Abstract
Restoration of worn turbine rotor journal without removing it from a power unit is carried out with location on cylindrical plain bearing bottom half. Thus, the workpiece is located on the machinable surface. Such location causes difficulties in the required cylindrical accuracy guaranteeing. Our earlier studies were based on the assumption that the worn rotor journal is dominantly a cylindrical surface and has a multi-lobed directional line in its radial cross section. This assumption makes it possible to determine rational parameters of the technological operation, including the variation of tool radial feed. The purpose of the present research is to study the influence of parameters, which characterize the entire surface of a worn rotor journal under the assumption that the surface does not belong to the class of cylindrical surfaces. It is proposed to describe the surface by classifying its inaccuracy into three main types of profile errors: radial, axial, and screw. Each of these error types is described by Fourier trigonometric series. The paper presents preliminary modeling of such complex surface machining with its location on a semi-cylinder and the identification of the relation of surface dominant harmonics and of tool radial feed variation on the machining accuracy. It has been determined that the highest accuracy is obtained using the coefficient of circular frequency in feed variation equal to (or exceeding by 3 or 4) the similar coefficient of the dominant harmonic of the transverse workpiece profile.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Mobile Lathe Information Sheet (2008) Alstom, France, Saint-Ouen, 3 p
Bloch HP, Geitner FK (2005) Machinery component maintenance and repair: practical machinery management for process plants. Elsevier Inc., USA, 630 p
Orbital Tool Technologies (2012) Shaft and journal repair, USA, 2 p
Portable machine tools (2011) Solutions for all in situ site machining applications, Acteon, Derby, UK, 13 p
Molochek V (1968) Remont parovyh turbin (Steam turbine repair). Energy, Moscow, 376 p
Brian RW (2009) Principles of modern grinding technology. William Andrew, USA, 416 p
Kang K (2003) Modelling of the centerless infeed (plunge) grinding process. KSME Int J. 17(7):1026–1035
Wu Y, Kondo T, Kato M (2005) A new centerless grinding technique using a surface grinder. J Mater Process Technol 162–163:709–717
Xu W, Wu Y, Sato T, Lin W (2010) Effects of process parameters on workpiece roundness in tangential-feed centerless grinding using a surface grinder. J Mater Process Technol 210:759–766
Xu W, Wu Y (2011) A new in-feed centerless grinding technique using a surface grinder. J Mater Process Technol 211:141–149
Xu W, Wu Y (2011) A new through-feed centerless grinding technique using a surface grinder. J Mater Process Technol 211:1599–1605
Xu W, Wu Y (2012) Simulation investigation of through-feed centerless grinding process performed on a surface grinder. J Mater Process Technol 212:927–935
Shchurova AV (2016) Modeling of the turbine rotor journal restoration on horizontal balancing machines. Procedia Eng 150:854–859
Shchurova AV (2017) Modeling the turbine rotor journal restoration located on cylindrical surface of the supporting bearer. Procedia Eng 206:1142–1147
Shchurova AV (2017) Izmenenie polozheniya osi vala pri ego shlifovanii s bazirovaniem v polucilindricheskoj opore (Axis relocation of a grinded shaft that is located on hemi-cylindrical bearing seat). Bull Tula State Univ Ser Tech Sci 8(1):338–344
Franceschini F, Galetto M, Maisano D, Mastrogiacomo L (2016) Combining multiple large volume metrology systems: competitive versus cooperative data fusion. Precis Eng 43:514–524
Besic I, Gestel VN, Kruth J-P, Bleys P, Hodolic J (2011) Accuracy improvement of laser line scanning for feature measurements on CMM. Opt Lasers Eng 49(11):1274–1280
Moroni G, Syam WP, Petro S (2014) Performance improvement for optimization of the non-linear geometric fitting problem in manufacturing metrology. Meas Sci Technol 25:1–15
Du Z, Wu Z, Yang J (2016) Error ellipsoid analysis for the diameter measurement of cylindroid components using a laser radar measurement system. Meas Sci Technol 27(12):1–13
Shchurova AV (2018) Effect of the tool-operating mode on circularity deviation in multi-lobed turbine rotor journal restoration with location on a bearing bottom half. Lecture Notes in Mechanical Engineering, in press
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this paper
Cite this paper
Shchurova, A.V. (2020). 3D Modeling of Turbine Rotor Journal Machining with Location on a Bearing Bottom Half. In: Radionov, A., Kravchenko, O., Guzeev, V., Rozhdestvenskiy, Y. (eds) Proceedings of the 5th International Conference on Industrial Engineering (ICIE 2019). ICIE 2019. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-22063-1_21
Download citation
DOI: https://doi.org/10.1007/978-3-030-22063-1_21
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-22062-4
Online ISBN: 978-3-030-22063-1
eBook Packages: EngineeringEngineering (R0)