Abstract
Steel for transport and handling equipment should provide the required reliability at a lower level of costs in manufacturing and operation. To determine the relationship between mechanical, structural, and magnetic parameters, the change in the stray magnetic field under the application of external loads was measured, and then the magnetic field diagram was superimposed on the tension diagram. The passive fluxgate method was used to measure the stray magnetic field; steels 08ps and 09G2S were used as the object of study. In the course of the study, measurements of the magnetic stray field were carried out under stepped loading of metal structures. As a result, the dependence of the stray magnetic field on the magnitude of the metal structure stretching was established. Thermal hardening of these steels gives an increase in the yield strength by 25…30% and tensile strength by 15…20%, as well as a shift in the cold brittleness threshold by 15…20 °C towards negative temperatures.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Bajaj P, Hariharan A et al (2020) Steels in additive manufacturing: a review of their microstructure and properties. Mater Sci Eng A 772:138633. https://doi.org/10.1016/j.msea.2019.138633
Brika SE, Letenneur M, Dion CA, Brailovski V (2020) Influence of particle morphology and size distribution on the powder flowability and laser powder bed fusion manufacturability of Ti-6Al-4V alloy. Addit Manuf 31:100929. https://doi.org/10.1016/j.addma.2019.100929
Cui C, Uhlenwinkel V, Schulz A, Zoch HW (2020) Austenitic stainless steel powders with increased Nitrogen content for laser additive manufacturing. Metals 10:61. https://doi.org/10.3390/met10010061
Kumar SS, Marandi L, Balla VK et al (2019) Microstructure—property correlations for additively manufactured NiTi based shape memory alloys. Materialia 8:100456. https://doi.org/10.1016/j.mtla.2019.100456
Lou X, Andresen PL, Rebak RB (2018) Oxide inclusions in laser additive manufactured stainless steel and their effects on impact toughness and stress corrosion cracking behavior. J Nucl Mater 499:182–190. https://doi.org/10.1016/J.JNUCMAT.2017.11.036
Mantrala KM, Das M et al (2015) Additive manufacturing of Co-Cr-Mo alloy: influence of heat treatment on microstructure, tribological and electrochemical properties. Front Mech Eng 1:2. https://doi.org/10.3389/fmech.2015.00002
Mukherjee M (2019) Effect of build geometry and orientation on microstructure and properties of additively manufactured 316L stainless steel by laser metal deposition. Materialia 7:100359. https://doi.org/10.1016/j.mtla.2019.100359
Saeidi K, Gao X, Zhong Y, Shen ZJJ (2014) Hardened austenite steel with columnar sub-grain structure formed by laser melting. Mater Sci Eng A 625:221–229. https://doi.org/10.1016/j.msea.2014.12.018
Sames WJ et al (2016) The metallurgy and processing science of metal additive manufacturing. Int Mater Rev 61:315–360. https://doi.org/10.1080/09506608.2015.1116649
Scherbakov A, Monastyreva D, Smirnov V (2019) Passive fluxgate control of structural transformations in structural steels during thermal cycling. E3S Web Conf 135:03022. https://doi.org/10.1051/e3sconf/201913503022
Scherbakov A, Babanina A, Graboviy K (2021) Acting stresses in structural steels during elastoplastic deformation. Adv Intel Syst Comp 1259:298–311. https://doi.org/10.1007/978-3-030-57453-6_26
Scherbakov A, Babanina A, Kochetkov I, Khoroshilov P (2020) Technical condition of welded load-bearing metal structures of operated agricultural hoisting cranes. E3S Web Conf 175:11005. https://doi.org/10.1051/e3sconf/202017511005
Scherbakov A, Babanina A, Matusevich A (2021) Passive probe-coil magnetic field test of stress-strain state for welded joints. Adv Intel Syst Comp 1259:312–323. https://doi.org/10.1007/978-3-030-57453-6_27
Tan C, Zhou K et al (2017) Microstructural evolution, nanoprecipitation behavior and mechanical properties of selective laser melted high-performance grade 300 maraging steel. Mater Des 134:23–34. https://doi.org/10.1016/j.matdes.2017.08.026
Wołosz P, Baran A, Polański M (2020) The influence of laser engineered net shaping (LENS™) technological parameters on the laser deposition efficiency and properties of H13 (AISI) steel. J Alloys Compd 823:153840. https://doi.org/10.1016/j.jallcom.2020.153840
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2023 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Scherbakov, A., Aleksandrovskiy, M., Shavelkin, D., Verbova, N. (2023). Method for Obtaining Structures with a Given Degree of Dispersion in Low-Carbon and Low-Alloy Steels of Transport and Handling Equipment. In: Guda, A. (eds) Networked Control Systems for Connected and Automated Vehicles. NN 2022. Lecture Notes in Networks and Systems, vol 510. Springer, Cham. https://doi.org/10.1007/978-3-031-11051-1_127
Download citation
DOI: https://doi.org/10.1007/978-3-031-11051-1_127
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-031-11050-4
Online ISBN: 978-3-031-11051-1
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)