Abstract
As shown in Fig. 5.1, the conventional fretting fatigue phenomenon is recognized as follows: “When another member is in contact with the main member via surface pressure and cyclic loads are applied to the main member, microslip occurs repeatedly at the contact edge, reddish oxide abrasion powder (cocoa) is discharged, and the fatigue strength decreases.”
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Koibuchi K, Kokubo K, Hatsuda T, Hattori T (2009) Introduction to material mechanics and fatigue design for product development. Nikkan Kogyo Shimbun (in Japanese)
Shiotani Y, Matsuo Y, Hattori T, Kawada H (2010) Latest fractography—fracture surface analysis of various materials and its examples. Techno Syst (in Japanese)
Nishioka K, Hirakawa K (1970) Trends in recent research on fretting fatigue. J Jpn Soc Strength Mater 5(1):1–9 (in Japanese)
Hattori T (1994) Fretting fatigue problems in structural design. In: Waterhouse RB, Lindley TC (eds) Fretting fatigue. Mechanical Engineering Publications, pp 437–451
Okamoto N, Nakazawa M (1979) Int J Num Methods Eng 14:377
Hattori T et al (1987) Fracture mechanics analysis of fretting fatigue. Trans JSME (A) 53–492:1500–1507 (in Japanese)
Hattori T, Nakamura M, Watanabe T (2000) Fretting fatigue strength improvement method by stress relief slits, 27, 28 Nov 2000, Tokyo (in Japanese)
Hattori T, Watanabe T (2002) Effect of adjacent contact edge on fretting fatigue strength. In: JSME annual conference proceedings, vol 2, pp 483–484 (in Japanese)
Hattori T (2018) Basics of material mechanics and strength design learned from accident cases. Nikkan Kogyo Shimbun, p 187 (in Japanese)
Hattori T, Nakamura M, Ishizuka T (1992) Fretting fatigue analysis of strength improvement models with grooving or knurling on a contact surface. ASTM STP 1159: 101–114
Sakata H et al (1987) Role of fracture mechanics in modern Techniques, 303
Ezawa Y et al (1985) Boundary elements VII. In: Proceeding of the 7th international conference, Como, Italy, Springer-Verlag
Hattori T et al (1981) Trans JSME 39–326:264
Sonobe et al (1980) Hitachi Rev 62–10:57 (in Japanese)
Hattori T et al (1984) Proceedings of 1983 Tokyo international gas turbine congress, 945
Hattori T (1994) Fretting fatigue problems in structural design, vol 18. ESIS Publication, pp 437–460
National Transportation Safety Board (NTSB) (2018) Materials laboratory factual report No. 17–043, 14 June 2018
Bignonnet A (1994) Some observations of the effect of shot peening on fretting fatigue. Fretting Fatigue ESIS 18:475–482
Makino T, Sakai H (2013) Fatigue characteristics of Shinkansen axle. Nippon Steel & Sumikin Technical Report, No. 395, 56–63 (in Japanese)
Hirakawa K, Toyama K (1994) Fretting Fatigue ESIS 18:461
Japanese Industrial Standards JIS E 4502-1-2001 railway vehicle axles—quality requirements (in Japanese)
Japanese Industrial Standards JIS E 4502-1-2001 axle for railway vehicles—dimensional requirements (in Japanese)
Japan Railway Vehicle Manufacturers Association Standard JRIS J 0401-2007 railway vehicles—induction hardened axles for high-speed vehicles (in Japanese)
Makino T, Kato T, Hirakawa K (2011) Eng Fract Mech 78(5):810
Wheelset Research Committee for high-speed vehicles, railway axle, 1st edn. Maruzen Planet, Tokyo, 2010, p 110 (in Japanese)
Japanese Industrial Standards JIS E 4504-1-2000 axle for railway vehicles—quality requirements (in Japanese)
Kawamoto M, Nishioka K (1952) Study on improvement of fatigue limit by surface rolling (1st report). Trans Jpn Soc Mech Eng 18–68:104–107 (in Japanese)
Filimonov GN (1994) Improving the fretting fatigue resistance of large shafts with the use of surface cold working. Fretting Fatigue ESIS 18:483–495
Shkolnik LM, Shakhov VI (1964) Surface rolling technology and rigs for strengthening and finishing of components. Mashinostrojenije, Moscow
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this chapter
Cite this chapter
Hattori, T. (2024). Prevention Technology for Fretting Damage. In: Fretting Wear, Fretting Fatigue and Damping of Structures. Solid Mechanics and Its Applications, vol 276. Springer, Cham. https://doi.org/10.1007/978-3-031-46498-0_5
Download citation
DOI: https://doi.org/10.1007/978-3-031-46498-0_5
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-031-46497-3
Online ISBN: 978-3-031-46498-0
eBook Packages: EngineeringEngineering (R0)