Advertisement

Analysis for Sensitivities of the Mould Stiffness and Heat Transfer Design Result to the Mould Structure Design Parameters

  • Fengyang BiEmail author
  • Bo Yang
  • Tianguo Jin
  • Changxi Liu
  • Xiaohong Wang
Conference paper
Part of the Advances in Intelligent Systems and Computing book series (AISC, volume 691)

Abstract

Sensitivities of the mould stiffness and heat transfer design result to the mould structure design parameters were analyzed. Based on the parameters of the mould structure design, the temperature difference of the mould surface should be reduced, the stiffness of the mould be increased, and the mass of the mould should be reduced as much as possible. In the process of designing, proper thickness of molded surface is of most importance, then come proper numbers and sizes of air vent.

Keywords

Mould structure design parameters Sensitivities of the mould Mould stiffness Mould heat transfer 

Notes

Acknowledgments

This research was supported by the National Natural Science Foundation of China (no. 51575139, 51605057), Natural Science Foundation of Heilongjiang Province (no. E2015027), China Postdoctoral Science Foundation (no. 2016M600721), Special Financial Aid to Post-doctor Research Project of Chongqing (no. Xm2016058), Fundamental and Frontier Research Project of Chongqing (no. cstc2016jcyjA0456), Self-Planned Task of State Key Laboratory of Mechanical Transmission (no. SKLMT-ZZKT-2016Z04), Project of Innovative Talents Foundation of Harbin City (no. 2016RAQXJ075, 2016QN001011,2016QN017023), Project of Doctor Foundation of Heilongjiang Institute of Technology (no. 2015BJ07). Their support is gratefully acknowledged.

References

  1. 1.
    Du, S.: Advanced composite materials and aerospace engineering. Acta Mater. Compos. Sin. 24(01), 1–12 (2007)Google Scholar
  2. 2.
    Yang, N.: Composite structures for new generation large commercial jet. Acta Aeronau. Tica Et Astronau. Tica Sin. 29(3), 596–604 (2008)Google Scholar
  3. 3.
    Stefaniak, E.K., Spröwitz, T., Hühne, C.: Experimental identification of process parameters inducing warpage of autoclave-processed CFRP parts. Compos. Part A 43(7), 1081–1091 (2012)CrossRefGoogle Scholar
  4. 4.
    Kappel, E., Stefaniak, D., Holzhüter, D., Hühne, C., Sinapius, M.: Manufacturing distortions of a CFRP box-structure A semi-numerical prediction approach. Compos. Part A 51(8), 89–98 (2013)CrossRefGoogle Scholar
  5. 5.
    Kappel, E., Stefaniak, D., Spröwitz, T., Hühne, C.: A semi-analytical simulation strategy and its application to warpage of autoclave processed CFRP parts. Compos. Part A 42(12), 1985–1994 (2011)CrossRefGoogle Scholar
  6. 6.
    Zeng, X., Raghavan, J.: Role of tool-part interaction in process-induced warpage of autoclave-manufactured. Compos. Part A Appl. Sci. Manuf. 41(9), 1174–1183 (2010)CrossRefGoogle Scholar

Copyright information

© Springer International Publishing AG 2018

Authors and Affiliations

  • Fengyang Bi
    • 1
    Email author
  • Bo Yang
    • 2
  • Tianguo Jin
    • 3
  • Changxi Liu
    • 1
  • Xiaohong Wang
    • 1
  1. 1.School of Mechatronics EngineeringHeilongjiang Institute of TechnologyHarbinChina
  2. 2.State Key Laboratory of Mechanical TransmissionChongqing UniversityChongqingChina
  3. 3.School of Mechatronics EngineeringHarbin Institute of TechnologyHarbinChina

Personalised recommendations