Optimization formulations for the maximum nonlinear buckling load of composite structures. Struct Multidiscip Optim 43(5):631–646CrossRefGoogle Scholar
  57. Lord GJ, Champneys AR, Hunt GW (1999a) Computation of homoclinic orbits in partial differential equations: an application to cylindrical shell buckling. SIAM J Sci Comp 21(2):591–619MathSciNetzbMATHCrossRefGoogle Scholar
  58. Lord GJ, Champneys AR, Hunt GW (1999b) Homoclinic and heteroclinic orbits underlying the postbuckling of axially compressed cylindrical shell. Comp Methods Appl Mech Eng 170:239–251MathSciNetzbMATHCrossRefGoogle Scholar
  59. Lord GJ, Peterhof D, Sanstede B, Sheel A (2000) Numerical computation of solitary waves on infinite cylinders. SIAM J Num Anal 37(5):1420–1454zbMATHCrossRefGoogle Scholar
  60. Luongo A (2010) A unified perturbation approach to static/dynamic coupled instabilities of nonlinear structures. Thin-Walled Struct 48:744–751CrossRefGoogle Scholar
  61. Mang HA, Hofinger G, Jia X (2011) On the interdependency of primary and initial secondary equilibrium paths in sensitivity analysis of elastic structures. Comp Methods Appl Mech Eng 200:1558–1567MathSciNetzbMATHCrossRefGoogle Scholar
  62. Mang HA, Schranz C, Mackenzie-Helnwein P (2006) Conversion from imperfection-sensitive into imperfection-insensitive elastic structures I: Theory. Comp Methods Appl Mech Eng 195:1422–1457MathSciNetzbMATHCrossRefGoogle Scholar
  63. Mathon C, Limam A (2006) Experimental collapse of thin cylindrical shells submitted to internal pressure and pure bending. Thin-Walled Struct 44:39–50CrossRefGoogle Scholar
  64. Nagashima T, Suemasu H (2010) X-FEM analyses of a thin-walled composite shell structure with a delamination. Comput Struct 88:549–557CrossRefGoogle Scholar
  65. Nemeth MP, Young RD, Collins TJ, Starnes JH Jr (2002) Effects of initial geometric imperfections on the nonlinear response of the Space Shuttle superlight weight liquid-oxygen tank. Int J Nonlinear Mech 37(4–5):723–744zbMATHCrossRefGoogle Scholar
  66. Obodan NI, Gromov VA (2006) Numerical analysis of the branching of solutions to nonlinear equations for cylindrical shells. Int Appl Mech 42(1):90–97MathSciNetCrossRefGoogle Scholar
  67. Obodan NI, Gromov VA (2013) Nonlinear behaviour and buckling of cylindrical shells subjected to localized external pressure. J Eng Math 78:239–248CrossRefGoogle Scholar
  68. Obrecht H, Rosenthal B, Fuchs P, Lange S, Marusczyk C (2006) Buckling, postbuckling and imperfection-sensitivity: old questions and some new answers. Comp Mech 37(6):498–506zbMATHCrossRefGoogle Scholar
  69. Ohga M, Wijenayaka AS, Croll JGA (2005) Reduced stiffness buckling of sandwich cylindrical shells under uniform external pressure. Thin-Walled Struct 43:1188–1201CrossRefGoogle Scholar
  70. Ohga M, Wijenayaka AS, Croll JGA (2006) Lower bound buckling strength of axially loaded sandwich cylindrical shell under lateral pressure. Thin-Walled Struct 44:800–807CrossRefGoogle Scholar
  71. Overgaard LCT, Lund E, Camanho PP (2010) A methodology for the structural analysis of composite wind turbine blades under geometric and material induced instabilities. Comput Struct 88:1092–1109CrossRefGoogle Scholar
  72. Papadopoulos V, Charmpis DC, Papadrakakis M (2009) A computationally efficient method for the buckling analysis of shells with stochastic imperfections. Comp Mech 43(5):687–700CrossRefGoogle Scholar
  73. Perret A, Mistou S, Fazzini M (2011) Global behaviour of a composite stiffened panel in buckling. Part 1: numerical modelling. Compos Struct 93:2610–2618CrossRefGoogle Scholar
  74. Perret A, Mistou S, Fazzini M, Brault R (2012) Global behaviour of a composite stiffened panel in buckling. Part 2: experimental investigation. Compos Struct 94:376–385CrossRefGoogle Scholar
  75. Pirrera A, Avitabile D, Weaver PM (2012) On the thermally induced bistability of composite cylindrical shells for morphing structures. Int J Solid Struct 49:685–700CrossRefGoogle Scholar
  76. Polat C, Calayir Y (2010) Nonlinear static and dynamic analysis of shells of revolution. Mech Res Commun 37:205–209CrossRefGoogle Scholar
  77. Prabu B, Raviprakash VA, Venkatraman A (2010) Parametric study on buckling behaviour of dented short carbon steel cylindrical shell subjected to uniform axial compression. Thin-Walled Struct 48:639–649CrossRefGoogle Scholar
  78. Qatu MS, Sullivan RW, Wanga W (2010) Recent research advances on the dynamic analysis of composite shells: 2000–2009. Compos Struct 93:14–31CrossRefGoogle Scholar
  79. Rodriguez J, Merodio J (2011) A new derivation of the bifurcation conditions of inflated cylindrical membranes of elastic material under axial loading. Application to aneurysm formation. Mech Res Commun 38:203–210CrossRefGoogle Scholar
  80. Schenk CA, Schuëller GI (2003) Buckling analysis of cylindrical shells with random geometric imperfections. Int J Nonlinear Mech 38(8):1119–1132zbMATHCrossRefGoogle Scholar
  81. Schneider W (2006) Stimulating Equivalent Geometric Imperfections for the numerical buckling strength verification of axially compressed cylindrical steel shells. Comp Mech 37(6):530–536zbMATHCrossRefGoogle Scholar
  82. Schneider W, Brede A (2005) Consistent equivalent geometric imperfections for the numerical buckling strength verification of cylindrical shells under uniform external pressure. Thin-Walled Struct 43:175–188CrossRefGoogle Scholar
  83. Schneider W, Gettel M (2006) Equivalent geometric imperfections for steel shell structures subject to combined loading. In: III European conference on computational mechanics. Lisbon, Portugal, p 703Google Scholar
  84. Schneider W, Timmel I, Hohn K (2005) The conception of quasi-collapse-affine imperfections: A new approach to unfavourable imperfections of thin-walled shell structures. Thin-Walled Struct 43:1202–1224CrossRefGoogle Scholar
  85. Semenyuk NP, Trach VM (2007) Stability and initial postbuckling behaviour of anisotropic cylindrical shells under external pressure. Int Appl Mech 43(3):314–328MathSciNetCrossRefGoogle Scholar
  86. Semenyuk NP, Trach VM, Zhukova NB (2008) Stability and initial postbuckling behaviour of anisotropic cylindrical shells subject to torsion. Int Appl Mech 44(1):41–60MathSciNetCrossRefGoogle Scholar
  87. Semenyuk NP, Zhukova NB (2011) Stability of compound toroidal shells under external pressure. Int Appl Mech 47(5):545–553CrossRefGoogle Scholar
  88. Shariati M, Rokhi MM (2008) Numerical and experimental investigations on buckling of steel cylindrical shells with elliptical cutout subject to axial compression. Thin-Walled Struct 46:1251–1263CrossRefGoogle Scholar
  89. Shen HS (2010a) Buckling and postbuckling of radially loaded microtubules by nonlocal shear deformable shell model. J Theor Biol 264:386–394CrossRefGoogle Scholar
  90. Shen HS (2010b) Nonlocal shear deformable shell model for postbuckling of axially compressed microtubules embedded in an elastic medium. Biomech Model Mechanobiol 9(3):345–357CrossRefGoogle Scholar
  91. Shkutin LI (2004) Numerical analysis of axisymmetric buckling of a conical shell under radial compression. J Appl Mech Tech Phys 45(5):741–746CrossRefGoogle Scholar
  92. Silvestre N (2007) Generalised beam theory to analyse the buckling behaviour of circular cylindrical shells and tubes. Thin-Walled Struct 45:185–198CrossRefGoogle Scholar
  93. Silvestre N, Gardner L (2011) Elastic local postbuckling of elliptical tubes. J Constr Steel Res 67:281–292CrossRefGoogle Scholar
  94. Singh S, Patel BP, Nath Y (2009) Postbuckling of angle-ply laminated cylindrical shells with meridional curvature. Thin-Walled Struct 47:359–364CrossRefGoogle Scholar
  95. Sosa EM, Godo LA (2009) Challenges in the computation of lower-bound buckling loads. Thin-Walled Struct 47:1078–1091CrossRefGoogle Scholar
  96. van Campen DH, Bouwman VP, Zhang GQ, Zhang J, der Weeme BJ (2002) Semi-analytical stability analysis of doubly curved orthotropic shallow panels—considering the effects of boundary conditions. Int J Nonlinear Mech 37(4–5):659–667zbMATHCrossRefGoogle Scholar
  97. Vaziri A, Estekanchi HE (2006) Buckling of cracked cylindrical thin shells under combined internal pressure and axial compression. Thin-Walled Struct 44:141–151CrossRefGoogle Scholar
  98. Wadee MK, Bassom AP (2000) Restabilization in structures susceptible to localized buckling: an approximate method for the extended postbuckling regime. J Eng Math 38(1):77–90zbMATHCrossRefGoogle Scholar
  99. Walker M, Hamilton R (2005) A methodology for optimally designing fibre-reinforced laminated structures with design variable tolerances for maximum buckling strength. Thin-Walled Struct 43:161–174CrossRefGoogle Scholar
  100. Wang JH, Koizumi A (2010) Buckling of cylindrical shells with longitudinal joints under external pressure. Thin-Walled Struct 48:897–904CrossRefGoogle Scholar
  101. Waszczyszyn Z, Bartczak M (2002) Neural prediction of buckling loads of cylindrical shells with geometrical imperfections. Int J Nonlinear Mech 37(4–5):763–775zbMATHCrossRefGoogle Scholar
  102. Wullschleger L, Meyer-Piening HR (2002) Buckling of geometrically imperfect cylindrical shells—definition of a buckling load. Int J Nonlinear Mech 37(4–5):645–657zbMATHCrossRefGoogle Scholar
  103. Wunderlich W, Albertin U (2002) Buckling behaviour of imperfect spherical shells. Int J Nonlinear Mech 37(4–5):589–604zbMATHCrossRefGoogle Scholar
  104. Yang JH, Guralnick SA (1975) An experimental study of the buckling of open cylindrical shells. Exp Mech 15(4):177–205CrossRefGoogle Scholar
  105. Yi W, Wen-min R, Wei Z (1992) Perturbation formulation of continuation method including limit and bifurcation points. Appl Math Mech 13(9):815–824MathSciNetzbMATHCrossRefGoogle Scholar
  106. Zhang T, Gu W (2012) The secondary buckling and design criterion of composite laminated cylindrical shells. Appl Compos Mater 19(3–4):203–217CrossRefGoogle Scholar
  107. Zhang W, Hisada T, Noguchi H (2000) Postbuckling analysis of shell and membrane structures by dynamic relaxation method. Comp Mech 26:267–272zbMATHCrossRefGoogle Scholar
  108. Zhang X, Han Q (2007) Buckling and postbuckling behaviours of imperfect cylindrical shells subjected to torsion. Thin-Walled Struct 45:1035–1043CrossRefGoogle Scholar
  109. Zhu E, Mandal P, Calladine CR (2002) Buckling of thin cylindrical shells: an attempt to resolve a paradox. Int J Mech Sci 44:1583–1601zbMATHCrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media Dordrecht 2013

Authors and Affiliations

  • Natalia I. Obodan
    • 1
  • Olexandr G. Lebedeyev
    • 2
  • Vasilii A. Gromov
    • 3
  1. 1.Oles Honchar Dnepropetrovsk National UniversityDnepropetrovskUkraine
  2. 2.Atlantis Industrial SystemsDnepropetrovskUkraine
  3. 3.Oles Honchar Dnepropetrovsk National UniversityDnepropetrovskUkraine

Personalised recommendations