Abstract
This paper proposes a numerical method using Taylor series in representing a new series motor of a four-quadrant drive direct current chopper (FQDC) in driving mode operation for electric vehicle’s application. The representation has three main purposes which are for troubleshooting, error correction and optimization. The Taylor series will be used to imitate the real system of a FQDC, but it is running in an embedded system such as a PIC microcontroller. Through this representation system, we can do a fault diagnose, error correction and system tuning without disturbing the real system on running. Once the optimization via representation is obtained, it can be applied to the real system. The representation system using Taylor series is tested using MATLAB/Simulink. The simulation results using MATLAB/Simulink show that the Taylor series computation algorithm successfully represents the FQDC in driving mode.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Oak Ridge National Laboratory: Advanced Brush Technology for DC Motors (2009). Available: http://peemrc.ornl.gov/projects/emdc3.jpg
Arof, S., Jalil, J.A., Yaakop, N.M., Mawby, P.A., Arof, H.: Series motor four quadrants drive DC chopper part 1: overall. In: International Conference on Power Electronics. IEEE, 2015 (2014)
Arof, S., Diyanah, N.H.N., Noor, N.M., JalilP. J.A., Mawby, A., Arof. H.: A new four quadrants drive chopper for separately excited DC motor in low cost electric vehicle. Prog. Eng. 119–138 (2019). https://doi.org/10.1007/978-3-030-28505-0_10
Arof, S., Hassan, H., Rosyidi, M., Mawby, P.A., Arof, H.: Implementation of Series motor four quadrants Drive dc chopper for dc drive electric car and LRT via simulation model. J. Appl. Environ. Biol. Sci., 7(3S), 73–82 (2017)
Arof, S., Noor, N.M., Elias, F., Mawby, P.A., Arof, H.: Investigation of chopper operation of series motor four quadrants DC chopper. J. Appl. Environ. Biol. Sci., 7(3S), 49–56 (2017)
Arof, S., Jalil, J.A., Kamaruddin, N.H., Yaakop, N.M., Mawby, P.A., Arof, H.: Series motor four quadrants drive DC chopper part 2: driving and reverse with direct current control. In: International Conference on Power Electronics, pp. 775–780 (2016). 978-1-5090-2547-3/16. https://doi.org/10.1109/pecon.2016.7951663
Arof, S., Diyanah, N.H.N., Noor, N.M.N., Radzi, J.M., Jalil, A., Mawby, P.A., H. Arof, H.: Series motor four quadrants drive DC chopper: Part 4: generator mode. Prog. Eng. 155–167 (2019). https://doi.org/10.1007/978-3-030-28505-0_12
Arof, S., Diyanah, H.N., Yaakop, M., Mawby, P.A., Arof, H.: Processor in the loop for testing series motor four quadrants drive direct current chopper for series motor driven electric car: part 1: chopper operation modes testing. Adv. Eng. Process. Technol. 59–76 (2019). https://doi.org/10.1007/978-3-030-05621-6_5
Arof, S., Muhd Khairulzaman, A.K., Jalil, J.A., Arof, H., Mawby, P.A.: Self tuning fuzzy logic controlling chopper operation of four quadrants drive DC chopper for low cost electric vehicle. In: 6th International Conference on Intelligent Systems, Modeling and Simulation, IEEE computer Society, pp. 40–45 (2015)
Arof, S., Zaman, M.K., Jalil, J.A., Mawby, P.A., Arof, H.: Artificial intelligence controlling chopper operation of four quadrants drive DC chopper for low cost electric vehicle. Int. J. Simul., Syst. Sci., Technol (2015), https://doi.org/10.5013/ijssst.a.16.04.03,2015
Arof, S., Diyanah, N.H., Mawby, P.A., Arof, H.: Study on implementation of neural network controlling four quadrants direct current chopper: part 1: using single neural network controller with binary data output. Adv. Eng. Process. Technol. 37–57 (2019)
Arof, S., Diyanah, N.H.N., Noor, N.M., Rosyidi, M., Mawby, P.A., Arof, H.: Genetics algorithm for setting up look up table for parallel mode of new series motor four quadrants dc chopper. Prog. Eng. 155–167 (2019) https://doi.org/10.1007/978-3-030-28505-0_12
Arof, S., Diyanah N.H.N., Mawby, P., Arof, H., Yaakop, N.M.: Low harmonics plug-in home charging electric vehicle battery charger utilizing multi-level rectifier, zero crossing and buck chopper: part 1: general overview. Prog. Eng. Technol. 103–108 (2019). https://doi.org/10.1007/978-3-030-28505-0_9
Hassan, M., Mohd, T.A.T.: Mathematical modeling and simulation of an electric vehicle. J. Mech. Eng. Sci. (JMES) (2015)
Chau, K.T., Chan, C.C., Liu, C., Lin, F.: Fault diagnosis of power components in electric vehicles. J. Asian Electr. Veh. 11(2), (2013)
Xianjin, H., Yannan, Y., Chen, X., Jie, L., Liwei, Z.: Summarize of electric vehicle electric system fault and fault-tolerant technology. 12(2), 1094–1099 (2014)
Kunovsky, J.: Modern Taylor Series Method (2015)
Nilsson, P., Shaik, A.U.R., Gangarajaiah, R., Hertz, E.: Hardware Implementation of the Exponential Function Using Taylor Series (2014)
Weirich, M.R., Paim, G., da Costa, E.A., Bampi, S.: A Fixed-Point Natural Logarithm Approximation Hardware Design Using Taylor Series (2018)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 The Editor(s) (if applicable) and The Author(s), under exclusive license to Springer Nature Switzerland AG
About this chapter
Cite this chapter
Arof, S. et al. (2020). Discrete-Time Linear System of New Series Motor Four-Quadrant Drive Direct Current Chopper Numerically Represented by Taylor Series. In: Abu Bakar, M., Azwa Zamri, F., Öchsner, A. (eds) Progress in Engineering Technology II. Advanced Structured Materials, vol 131. Springer, Cham. https://doi.org/10.1007/978-3-030-46036-5_10
Download citation
DOI: https://doi.org/10.1007/978-3-030-46036-5_10
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-46035-8
Online ISBN: 978-3-030-46036-5
eBook Packages: EngineeringEngineering (R0)