Abstract
The current chapter applies the results of the right and skewed vortex cylinder models of rotors, respectively presented in Chaps. 17 and 21. The models are used to determine the velocity field upstream of one or several rotors, a region referred to as the induction zone for a wind turbine or a wind farm. The chapter begins with a small introduction on the topic of induction zone. The chapter briefly recalls the analytical models needed to assess the velocity field upstream of the rotor. A superposition of elementary cylindrical models is used. The superposition is described in Chap. 18 for the right cylinder and Chap. 23 for the skewed cylinder. Results are then compared to CFD actuator disk (AD) simulations in aligned and yawed conditions. Cases with and without wake rotation (swirl) are investigated for moderate and large thrust coefficients. The actuator disk simulation and vortex model results are seen to be in good agreement. The computational time required for the determination of the induction zone with the vortex model is negligible which makes the model a good candidate for the study of induction zones. The application of the model to obtain the induction zone in front of a wind farm is then presented. The effect of turbine spacing, hub-height, operating condition and wind farm layout on the wind farm induction is presented. The results show that the wind speed at 2.5D upstream of a wind farm can easily be reduced up to \(3\%\) compared to the actual free-stream. Most of the results presented in this chapter were published in the article from the author titled “Using a cylindrical vortex model to assess the induction zone in front of aligned and yawed rotors” (Branlard and Meyer Forsting, 2015, [6]). A Matlab source code to evaluate the velocity field in the entire domain induced by the main vorticity component is provided in Sects. 36.2.2 and 38.1.4 for the aligned and yawed case respectively.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Notes
- 1.
The superposition of cylindrical vortex models is presented in Chap. 18 and [3].
References
E. Branlard, M. Gaunaa, Cylindrical vortex wake model: right cylinder. Wind Energy 524(1), 1–15 (2014)
E. Branlard, M. Gaunaa, Cylindrical vortex wake model: skewed cylinder, application to yawed or tilted rotors. Wind Energy (2015)
E. Branlard, M. Gaunaa, Superposition of vortex cylinders for steady and unsteady simulation of rotors of finite tip-speed ratio. Wind Energy (2015)
E. Branlard, M. Gaunaa, Impact of a wind turbine on turbulence: un-freezing the turbulence by means of a simple vortex particle approach (2016)
E. Branlard, M. Gaunaa, E. Machefaux, Investigation of a new model accounting for rotors of finite tip-speed ratio in yaw or tilt. J. Phys.: Conf. Ser. (Online) 524(1), 1–11 (2014)
E. Branlard, A. Meyer Forsting, Using a cylindrical vortex model to assess the induction zone infront of aligned and yawed rotors, in Proceedings of EWEA Offshore 2015 Conference (2015)
T. Burton, D. Sharpe, N. Jenkins, E. Bossanyi, Wind Energy Handbook, 1st edn. (Wiley, New York, 2002)
R.P. Coleman, A.M. Feingold, C.W. Stempin, Evaluation of the induced-velocity field of an idealized helicopter rotor. NACA ARR No. L5E10 (1945), pp. 1–28
International Standard IEC, IEC 61400–12 Power performance measurements of electricity producing wind turbines. International Electrotechnical Commission, Geneva (2005)
N.E. Joukowski, Vortex theory of screw propeller, I. Trudy Otdeleniya Fizicheskikh Nauk Obshchestva Lubitelei Estestvoznaniya 16(1), 1–31 (1912) (in Russian). French translation in: Théorie tourbillonnaire de l’hélice propulsive. Gauthier-Villars: Paris 1, 1–47 (1929)
H. Madsen, R. Mikkelsen, S. Øye, C. Bak, J. Johansen, A detailed investigation of the blade element momentum (bem) model based on analytical and numerical results and proposal for modifications of the bem model. J. Phys.: Conf. Ser. 75 (2007)
H. Madsen, C. Bak, M. Døssing, R. Mikkelsen, S. Øye, Validation and modification of the blade element momentum theory based on comparisons with actuator disc simulations. Wind Energy 13, 373–389 (2010)
S. McTavish, S. Rodrigue, D. Feszty, F. Nitzsche, An investigation of in-field blockage effects in closely spaced lateral wind farm configurations. Wind Energy 18(11), 1989–2011 (2015)
A.R. Meyer, N. Troldborg, M. Gaunaa, The flow upstream of a row of aligned wind turbine rotors and its effect on power production. Wind Energy 20(1), 63–77 (2017)
J.A. Michelsen, Block Structured Multigrid Solution of 2D and 3D elliptic PDE’s. AFM 94-05 - Department of Fluid Mechanics, Technical University of Denmark (1994)
A.R. Meyer Forsting, N. Troldborg, Simulations of wind turbine induction in uniform inflow. J. Wind Energy (2017)
E. Simley, L.Y. Pao, P. Gebraad, M. Churchfield, Investigation of the impact of the upstream induction zone on lidar measurement accuracy for wind turbine control applications using large-eddy simulation. J. Phys.: Conf. Ser. 524(1), 012003 (2014)
N.N. Sørensen, General Purpose Flow Solver Applied to Flow over Hills. Ph.D thesis, Risø National Laboratory (1995)
G.A.M. van Kuik, L.E.M. Lignarolo, Potential flow solutions for energy extracting actuator disc flows. Submitted to Wind Energy (2015)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2017 Springer International Publishing AG
About this chapter
Cite this chapter
Branlard, E. (2017). Velocity Field Upstream of Aligned and Yawed Rotors: Wind Turbine and Wind Farm Induction Zone. In: Wind Turbine Aerodynamics and Vorticity-Based Methods. Research Topics in Wind Energy, vol 7. Springer, Cham. https://doi.org/10.1007/978-3-319-55164-7_24
Download citation
DOI: https://doi.org/10.1007/978-3-319-55164-7_24
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-55163-0
Online ISBN: 978-3-319-55164-7
eBook Packages: EnergyEnergy (R0)