Advertisement

Effect of Applied Stress during Irradiation at 5 K on the Shear / Compression Strength of Bonded Specimens

  • D. Evans
  • R. P. Reed
Part of the Advances in Cryogenic Engineering book series (ACRE, volume 44)

Abstract

Insulation and bonding materials which are used to construct superconducting magnets for use in fusion reactors, such as ITER, will be subjected to an applied mechanical stress and also to intense neutron irradiation. There is little design information available on the effects of ionising radiation on materials when they are subjected to low temperatures and to an applied stress. The work reported was undertaken to assess the effects of a stress applied to the specimen during irradiation at 5 K. Specimens of commercially pure titanium were prepared and bonded in a geometry which would induce combined shear and compression stresses when the samples were mechanically loaded. A number of specimens were bonded using S2 glass fabric pre-impregnated with an epoxide resin and others were prepared using dry glass fabric followed by vacuum impregnation with an epoxide resin. Test specimens based on both types of resin were reactor irradiated at 4 K, with and without an applied stress of 30 MPa. A series of specimens, were cooled to 5 K and retained as non-irradiated controls.

Keywords

Glass Fabric International Thermonuclear Experimental Reactor Vacuum Impregnation Epoxide Resin Unstressed Control 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    N.J. Simon. “A Review of Irradiation Effects On Organic Matrix Insulation”. U.S. Dept of Commerce, National Institute of Standards and Technology, NISTIR 3999. 1993Google Scholar
  2. 2.
    N.J. Simon, E.S. Drexler and R.P. Reed. “Shear/Compressive Tests For ITER Magnet Insulation”. Adv. Cry. Eng. (Materials) Vol. 40, Plenum Press, New York, 1994.Google Scholar
  3. 3.
    J.B. Schultz and R.P. Reed, “Inorganic and Hybrid Insulation For ITER”. Adv. Cry. Eng. (Materials) Vol. 40, Plenum Press, New York, 1994.Google Scholar
  4. 4.
    T. Nishijura, S. Nishijima and T. Okada. “Synergistic Effects of Radiation and Stress on Mechanical Properties of Organic and Composite Materials”. Cryogenics, Vol. 35 (1995) No. 11, pp 747–749CrossRefGoogle Scholar
  5. 5.
    T. Nishijura, S. Nishijima and T. Okada. “Effects of Synergistic Irradiation and Stress on FRP at Cryogenic Temperatures”. Adv. Cry. Eng. (Materials) 40, 1035–1042 (1994)Google Scholar
  6. 6.
    H. Gerstenberg, E. Krahling, H. Katheder and M. Soll. “Reactor Irradiations at Temperatures Below 6 K”. Adv. Cry. Eng. (Materials) Volume 40, Plenum Press, New York. 1994Google Scholar
  7. 7.
    W. Maurer. “Neutron and Gamma Erradiation Effects on Organic Insulating Materials for Fusion Magnets”. Institut fur Technische Physik, Karlsruhe GmbH. KfK 3974 (1983).Google Scholar
  8. 8.
    R.P. Reed, et al. Shear “Strength of Irradiated Insulation Under Combined Shear/Compression Loading”. Adv. Cry. Eng. (Materials) Vol. 42, Plenum Press. New York. 1995.Google Scholar

Copyright information

© Springer Science+Business Media New York 1998

Authors and Affiliations

  • D. Evans
    • 1
  • R. P. Reed
    • 2
  1. 1.Rutherford Appleton LaboratoryUK
  2. 2.Cryogenic Materials Inc.USA

Personalised recommendations