Abstract
A number of finite element (FE) models with Lagrangian formulation have been developed to simulate the high-speed particle impact. Although the Lagrangian formation-based FE models developed so far contributed significantly to unveiling the important questions on the mechanics of particle impact, they have a critical weakness. The Lagrangian models often diverge under large deformation due to mesh distortion. Recently, FE models based on Eulerian formation have been developed. This research describes a part of such efforts. A thin three-dimensional finite element model of high-speed impact of a micron-sized metallic particle was developed using Eulerian formulation. The meshes of a finite element model based on Eulerian formulation do not deform and therefore allow for dealing with a case with extreme plastic deformation. The two cases from the literature were reproduced to evaluate the validity of the developed model. After comparison, the model was used to simulate the impact of a stainless steel particle on a stainless steel substrate at an impact speed of 1000 m/s, which could not be readily simulated using the Lagrangian model.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Alkhimov AP, Papyrin AN, Kosarev VF, Nesterovich NI, Shuschpanov MM (1994) Gas dynamic spraying method for applying a coating, The United States
Champagne VK, Helfritch D (2014) Critical assessment 11: structural repairs by cold spray. Mater Sci Technol 31:627–634
Assadi H, Gaetner F, Stolenhoff T, Kreye H (2003) Bonding mechanism in cold gas spraying. Acta Mater 51:4379–4394
Wang X, Shi J (2013) Validation of Johnson-Cook plasticity and damage model using impact experiment. Int J Impact Eng 60:67–75
Yildrim B, Muftu S, Gouldstone A (2011) Modeling of high velocity impact of spherical particles. Wear 207:703–713
Schmidt T, Gartner H, Assadi H, Kreye H (2006) Development of a Generalized Parameter Window for Cold Spray Deposition. Acta Mater 54:729–742
Wang FF, Li W-Y, Yu M, Liao H (2014) Prediction of critical velocity during cold spraying based on a coupled thermomechanical Eulerian model. J Therm Spray Technol 23:60–67
Li W-Y, Gao W (2009) Some aspects on 3D numerical modeling of high velocity impact of particles in cold spraying by explicit finite element analysis. Appl Surf Sci 255:7878–7892
Li W-Y, Liao H, Li C-J, Bang HS, Coddet C (2007) Numerical simulation of deformation behavior of Al particles impacting on Al substrate and effect of surface oxide films on interfacial bonding in cold spraying. Appl Surf Sci 253:5084–5509
Shah S, Lee J, Rothstein JP (2017) Numerical Simulations of the High-Velocity Impact of a Single Polymer Particle During Cold-Spray Deposition. J Therm Spray Technol 26:970–984
Abaqus Analysis User’s Manual. Dassualt Systemes, 2007
Yin S, Wang XF, Xu BP, Li W-Y (2010) Examination on the Calculation Method for Modeling the Multi-Particle Impact Process in Cold Spraying. J Therm Spray Technol 19:1032–1041
Krasauskas P, Kilikevicius S, Cesnavicius R, Pacenga D (2014) Experimental analysis and numerical simulation of the stainless AISI 304 steel friction drilling process. Mechanika 20:590–595
Nahshon K, Pontin MG, Evans AG, Hutchinson JW, Zok FW (2007) Dynamic shear rupture of steel plates. J Mech Mater Struct 2:2049–2066
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Minerals, Metals & Materials Society
About this paper
Cite this paper
Wong, C.V., Lee, J. (2021). Numerical Simulation of Microscale Metallic Particle Impact Using Eulerian Approach. In: Lee, J., Wagstaff, S., Anderson, A., Tesfaye, F., Lambotte, G., Allanore, A. (eds) Materials Processing Fundamentals 2021. The Minerals, Metals & Materials Series. Springer, Cham. https://doi.org/10.1007/978-3-030-65253-1_22
Download citation
DOI: https://doi.org/10.1007/978-3-030-65253-1_22
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-65252-4
Online ISBN: 978-3-030-65253-1
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)