Abstract
An overwhelming number of defects occur for production reasons due to technology deficiencies. The thermal-impulse method allows you to flexibly automate the cleaning operations from technological contaminants in particles, burrs and quickly wearing out part of the microrelief when obtaining a close to the absolute degree of cleaning surfaces and edges the listed liquids. The technological capabilities of thermal-impulse treatment, control parameters, and factors on which the rational choice of processing modes for machine parts and mechanisms depend are considered. The factors influencing the determination of the optimal modes of cleaning the edges and surfaces of the parts and the factors allowing to form the technical characteristics of the heat source and equipment as a whole, realizing the optimal modes with self-regulation properties, have been determined and systematized. Parts were analyzed after processing by thermal impulse method and for comparison with thermochemical. Therefore, detonating gas technologies are the most attractive because of their versatility and flexibility concerning parts with complex configurations of internal and external surfaces.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
1. References
Niknam, S., Davoodi, B., Davim, J.P., Songmene, V.: Mechanical deburring and edge-finishing processes for aluminum parts—a review. Int. J. Adv. Manuf. Technol. 95(1–4), 1101–25 (2018)
ALP De San Román, Chaves-Jacob, J., Linares, J.M., Arrazola, P.J.: Analytical-method for polishing-surface prediction considering tool flexibility and grain-material interaction. J. Mater. Process. Technol., 117208 (2021)
Balázs, B.Z., Takács, M.: Experimental investigation and optimisation of the micro milling process of hardened hot-work tool steel. Int. J. Adv. Manuf. Technol. 106(11–12), 5289–5305 (2020). https://doi.org/10.1007/s00170-020-04991-x
Chen, L., Deng, D., Pi, G., Huang, X., Zhou, W.: Burr formation and surface roughness characteristics in micro-milling of microchannels. Int. J. Adv. Manuf. Technol. 111(5–6), 1277–1290 (2020). https://doi.org/10.1007/s00170-020-06170-4
Chen, W., Teng, X., Zheng, L., Xie, W., Huo, D.: Burr reduction mechanism in vibration-assisted micro milling. Manuf. Lett. 16(2018), 6–9 (2018)
Chen, Y., Wang, T., Zhang, A.G.: Research on parameter optimization of micro-milling al7075 based on edge-size-effect. Micromachines 11(2), 1–15 (2020)
Hanson, C., Hiwase, P., Chen, X., Jahan, M.P., Ma, J., Arbuckle, G.: Experimental investigation and numerical simulation of burr formation in micro-milling of polycarbonates. Procedia Manuf. 34(2019), 293–304 (2019)
Khan, K., Varghese, A., Dixit, P., Joshi, S.S.: Effect of tool path complexity on top burrs in micromilling. Procedia Manuf. 34(2019), 432–439 (2019)
Hajiahmadi, S.: Burr size investigation in micro milling of stainless steel 316L. Int. J. Lightweight Mater. Manufacture 2(4), 296–304 (2019)
Ivanov, V., Vashchenko, S., Rong, Y.: Information support of the computer-aided fixture design system. In: CEUR Workshop Proceedings, vol. 1614, pp. 73–86 (2016)
Akimov, O.V., et al.: Computer engineering and design of cast parts for internal combustion engine crankcase. J. Eng. Sci. 6(2), E24–E30 (2019). https://doi.org/10.21272/jes.2019.6(2).e4
Kiran, A.V.N.S., Ramanjaneyulu, B., Lokanath, M., Nagendra, S., Balachander, G.E.: Control of exhaust emissions using piston coating on two-stroke SI engines with gasoline blends. J. Eng. Sci. 8(1), H16–H20 (2021). https://doi.org/10.21272/jes.2021.8(1).h3
Aurich, J.C., Dornfeld, D., Arrazola, P.J., Franke, V., Leitz, L., Min, S.: Burrs-Analysis, control and removal. CIRP Ann. Manuf. Technol. 58, 519–542 (2009)
Rui, Z., Zi, Z., Minghui, H.: The art of laser ablation in aeroengine: the crown jewel of modern industry. J. Appl. Phys. 127, 080902 (2020). https://doi.org/10.1063/1.5134813
Kumar, M., Bajpai, V.: Experimental investigation of top burr formation in high-speed micro-milling of Ti6Al4V alloy. Proc. Inst. Mech. Eng. Part B: J. Eng. Manuf. 234(4), 730–738 (2019)
Loseva, O., Losev, A., Majorova, E.: Development of physical and mathematical models of impulse-periodic processes of heating the elements of the part. In: Proceedings International Scientific and Practical Conference Public communication in science: philosophical, cultural, political, economic and IT context. Collection of scientific papers «ΛΌГOΣ», vol. 2, pp. 97–104. European Scientific Platform, Houston, USA (2020)
Jin, S.Y., Pramanik, A., Basak, A.K., Prakash, C., Shankar, S., Debnath, S.: Burr formation and its treatments—a review. Int. J. Adv. Manuf. Technol. 107(5–6), 2189–2210 (2020). https://doi.org/10.1007/s00170-020-05203-2
Ivanov, V., Pavlenko, I., Liaposhchenko, O., Gusak, O., Pavlenko, V.: Determination of contact points between workpiece and fixture elements as a tool for augmented reality in fixture design. Wireless Netw. 27(3), 1657–1664 (2019). https://doi.org/10.1007/s11276-019-02026-2
Pavlenko, I., et al.: Parameter identification of cutting forces in crankshaft grinding using artificial neural networks. Materials 13(23), 5357 (2020). https://doi.org/10.3390/ma13235357
Abele, E., Schützer, K., Güth, S., Meinhard, A.: Deburring of cross-drilled holes with ball-end cutters—modeling the tool path. Prod. Eng. Res. Devel. 12(1), 25–33 (2017). https://doi.org/10.1007/s11740-017-0781-0
Acknowledgment
This research was partially supported by International Association for Technological Development and Innovations.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2022 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Losev, A., Bychkov, I., Selezneva, A., Shendryk, V., Shendryk, S. (2022). Cleaning of Parts with Detonating Gas Mixtures. In: Tonkonogyi, V., Ivanov, V., Trojanowska, J., Oborskyi, G., Pavlenko, I. (eds) Advanced Manufacturing Processes III. InterPartner 2021. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-91327-4_58
Download citation
DOI: https://doi.org/10.1007/978-3-030-91327-4_58
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-91326-7
Online ISBN: 978-3-030-91327-4
eBook Packages: EngineeringEngineering (R0)