Abstract
The effects of the thermal post-treatments on the mechanical properties of SLMed 17-4PH stainless steel are studied. Three thermal post-treatments are carried out: (E0) as received state, (E1 and E2) solution annealing treatment and (E3) aging treatment. Microhardness, impact-strength, and wear tests are carried out to determine the effect of treatment on the mechanical properties of SLMed 17-4PH. The results showed that the hardness of 17-4PH at the E0 state is a greater than the hardness of the powder. This hardness decreases slightly from 418 HV to 384 HV after the solution annealing treatment E2 and increase again after E3 ageing treatment to around 447HV. A hardness difference between the two manufacturing directions was also observed. This difference almost disappears after the E3 ageing treatment. The impact strength results show a huge drop in impact strength for 17-4PH obtained by SLM. An improvement in wear behaviour following heat treatment, especially in the case of ageing.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
AlMangour, B., Yang, J.-M.: Improving the surface quality and mechanical properties by shot-peening of 17–4 stainless steel fabricated by additive manufacturing. Mater. Des. 110, 914–924 (2016). https://doi.org/10.1016/j.matdes.2016.08.037
Auguste, P., Mauduit, A., Fouquet, L., Pillot, S.: Study on 17–4 PH stainless steel produced by selective laser melting (2018)
Chang, C., et al.: Influence of post-heat treatments on the mechanical properties of CX stainless steel fabricated by selective laser melting. J. Mater. Sci. 55(19), 8303–8316 (2020). https://doi.org/10.1007/s10853-020-04566-x
Jessy Michla, J.R., Ravikumar, B., Ram Prabhu, T., Siengchin, S., Arul Kumar, M., Rajini, N.: Effect of nitriding on mechanical and microstructural properties of direct metal laser sintered 17–4PH stainless steel. J. Market. Res. 19, 2810–2821 (2022). https://doi.org/10.1016/j.jmrt.2022.05.198
Lashgari, H.R., Adabifiroozjaei, E., Kong, C., Molina-Luna, L., Li, S.: Heat treatment response of additively manufactured 17–4PH stainless steel. Mater Charact 197, 112661 (2023). https://doi.org/10.1016/j.matchar.2023.112661
Lashgari, H.R., Adabifiroozjaei, E., Kong, C., Molina-Luna, L., Li, S.: Heat treatment response of additively manufactured 17–4PH stainless steel. Mater Charact 197, 112661 (2023). https://doi.org/10.1016/j.matchar.2023.112661
Lashgari, H.R., Xue, Y., Onggowarsito, C., Kong, C., Li, S.: Microstructure, tribological properties and corrosion behaviour of additively manufactured 17–4PH stainless steel: effects of scanning pattern, build orientation, and single vs double scan. Mater. Today Commun. 25, 101535 (2020). https://doi.org/10.1016/j.mtcomm.2020.101535
Sghaier, T.A.M., Sahlaoui, H., Mabrouki, T., et al.: Selective laser melting of stainless-steel: a review of process, microstructure, mechanical properties and post-processing treatments. Int. J. Mater. Form. 16, 41 (2023). https://doi.org/10.1007/s12289-023-01769-w
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Sghaier, T.A.M., Sahlaoui, H., Mabrouki, T., Sallem, H., Rech, J. (2024). Mechanical Properties of Additively Manufactured 17-4PH SS: Heat Treatment. In: Mabrouki, T., Sahlaoui, H., Sallem, H., Ghanem, F., Benyahya, N. (eds) Advances in Additive Manufacturing: Materials, Processes and Applications. AIAM 2023. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-031-47784-3_4
Download citation
DOI: https://doi.org/10.1007/978-3-031-47784-3_4
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-031-47783-6
Online ISBN: 978-3-031-47784-3
eBook Packages: EngineeringEngineering (R0)