Abstract
This chapter deals with several typical solutions to demonstrate effects of the mis-match factor, three-dimensional deformation (thickness effect) and plastic anisotropy on the limit load of welded plates. The general approach to build up singular kinematically admissible velocity fields previously used in plane strain and axisymmetric solutions for highly undermatched structures is extended to three-dimensional deformation of tensile specimens to estimate the thickness effect on the limit load. The effect of the mis-match factor on the limit load is illustrated by simple examples for overmatched and undermatched center cracked specimens in tension. The effect of plastic anisotropy on the limit load is demonstrated for both highly undermatched and overmatched center cracked specimens under plane strain conditions.
This is a preview of subscription content, log in via an institution.
Buying options
Tax calculation will be finalised at checkout
Purchases are for personal use only
Learn about institutional subscriptionsReferences
S.E. Aleksandrov, R.V. Goldstein, Influence of plastic anisotropy on predictions of some engineering approaches in fracture mechanics. Mech. Solids 46, 856–862 (2011)
S. Alexandrov, A note on the limit load of welded joints of a rectangular cross - section. Fat. Fract. Eng. Mater. Struct. 22, 449–452 (1999)
S. Alexandrov, Specific features of solving the problem of compression of an orthotropic plastic material between rotating plates. J. Appl. Mech. Technol. Phys. 50, 886–890 (2009)
S. Alexandrov, Effect of plastic anisotropy on the predictive capacity of flaw assessment procedures. Mater. Sci. Forum 638–642, 3821–3826 (2010a)
S. Alexandrov An effect of plastic anisotropy on the strain rate intensity factor. in Proceedings 10th biennial ASME conference on engineering systems design and analysis (ESDA 2010), Istanbul (Turkey), 12–14 July 2010, Paper ESDA2010-24021 (2010b)
S. Alexandrov, Behavior of anisotropic plastic solutions in the vicinity of maximum-friction surfaces. J. Appl. Mech. Technol. Phys. 52, 483–490 (2011)
S. Alexandrov, N. Chikanova, M. Kocak, Analytical yield load solution for overmatched center cracked tension weld specimen. Eng. Fract. Mech. 64, 383–399 (1999)
S. Alexandrov, K.-H. Chung, K. Chung, Effect of plastic anisotropy of weld on limit load of undermatched middle cracked tension specimens. Fat. Fract. Eng. Mater. Struct. 30, 333–341 (2007)
S.E. Alexandrov, R.V. Goldstein, An upper bound limit load for overmatched scarf-joint specimens. Fat. Fract. Eng. Mater. Struct. 22, 975–979 (1999)
S. Alexandrov, Y.-M. Hwang, A limit load solution for highly weld strength undermatched DE(T) specimens. Eng. Fract. Mech. 77, 2906–2911 (2010)
S. Alexandrov, M. Kocak, Effect of three-dimensional deformation on the limit load of highly weld strength undermatched specimens under tension. Proc. IMechE Part C: J. Mech. Eng. Sci. 222, 107–115 (2008)
S. Alexandrov, N. Kontchakova, Influence of anisotropy on limit load of weld-strength overmatched cracked plates in pure bending. Mater. Sci. Eng. 387–389A, 395–398 (2004)
S. Alexandrov, N. Kontchakova, Influence of anisotropy on the limit load of a bi-material welded cracked joints subject to tension. Eng. Fract. Mech. 72, 151–157 (2005)
S. Alexandrov, G.-Y. Tzou, Influence of plastic anisotropy on limit load of welded joints with cracks. Key Eng. Mater. 345–346, 425–428 (2007)
S. Alexandrov, G.-Y. Tzou, S.-Y. Hsia, Effect of plastic anisotropy on the limit load of highly undermatched welded specimens in bending. Eng. Fract. Mech. 75, 3131–3140 (2008)
A. Capsoni, L. Corradi, P. Vena, Limit analysis of orthotropic structures based on Hill’s yield condition. Int. J. Solids Struct. 38, 3945–3963 (2001a)
A. Capsoni, L. Corradi, P. Vena, Limit analysis of anisotropic structures based on the kinematic theorem. Int. J. Plast. 17, 1531–1549 (2001b)
K.S. Chan, Effects of plastic anisotropy and yield surface shape on sheet metal stretchability. Metall. Trans. 16A, 629–639 (1985)
J.C. Gibbings, Dimensional Analysis (Springer, London, 2011)
I.F. Collins, S.A. Meguid, On the influence of hardening and anisotropy on the plane-strain compression of thin metal strip. Trans. ASME J. Appl. Mech. 44, 271–278 (1977)
R. Hill, The Mathematical Theory of Plasticity (Clarendon Press, Oxford, 1950)
J. Joch, R.A. Ainsworth, T.H. Hyde, Limit load and J-estimates for idealised problems of deeply cracked welded joints in plane-strain bending and tension. Fat. Fract. Eng. Mater. Struct. 16, 1061–1079 (1993)
Y.-J. Kim, K.-H. Schwalbe, Compendium of yield load solutions for strength mis-matched DE(T), SE(B) and C(T) specimens. Eng. Fract. Mech. 68, 1137–1151 (2001)
A. Kotousov, M.F.M. Jaffar, Collapse load for a crack in a plate with a mismatched welded joint. Eng. Failure. Anal. 13, 1065–1075 (2006)
J.R. Rice, Plane strain slip line theory for anisotropic rigid/plastic materials. J. Mech. Phys. Solids 21, 63–74 (1973)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2012 The Author(s)
About this chapter
Cite this chapter
Alexandrov, S. (2012). Miscellaneous Topics. In: Upper Bound Limit Load Solutions for Welded Joints with Cracks. SpringerBriefs in Applied Sciences and Technology(). Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-642-29234-7_6
Download citation
DOI: https://doi.org/10.1007/978-3-642-29234-7_6
Published:
Publisher Name: Springer, Berlin, Heidelberg
Print ISBN: 978-3-642-29233-0
Online ISBN: 978-3-642-29234-7
eBook Packages: EngineeringEngineering (R0)