Abstract
The issue of capillary active calcium silicate insulation used in the systems of energy redevelopment of historic buildings is a very up-to-date topic. This article describes the properties of the developed material structures built on cement composites with a defined inner surface using industrial waste materials containing aluminosilicates. The article presents the structures containing fly ashes from heating plants improving the rheological properties of the mixture and the latent hydraulic properties allowing a reduction of the necessary amount of the binding matrix, represented by cement in this case, which has a direct impact on the economy of the final material. The aim of the developed material is to extend the segment of capillary thermal insulation board materials used for the purpose of energy redevelopment of historic buildings. The article will present the parameters evaluating the capillary activity of the material, the coefficient of diffusion resistance, the thermal conductivity coefficient and the physical and mechanical properties. The acquired values are then implemented into the simulation software Delphin, taking into account the moisture transport in porous materials under non-stationary conditions. The output of the software is a simulation describing the developed material in time, after the incorporation into a moisture-defined building structure showing a disruption of the waterproofing layers of the lower structure.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Grunewald J, Ruisinger U, Häupl P (2006) The Rijksmuseum Amsterdam—hygrothermal analysis and dimensioning of thermal insulation. In: 3rd international building physics conference—research in building physics and building engineering, Canada
Ruochong Y, Jipeng Z, Zhishen W, Zhiren W, Min L, Changhai P (2011) Thermal insulation and strength of autoclaved light concrete. J Wuh Uni Tech Mater Sci Edn. doi:10.1007/s11595-011-0184-6
Ruisinger U, Grunewald J (2009) Title of preprint. http://tu-dresden.de/die_tu_dresden/fakultaeten/fakultaet_architektur/ibk/research/researchprojects/2006_Feuchteatlas/Feuchteatlas.pdf. Accessed 22 April 2009
Václavik V, Dvorský T, Dirner V, Daxner J, Šťastný M (2012) Polyurethane foam as aggregate for thermal insulating mortars and lightweight concrete. Tehnicki Vjesnik 19(3):665–672
Václavik V, Valíček J, Dvorský T, Hryniewicz T, Rokosz K, Harničárová M, Kušnerová M, Daxner J (2012) A method of utilization of polyurethane after the end of its life cycle. Rocz Ochrona Srodowiska 14:96–106
Scheffler G, Grunewald J (2003) Material development and optimisation supported by numerical simulation for a capillary-active inside insulation materiál. In: 2nd international conference on building physics, Antwerp
Stevulova N, Kidalova L, Cigasova J, Junak J, Sicakova A, Terpakova E (2013) Lightweight composites containing hemp hurds. In: 6th international conference on concrete and concrete structures 2013, Zilina
Cigasova J, Stevuvola N, Sicakova A, Junak J (2013) Some aspects of lightweight composites durability. Chem Eng Trans 32:1615–1620. doi:10.3303/CET1332270
Junak J, Stevulova N (2011) Potential of selected industrial wastes in civil engineering applications. In: 1st international multidisciplinary scientific geoconference and EXPO, Varna, 20–25 June 2011
CSN EN ISO 13788 (2013) Hygrothermal performance of building components and building elements—internal surface temperature to avoid critical surface humidity and interstitial condensation—calculation methods, (Czech normalization institute, Prague, 2013)
CSN EN 12831 (2005) Heating systems in buildings—method for calculation of the design heat load, (Czech normalization institute, Prague, 2005)
CSN EN 1015-10 (2000) Methods of test for mortar for masonry—part 10: determination of dry bulk density of hardened mortar, (Czech normalization institute, Prague, 2000)
CSN EN 12390-3 (2009) Testing hardened concrete—part 3: compressive strength of test specimens, (Czech normalization institute, Prague, 2009)
CSN EN 1015-18 (2003) Methods of test for mortar for masonry—part 18: determination of water absorption coefficient due to capillarity action of hardened mortar, (Czech normalization institute, Prague, 2003)
CSN P 73 0610 (2000) Waterproofing of buildings—the rehabilitation of damp masonry and additional protection of buildings against ground moisture and against atmospheric water—basic provision, (Czech normalization institute, Prague, 2000)
Acknowledgments
Article has been done in connection with projects:
SGS reg. no. SP2014/9 Utilization of industrial waste containing aluminosilicate for material structures with defined surface.
Institute of clean technologies for mining and utilization of raw materials for energy use—Sustainability program, reg. no. LO1406 supported by Research and Development for Innovations Operational Programme financed by Structural Founds of Europe Union and from the means of state budget of the Czech Republic.
IT4Innovations Centre of Excellence project, reg. no. CZ.1.05/1.1.00/02.0070 supported by Operational Programme Research and Development for Innovations funded by Structural Funds of the European Union and state budget of the Czech Republic.
RMTVC No. LO1203.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2015 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Břenek, A. et al. (2015). Capillary Active Insulations Based on Waste Calcium Silicates. In: Öchsner, A., Altenbach, H. (eds) Mechanical and Materials Engineering of Modern Structure and Component Design. Advanced Structured Materials, vol 70. Springer, Cham. https://doi.org/10.1007/978-3-319-19443-1_14
Download citation
DOI: https://doi.org/10.1007/978-3-319-19443-1_14
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-19442-4
Online ISBN: 978-3-319-19443-1
eBook Packages: EngineeringEngineering (R0)