Abstract
Additive manufacturing (AM), also known as 3D-printing, is already well established for its use in rapid prototyping. Increasingly, however, AM technology is being used for end use manufacturing. The ability to create multi-material and blended material components in a single process allows for unique properties and complex structures that are difficult or impossible to produce using traditional manufacturing techniques. In order to properly utilize these materials, it is necessary to quantify and understand the mechanical properties. In this study, a Stratasys PolyJet (J750) material jetting printer was used to fabricate transparent laminates with blends of a rigid, transparent polymer (VeroClear) and a rubber-like polymer (Agilus30). The rate of deformation as well as the thickness and numbers of layers in the material influence the material’s strength and stiffness, with failure largely occurring at interfaces between the two materials. The experimental setup and results are discussed.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Das, S.C., Ranganathan, R.: Effect of build orientation on the strength and cost of PolyJet 3D printed parts. Rapid Prototyp. J. 24, 832–839 (2018)
Vu, I., Bass, L., Meisel, N., Orler, B., Williams, C.B., Dillard, D.A., Characterization of Multi-Material Interfaces in PolyJet Additive Manufacturing. Solid Freeform Fabrication Symposium. 959–982 (2015)
Dizon, J.R., Espera, A.H., Chen, Q., Advincula, R.C.: Mechanical characterization of 3D-printed polymers. Addit. Manuf. 20, 44–67 (2018)
Vu, I.Q., Bass, L.B., Williams, C.B., Dillard, D.A.: Characterizing the effect of print orientation on interface integrity of multi-material jetting additive manufacturing. Addit. Manuf. 22, 447–461 (2018)
Gay, P., Blanco, D., Pelayo, F., Noriega, A., Fernandez, P.: Analysis of factors influencing the mechanical properties of flat PolyJet manufactured parts. Procedia Eng. 132, 70–77 (2015)
Tsouknidas, A., Pantazopoulos, M., Katsoulis, I., Fasnakis, D., Maropouls, S., Michailidis, N.: Impact absorption capacity of 3D-printed components fabricated by fused deposition modeling. Mater. Des. 102, 41–44 (2016)
Chen, W., Lu, F., Zhou, B.: A quartz-crystal-embedded split Hopkinson pressure bar for soft materials. Exp. Mech. 40(1), 1–6 (2000)
Chen, W., Song, B.: Split Hopkinson (Kolsky) Bar Design, Testing, and Applications. Springer, Berlin (2011)
Acknowledgements
The research reported in this document was performed in connection with contract/instrument W911QX-16-D-0014 with the U.S. Army Research Laboratory. The views and conclusions contained in this document are those of SURVICE Engineering and the U.S. Army Research Laboratory. Citation of manufacturer’s or trade names does not constitute an official endorsement or approval of the use thereof. The U.S. Government is authorized to reproduce and distribute reprints for Government purposes notwithstanding any copyright notation hereon.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Society for Experimental Mechanics, Inc.
About this paper
Cite this paper
Harr, M., Moy, P., Yu, J. (2020). Mechanical Properties of Transparent Laminates Fabricated Using Multi-Material Photopolymer Jetting. In: Lamberson, L. (eds) Dynamic Behavior of Materials, Volume 1. Conference Proceedings of the Society for Experimental Mechanics Series. Springer, Cham. https://doi.org/10.1007/978-3-030-30021-0_8
Download citation
DOI: https://doi.org/10.1007/978-3-030-30021-0_8
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-30020-3
Online ISBN: 978-3-030-30021-0
eBook Packages: EngineeringEngineering (R0)