Abstract
Offshore steels for the arctic conditions have an increasing demand due to the opening of new oil fields in the Arctic Ocean. However, the requirements for these steels are extremely demanding, as they need to maintain the desired properties in harsh arctic conditions. Additionally, these requirements need to be achieved also in heat-affected zones caused by the welding. In this study the heat-affected zones were created using the physical simulation, so that the zones would be wide enough for reliable mechanical testing.
Continuous cast 500 MPa offshore steel was hot rolled in the laboratory hot rolling mill to find out the mechanical properties of the base metal. The physically simulated heat-affected zones were studied using Gleeble 3800. Two different cooling times from 800°C to 500°C (t8/5) were used in order to simulate two different welding methods with different heat inputs. Microstructure of both base materials and simulated heat-affected zones were studied using scanning electron microscope and laser scanning confocal microscope. Charpy V-notch impact toughness and hardness profiles were determined of both base material and simulated heat-affected zones.
The base metal microstructure was ferritic with some lath-like bainitic features. Minor changes were noted in the microstructure of physically simulated inter-critical heat-affected zone (ICHAZ), while in physically simulated coarse grained heat-affected zone (CGHAZ) the prior austenite grains had coarsened and the transformation microstructure consisted of lath-like features of bainite and in case of a shorter t8/5 of 6 s, even martensite. It was found out that the critical location regarding the impact toughness in arctic temperatures was found out to be CGHAZ, while the impact toughness of ICHAZ did not differ remarkably from that of the base material. The CGHAZ impact toughness was weaker with t8/5 = 30 s than with t8/5 = 6 s indicating that lower heat input welding methods are more beneficial for this material.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Gáspár, M., Balogh, A., Sas, I.: Physical simulation aided process optimisation aimed sufficient HAZ toughness for quenched and tempered AHSS. In: IIW International Conference on High-Strength Materials - Challenges Application, IIW, Helsinki, Finland (2015)
Lee, S.G., Lee, D.H., Sohn, S.S., Kim, W.G., Um, K.-K., Kim, K.-S., Lee, S.: Effects of Ni and Mn addition on critical crack tip opening displacement (CTOD) of weld-simulated heat-affected zones of three high-strength low-alloy (HSLA) steels. Mater. Sci. Eng., A 697, 55–65 (2017). https://doi.org/10.1016/j.msea.2017.04.115
Laitinen, R., Porter, D.A., Karjalainen, L.P., Leiviskä, P., Kömi, J.: Physical simulation for evaluating heat-affected zone toughness of high and ultra-high strength steels. Mater. Sci. Forum 762, 711–716 (2013). https://doi.org/10.4028/www.scientific.net/MSF.762.711
Heikkilä, S.J., Porter, D.A., Karjalainen, L.P., Laitinen, R.O., Tihinen, S.A., Suikkanen, P.P.: Hardness profiles of quenched steel heat affected zones. Phys. Numer. Simul. Mater. Process. Vii. 762, 722–727 (2013). https://doi.org/10.4028/www.scientific.net/MSF.762.722
Graville, B.A.: Cold Cracking in Welds in HSLA Steels. Iin: Weld. HSLA Struct. Steels, AIM/ASM, Rome, Italy (1976)
Rykalin, N.N.: Calculations Concerned with Thermal Processes in Welding. Mashgiz, Moscow (1951)
Martinez, E.L., Vázguez-Gómez, O., Vergara-Hernández, H.J., Serna, S., Campillo, B.: Mechanical characterization of the welding of two experimental HSLA steels by microhardness and nanoindentation tests. Met. Steels Int. 22, 987–994 (2016)
Zhang, L., Kannengiesser, T.: HAZ softening in Nb-, Ti- and Ti + V -bearing quenched and tempered steels. Weld. World 60, 177–184 (2016)
EN 10225, Weldable Structural Steels for Fixed Offshore Structures. Technical Delivery Conditions, Suomen standardoimisliitto (2009)
Robinson, I.D.G.: Grain growth and austenite decomposition in two Niobium containing line pipe steels. The University of British Columbia (2016). https://doi.org/10.14288/1.0308782
Ghosh, A., Ray, A., Chakrabarti, D., Davis, C.L.: Cleavage initiation in steel: competition between large grains and large particles. Mater. Sci. Eng., A 561, 126–135 (2013). https://doi.org/10.1016/j.msea.2012.11.019
Mourujärvi, J., Tihinen, S., Mehtonen, S., Lahtinen, T., Vilaca, P., Kaijalainen, A., Porter, D., Kömi, J.: Effect of Titanium on the Weldability of thermomechanically rolled high-strength cold-formable steels. In: Proceedings Metallurgy 2017 - 26th International Conference on Metallurgy and Materials, Brno, Czech Republic (2017)
Acknowledgement
The authors are grateful to the Finnish Funding Agency for Technology and Innovation (Tekes) for financing this work as a part of the research project FLEX – Flexible and Adaptive Operations in Metal Production. We would also like to thank the staff of the Research Center of SSAB Europe Oy Raahe for valuable cooperation.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer International Publishing AG, part of Springer Nature
About this paper
Cite this paper
Tervo, H., Mourujärvi, J., Kaijalainen, A., Kömi, J. (2018). Mechanical Properties in the Physically Simulated Heat-Affected Zones of 500 MPa Offshore Steel for Arctic Conditions. In: Jármai, K., Bolló, B. (eds) Vehicle and Automotive Engineering 2. VAE 2018. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-319-75677-6_66
Download citation
DOI: https://doi.org/10.1007/978-3-319-75677-6_66
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-75676-9
Online ISBN: 978-3-319-75677-6
eBook Packages: EngineeringEngineering (R0)