Zusammenfassung
Der Wärmeinhalt von Latentwärmespeichern beruht im Wesentlichen auf vier verschiedenen Konzepten [13, 52]. Diese beruhen auf der indirekten Wärmeübertragung mit Rohren und Rippen sowie der direkten Umströmung von makroverkaseltem PCM. Darüber hinaus kann das PCM Bestandteil des Wärmeträgerfluids sein. Speicherausführungen, in denen das PCM direkt in Kontakt zum Wärmeträgerfluid kommt, sind erprobt worden.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Notes
- 1.
Die Bezeichnung von Strecken, Radien und Durchmessern in Geometrien zur Phasenumwandlung ist in der Literatur nicht eindeutig. In vielen Fällen wird Innen und Außen durch Indizierung unterschieden, während Baehr und Stephan den Großbuchstaben R für den äußeren Rohrradius benutzen. Der Radius von PCM-Schichten wird dort nur durch s gekennzeichnet.
- 2.
Die Kepplersche Vermutung, G. Szpiro, Springer (2010).
Literatur
Agyenim, F., Hewitt, N., Eames, P., Smyth, M., A review of materials, heat transfer and phase change problem formulation for latent heat thermal energy storage systems (LHTESS), Renewable and Sustainable Energy Reviews, 14 (2010), S. 615–628
Decken, C., Hantka, H., Binckebank, J. Bachus, K., Bestimmung des Wärmeübergangs von Kugelschüttungen an durchströmendes Gas mit Hilfe der Stoffübergangs-Analogie, Chemie Ingenieur Technik, 32/9 (1960), S. 591–594
Freitag, Thomas, Entwicklung eines Natriumacetat-Trihydrat-Latentwärmespeichers mit einem Wärmeübertrager aus Kunststoffmetallverbund-Kapillarrohr, Dissertation, TU Chemnitz (2005)
Glaser, H., Messung des Wärmeübergangs an Kugelschüttungen nach zwei verschiedenen Verfahren, Chemie Ingenieur Technik, 34/7 (1962), S. 468–472
Goeke, J., Henne, A., Speicherdynamik von Kälte-Speichern mit PCM-Compound Materialfüllung, HLH-Springer, 64/1 (2013), S. 21–26.
Goeke, J., Ruhbach, K., Henne A., Messung der Phasenfrontgeschwindigkeit und der Energiespeicherung von PCM-Compoundmaterialien, HLH-Springer, 61/1 (2010), S. 49–53
Goeke, J., Schwamborn, E., Phasenwechselmaterial in Kugelkapseln, Chemie Ingenieur Technik, 92/8 (2020), S. 1098–1108
Kenisarin, M., Mahkamov M., Costa, S.K., Makhkamova, I., Melting and solidification of PCMs inside a spherical capsule – Review, Journal of Energy Storage, 27 (2020), Article 101082
Kunkel, S., Kübel-Heising, F., Dörnhofer, P., Medina, I., Weis, J., Stabler, R., Repke, J.W., Rädle, M., Direktkontakt-Latentwärmespeicher zur Effizienzsteigerung von Wärmepumpen, Chemie Ingenieur Technik, 90/1–2 (2018), S. 243–240
Kunkel, S., Kübel-Heising, F., Wunder, F., Schreiner, P., Medina, M., Weis, J., Stabler, R., Repke, J., Rädle, M., Vergleich dreier Latentwärmespeicherkonzepte zur effizienten Nutzung von Niedertemperaturwärme, Chemie Ingenieur Technik, 91/1–2, (2019), S. 74–84
Liu, M., Saman, W., Bruno, F., Review on storage materials and thermal performance enhancement techniques for high temperature phase change thermal storage systems, Renewable and Sustainable Energy Reviews, 16 (2012), S. 2118–2132
Lopez-Navarro, A., Biosca-Taronger, J. Corberan, J.M., Penalosa, C., Lazaro, A., Dolado, P., Paya, J., Performance characterization of a PCM storage tank, Applied energy, 119 (2014), S. 151–162
Mehling, H., Cabeza, L.F., Heat and cold storage with PCM, An up to date introduction into basics and applications, Springer, Berlin (2008), ISBN 978-3540685562
Nomura, T., Tsubota, M., Oya T., Okinaka, N., Akiyama T., Heat release performance of direct-contact heat exchanger with erythritol as phase change material, Applied Thermal Engineering, 61/2 (2013), S. 28–35
Nomura, T., Tsubota, M., Oya T., Okinaka, N., Akiyama T., Heat storage in direct-contact heat exchanger with phase change material, Applied Thermal Engineering, 61/2 (2013), S. 28–35, 50/1 (2013), S. 26–34
Petersen, K., LaTherm, Mobile trassenlose Wärmeversorgung, LaTherm GmbH, (2010) https://www.umweltinnovationsprogramm.de/sites/default/files/2019-09/ab_uip_latherm_final_11-11.pdf
Peng, S. Fuchs, A., Wirtz R.A., Polymeric phase change composites for thermal energy storage, J. Appl. Polymer Sci. 93/3, (2004), S. 1240–1251,
Pinnau, S. Strömungs- und kältetechnische Optimierung von Latentkältespeichern, Abschlussbericht, Bundesstiftung Umwelt Az.: 24825, TU Dresden (2009)
Pomianowskia, M., Heiselberg, P., Zhang, Y., Review of thermal energy storage technologies based on PCM application in buildings, Energy and Buildings, 67 (2013), S. 56–69
Rösler, F., Modellierung und Simulation von Phasenwechselvorgängen in makroverkapselten latenten thermischen Speichern, Logos Verlag Berlin (2014)
Soares, N., Costab, J.J., Gasparb, A.R., Santosc, P., Review of passive PCM latent heat thermal energy storage systems towards buildings’ energy efficiency, Energy and Buildings, 59 (2013), S. 82–103
Hybridspeicher
Brunkau, R., Kawasaki, Y., Herzog, E. Wärmetechnisches Verhalten von Latentwärmespeichermaterial, HLH 10, (2015), S. 18–22
Cabeza, L.F., Ibanez, M., Sole, C., Roca, J., Nogue´s, M., Experimentation with a water tank including, a PCM module, Solar Energy Materials & Solar Cells 90 (2006), S. 1273–1282
Liu, M., Saman, W., Bruno, F., Review on storage materials and thermal performance enhancement techniques for high temperature phase change thermal storage systems, Renewable and Sustainable Energy Reviews 16 (2012), S. 2118– 2132
Goeke, J., Henne, A., Büttgen, P., Hybrid-Wärmespeicher mit Wasser und PCM-Granulat, HLH 67/5–6 (2016), Teil 1, S. 18– 22, Teil 2, S. 23–27
Latentwärmespeicher – Wärmeübertragung
Al-Abidia, A., Mat, S., Sopian, K., Sulaimana, M.Y., Mohammad, A., Experimental study of melting and solidification of PCM in a triplex tube heat exchanger with fins, Energy and Buildings, 68 (2014), S. 33–41
Agyenim, F., Hewitt, N., The development of a finned phase change material (PCM) storage system to take advantage of off-peak electricity tariff for improvement in cost of heat pump operation, Energy and Buildings, 42 (2010), S. 1552–1560
Abduljalil A. Al-Abidi, A.A., Mat, S., Sopian, K., Sulaiman, M.Y., Abdulrahman Th. Mohammada Internal and external fin heat transfer enhancement technique for latent heat thermal energy storage in triplex tube heat exchangers, Applied Thermal Engineering, 53 (2013), S. 147–156
Amin, N.A.M., Bruno, F., Belusko, M., Effectiveness–NTU correlation for low temperature PCM encapsulated in spheres, Applied Energy, 93 (2012) S. 549–555
Baby, R., Balaji, C., Experimental investigations on phase change material based finned heat sinks for electronic equipment cooling, International Journal of Heat and Mass Transfer, 55 (2012), S. 1642–1649,
Baehr, H.D., Stephan, K., Wärme- und Stoffübertragung, 7. Auflage, Springer (2010), ISBN 978-3540644583
Cabeza, L.F., Ibanez, M., Sole, C., Roca, J., Nogue’s, M., Experimentation with a water tank including, a PCM module, Solar Energy Materials & Solar Cells 90 (2006) S. 1273–1282
Glück, B., umweltschonende Raumheizung und -kühlung durch multivalenten Einsatz von Kunststoff-Kappilarrohrmatten, BMWI, (2006) Förderkennzeichen: 032 7241 A, B
Goeke, J., Otten, B., Vergleich der konstruktiven Speichertechnik von PCM Wärme-Speichern, HLH-Springer 65/3, (2015), S. 32–39
Goeke, J., Henne, A., Time – Temperature charge function of a high dynamic thermal heat storage with phase change material, Journal of Energy and Power Engineering, (2015), Scientific Research, DOI: https://doi.org/10.4236/epe.2015.72004
Kayansayan, N., Acar, A.M., Ice formation around a finned-tube heat exchanger for cold thermal energy storage, International Journal of Thermal Sciences, 45 (2006), S. 405–418
Khalifa, A., Tan, L., Date, A., Akbarzadeh, A., Maximization of performance of a PCM latent heat storage system with innovative fins, Applied Thermal Engineering, 70 (2014), S. 609–619
Khalifa, A., Tan, L., Date, A., Akbarzadeh, A., Performance of suspended finned heat pipes in high-temperature latent heat thermal energy storage, Applied Thermal Engineering, 81 (2015), S. 242–252
Kozak, Y., Rozenfeld, T., Ziskind, G., Close-contact melting in vertical annular enclosures with a non-isothermal base: Theoretical modeling and application to thermal storage, International Journal of Heat and Mass Transfer, 72 (2014), S. 114–127
Ismail, K.A.R., Lino, F.A.M., Fins and turbulence promoters for heat transfer enhancement in latent heat storage systems, Experimental Thermal and Fluid Science, 35 (2011), S. 1010–1018
Laing, D., Bauer, T., Steinmann, W.D., Lehmann, D., Advanced high temperature heat storage System – Design and Results, 11th International Conference on Thermal Energy Storage – Effstock 14–17 June (2009)
Lipinski, T., Jouharaa, H., Zabnienska-Goraa, A., Khordehgaha, N., Ahmada, D, Latent thermal energy storage technologies and applications – A Review, International Journal of Thermofluids 5/6 (2020), A. 100039
Liu, C., Groulx, D., Experimental study of the phase change heat transfer inside a horizontal cylindrical latent heat energy storage system, International Journal of Thermal Sciences, Vol. 82 (2014), S. 100–110
Philippen, D., Logie, W., Thalmann, M., Haller, M., Brunold, S., Frank, E., Development of a heat exchanger that can be deiced for the use in ice stores in solar thermal heat pump systems, EuroSun 2012, ISES Europe Solar Conference, (2012) Rijeka
Rathore, P.K.S., Shukla, S.S., Potential of macroencapsulated PCM for thermal energy storage in buildings: A comprehensive review, , Construction and Building Materials, Volume 225, (2019), S. 723–744
Sciacovelli, F. Gagliardi, V. Verda, A numerical and experimental study of solidification around axially finned heat pipes for high temperature latent heat thermal energy storage units, Applied Energy 137 (2015), S. 707–715
Sridharan, S., Srikanth, R., Balaji, C., Multi objective geometric optimization of phase change material based cylindrical heat sinks with internal stem and radial fins, Thermal Science and Engineering Progress, 5 , (2018), S. 238–251
Tan, F.L., Hosseinizadeh, S.F, Khodadadi, J.M., Liwu Fan, Experimental and computational study of constrained melting of phase change materials (PCM) inside a spherical capsule, International Journal of Heat and Mass Transfer 52 (2009), S. 3464–3472
Tay, N.H.S., Bruno, F., Belusko, M., Experimental validation of a CFD and an e-NTU model for a large tube-in-tank PCM-System, International Journal of Heat and Mass Transfer 55 (2012), S. 5931–5940
Schaumann, G., Wärmenutzug mit dem Transheat-System, Landesforstverwaltung Rheinlandpfalz, Projektbericht (TSB-Energie) Nr.: 575 (2001)
Zalba B., Marin J.M., Cabeza L.F., Mehling H., Review on thermal energy storage with phase change materials, heat transfer analysis and applications. Applied thermal Engineering, 23 (2003), S. 251 – 283
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 2021 Der/die Autor(en), exklusiv lizenziert durch Springer Fachmedien Wiesbaden GmbH, ein Teil von Springer Nature
About this chapter
Cite this chapter
Goeke, J. (2021). Thermische Speicher mit Phasenwechselmaterial. In: Thermische Energiespeicher in der Gebäudetechnik. Springer Vieweg, Wiesbaden. https://doi.org/10.1007/978-3-658-34510-5_11
Download citation
DOI: https://doi.org/10.1007/978-3-658-34510-5_11
Published:
Publisher Name: Springer Vieweg, Wiesbaden
Print ISBN: 978-3-658-34509-9
Online ISBN: 978-3-658-34510-5
eBook Packages: Computer Science and Engineering (German Language)