Abstract
The surface roughness is a decisive criterion for the quality of the machined surface. Many researchers are interested to study the effects of the machining parameters on the surface quality as: the cutting conditions, the machining strategies, the tool geometries and the machining errors. All these studies are developed for the stationary feed rate and neglected the cinematic effects caused by machine deceleration and acceleration when the tool trajectories change a direction. The objective of this research was to investigate the effect of the velocity changes on the surface roughness. A set of machining tests in high-speed end-milling of the 42CrMo4 material by a ball nose end-mill is made. For the same cutting conditions, the roughness is measured on three zones respectively the acceleration, the stationary and the deceleration zone. It was seen that the cinematic change causes a poor surface roughness.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Mersni W, boujelbene M, ben Salem S, Alghamdi A-S (2018) Optimization of the surface roughness in ball end milling of titanium alloy Ti–6Al–4 V using the Taguchi method. Proc Manuf 20: 271–276
Bouzid W, Zghal A, Sai L (2004) Taguchi method for design optimization of milled surface roughness. Mater Technol 19–3:159–162
Sekulic Pejic M, Brezocnik V, Gostimirović M, Hadzistevic M (2018) Prediction of surface roughness in the ball-end milling process using response surface methodology, genetic algorithms, and grey wolf optimizer algorithms. Adv Prod Eng Manag 13–1:18–30
Wojciechowski S, Twardowski P, Chwalczuk T (2013) Surface roughness of hardened steel after ball end milling with various surface inclinations. Arch Mech Technol Autom 33–1:55–64
Hossain MSJ, Nafis A (2012) Surface roughness prediction modeling for AISI 4340 after ball end mill operation using artificial intelligence. I J Sci Eng Res 3–5:1–10
Dikshit MK, Puri AB, Maity A (2016) Optimization of surface roughness in ball-end milling using teaching-learning-based optimization and response surface methodology. J Eng Manuf 1–12
Jatti VS, Sekhar R, Patil RK (2013) Study of ball nose end milling of LM6 Al Alloy: surface roughness optimization using genetic algorithm. I J Eng Tech 5–3:2859–2865
Kurt M, Hartomacýoðlu S, Mutlu B, Köklü U (2012) Minimization of the surface roughness and form error on the milling of free-form surfaces using a grey relational analysis. Mater Technol 46–3:205–213
Quintana G, Ciurana J, Ribatallada J (2010) Surface roughness generation and material removal rate in ball end milling operations. Mater Manuf Process 25–6:386–398
Vishal KM, Pankaj K, Baljeet S (2014) A review of optimization of surface roughness of Inconel 718 in end milling using Taguchi method. J Eng Res Appl 4–12:103–109
Chuan S, Peiqing Y (2011) The look-ahead function-based interpolation algorithm for continuous micro-line trajectories. I J Adv Manuf Technol 54:649–668
Acknowledgements
The work is carried out thanks to the support and funding allocated to the Unit of Mechanical and Materials Production Engineering (UGPM2/UR17ES43) by the Tunisian Ministry of Higher Education and Scientific Research.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this paper
Cite this paper
Lotfi, S., Rami, B., Maher, B., Gilles, D., Wassila, B. (2020). The Effect of High-Speed Milling on Surface Roughness of 42CrMo4 Hardened Steel Using a Ball Nose End-Mill Cutter. In: Aifaoui, N., et al. Design and Modeling of Mechanical Systems - IV. CMSM 2019. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-27146-6_40
Download citation
DOI: https://doi.org/10.1007/978-3-030-27146-6_40
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-27145-9
Online ISBN: 978-3-030-27146-6
eBook Packages: EngineeringEngineering (R0)