Advertisement

Effect of an 8 Tesla Magnetic Field on Mechanical Properties of Incoloy 908 Alloy at 4K

  • T. Kadota
  • T. Tanaka
  • Y. Kohno
  • H. Nakajima
  • H. Tsuji
  • K. Shibata
Part of the Advances in Cryogenic Engineering book series (ACRE, volume 44)

Abstract

Tensile tests were performed using specimens of 3mm thickness. Fracture toughness tests were carried out on half size specimens. These specimens were machined from a hot rolled 28mm thick plate. After the effects of an 8 tesla magnetic field were calibrated, clip-on gauges were used in these tests. Effects of the magnetic field on 0.2% proof strength, tensile strength, elongation, Young’s modulus, serration and fracture toughness were examined. The application of the magnetic field showed no noticeable effect on tensile properties whereas increases in Young’s modulus and tearing modulus were observed in the magnetic field. The magnetic effect on serrated flow was not clear because amplitude and frequency of the serration of this alloy are too small. The reason for this small serration was discussed using computer simulation by comparing with the serration observed in high strength austenitic stainless steel YUS170 which has a similar strength level at 4K.

Keywords

Magnetic Field Fracture Toughness Austenitic Stainless Steel Fracture Toughness Test Japan Atomic Energy Research Institute 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    I.S. Hwang. R.G. Ballinger, M.M. Morra and M.M. Steeves, Mechanical Properties of Incoloy 908 -An Update, Advances in Cryogenic Engineering Materials, vol.38, Plenum, New York (1992), 1.Google Scholar
  2. 2.
    R.M. Bozorth. “Ferromagnetism”, Van Nostrand, New York, (1951), 684.Google Scholar
  3. 3.
    T. Shimonosono, Y. Kurita and K. Shibata, Effects of High Magnetic Field on Fracture Toughness of SUS304L Steel at 4K, Annual Report of the Eng. Research Institute Fac. of Eng., Univ. of Tokyo, (1993), vol. 52, 141.Google Scholar
  4. 4.
    K. Shibata, H. Sakamoto, K, Fujita and T. Fujita, Computer Simulation of Serration near Liquid Helium Temperatures, Advances in Cryogenic Engineering Materials, vol.34, Plenum, New York (1988), 217.Google Scholar
  5. 5.
    Unpublished data book of JAERI.Google Scholar
  6. 6.
    Handbook of Materials for Superconducting Machinery“, NBS(1977).Google Scholar
  7. 7.
    T. Ogata, K. Nagai, K. Ishikawa, K. Shibata and E. Fukushima, VAMAS Second Round Robin Test of Structural Materials at Liquid Helium Temperature, Advances in Cryogenic Engineering Materials, vol.38, Plenum, New York (1992), 69.Google Scholar
  8. 8.
    K, Shibata, E. Naito, H. Sakamoto and K. Fujita, Adiabatic Deformation of Austenitic Stainless Steel Sheet Near Absolute Zero, Progress in High Temperature Superconductivity, ed. by Y. Murakami, World Scientific, Singapore, (1989), vol. 15, 486.Google Scholar

Copyright information

© Springer Science+Business Media New York 1998

Authors and Affiliations

  • T. Kadota
    • 1
  • T. Tanaka
    • 1
  • Y. Kohno
    • 2
  • H. Nakajima
    • 3
  • H. Tsuji
    • 3
  • K. Shibata
    • 2
  1. 1.Graduate school student. Dept. of Materials ScienceThe University of TokyoBunkyo-ku, Tokyo 113Japan
  2. 2.Department of Materials ScienceThe University of TokyoBunkyo-ku, Tokyo 113Japan
  3. 3.Super Conducting Magnet LaboratoryJapan Atomic Energy Research InstituteNaka-machi, Naka-gun, Ibaragi Prefecture 305Japan

Personalised recommendations