Abstract
Latent heat thermal energy storages (LHTES) are particularly attractive methods owing to these factors: meet the time shift between energy supply and demand; provide a high energy storage capacity; store and release heat at a relatively constant temperature; provide constant comfort thermal environment without temperature swings when it is applied for space heating or cooling. Nevertheless, the efficiency of using the LHTES techniques is heavily affected by the low thermal conductivities of phase change materials (PCMs). This characteristic of PCMs prolongs the charging and discharging cycle and barriers the widely practical application of LHTES. Hence, researchers generated a lot of related technologies, such as metal fines, carbon fibres, metal honeycomb structure, etc, to overcome this issue and aimed to achieve reasonable thermal conductivities.
The objective of this paper is to study the heat performance of two kinds of PCMs within three different types of metal finned structures (straight fins, honeycomb and square finned structure) at the volume ratios of 1.8, 2.7, and 3.6 %, respectively. Two organic PCMs, paraffin wax RT 25 (phase transform at 25 °C) and RT 42 (phase transform at 42 °C) are employed as the heat storage media. The characteristics of them with the thermal conductivity enhancers (TCEs) during the melting and solidification process were investigated experimentally. The results indicate that the heat transfer improvements during the melting process are more efficiency than the solidification process for all of the three structures and both PCMs. To be specific, for paraffin RT 25, the heat transfer efficiencies were increased by 25, 33, and 37 %, in the finned, honeycomb and square cell structured container during the melting process, and increased by 8, 12, and 17.1 %, respectively for the solidification processes. The similar effect happened for paraffin RT 42, the heat transfer efficiencies were increased by 28, 33, and 40 % during melting process, and increased by 17, 28, and 35 %, respectively during freezing process. The performance of the TCEs on the RT 42 is slightly better than that of RT 25, especially during the solidification process due to its higher heat transfer rate between the PCM and TECs induced by a relative higher melting temperature. Meanwhile, the efficiencies of the volume ratios of the TECs were examined. The results show that straight fins have the best efficiency compared to others.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Sari A (2003) Thermal characteristics of a eutectic mixture of myristic and palmitic acids as phase change material for heating applications. Appl Therm Eng 23:1005–1017
Abhat A (1983) Low temperature latent heat thermal energy storage: heat storage materials. Sol Energ 30:313–332
Bugaje IM (1997) Enhancing the thermal response of latent heat storage systems. Int J Energ Res 21:759–766
Jegadheeswaran S, Pohekar SD (2010) Energy and exergy analysis of particle dispersed latent heat storage system. Int J Energ Environ 1(3):445–458
Sari A, Karaipekli A (2007) Thermal conductivity and latent heat thermal energy storage characteristics of paraffin/expanded graphite composite as phase change material. Appl Therm Eng 27:1271–1277
Akhilesh R, Narasimhan A, Balaji C (2005) Method to improve geometry for heat transfer enhancement in PCM composite heat sinks. Int J Heat Mass Tran 48(13):2759–2770
Huang MJ, Eames PC, Norton B (2005) Thermal regulation of building-integrated photovoltaics using phase change materials. Int J Heat Mass Tran 47(12–13):2715–2733
Robak CW, Bergman TL, Faghri A (2011) Enhancement of latent heat energy storage using embedded heat pipes. Int J Heat Mass Tran 54(15–16):3476–3484
Shabgard H, Bergman TL, Sharifi N, Faghri A (2010) High temperature latent heat thermal energy storage using heat pipes. Int J Heat Mass Tran 53(15–16):2979–2988
Lacroix M, Benmadda M (1997) Numerical simulation of natural convection dominated melting and solidification from a finned vertical wall. Numer Heat Trans Part A Appl 31(1):71–86
Lacroix M, Benmadda M (1998) Analysis of natural convection melting from a heated wall with vertically oriented fins. Int J Numer Methods Heat Fluid Flow 8(4):465–478
Eftekhar J, Sheikh AH, Lou DYS (1984) Heat transfer enhancement in a paraffin wax thermal storage system. J Sol Energ Eng 106:299–306
Abhat A (1976) Experimental investigation and analysis of a honeycomb-packed phase change material device. In: AIAA 11th thermo-physics conference, p 9 (Paper AIAA-76-437)
De Jong AG, Hoogendoorn CJ (1981) Improvement of heat transport in paraffins for latent heat storage systems, in thermal storage of solar energy. In: Proceedings of an international TNO—symposium, Martinus Nijhoff Publishers, Amsterdam, The Netherlands, pp 123–33
Website: http://www.rubitherm.de/ . Accessed June 2010, Rubitherm GmbH
Zhao CY, Lu W, Tian Y (2010) Heat transfer enhancement for thermal energy storage using metal foams embedded within phase change materials (PCMs). Sol Energ 84:1402–1412
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Nomenclature
Nomenclature
- t:
-
Time (s)
- η:
-
Efficiency
- λ :
-
Efficiency-volume ratio
- ζ :
-
Volume fraction of the heat transfer enhancer
- pure:
-
PCM without TCEs
- TCE:
-
PCM with TCEs
- LHTES:
-
Latent heat thermal energy storages
- PCM:
-
Phase change materials
- TCEs:
-
Thermal conductivity enhancers
Rights and permissions
Copyright information
© 2014 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Li, Y., Liu, S., Zhang, Y. (2014). Experimental Study of the Heat Transfer Performance of PCMs Within Metal Finned Containers. In: Dincer, I., Midilli, A., Kucuk, H. (eds) Progress in Sustainable Energy Technologies Vol II. Springer, Cham. https://doi.org/10.1007/978-3-319-07977-6_44
Download citation
DOI: https://doi.org/10.1007/978-3-319-07977-6_44
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-07976-9
Online ISBN: 978-3-319-07977-6
eBook Packages: EnergyEnergy (R0)