Advertisement

Materials pp 331-338 | Cite as

Scaling Tests on Smooth and Notched Specimens of Polyimide (SINTIMID) at Cryogenic Temperatures

  • Karl Humer
  • Harald W. Weber
  • Elmar K. Tschegg
Part of the Advances in Cryogenic Engineering book series (ACRE, volume 38)

Abstract

Because of applications in space and in cryogenic equipment, such as superconducting magnets, the mechanical properties and in some cases the radiation tolerance of various types of plastics have to be assessed. In the present contribution, we report on tensile strength experiments on a polyimide (SINTIMID) carried out at room temperature, 77 K and 4.2 K. Special attention was paid to “scaling” experiments, where the influence of sample size (scaled down from DIN and ASTM standards) on the elastic modulus, the ultimate tensile strength (UTS) and the failure strain was investigated. In addition, the influence of sample size on the mechanical properties in mode I have been investigated on cylindrical pre-cracked samples with a circumferential notch. The results of the tensile tests show that a variation of the sample size does not affect the UTS. Concerning the test temperature, the results show an increase of both the elastic modulus and the UTS by 40% and 60%, respectively, when decreasing the temperature to 77 K, but no further change at 4.2 K, while the failure strain decreases continuously (by about 25%) when cooling down to 4.2 K. Regarding the fracture tests no sample size dependence of the fracture properties could be detected. The fracture toughness increases continuously by about 10% with decreasing test temperature down to 4.2 K. The results will be discussed and compared with data on other materials. Additional fractographic investigations show no significant dependence of the fracture surfaces on the sample size for both the tensile and the fracture test samples.

Keywords

Fracture Surface Fracture Toughness Ultimate Tensile Strength Failure Strain Sample Geometry 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    P. C. Michael, D. Aized, E. Rabinowicz and I. Iwasa, Mechanical properties and static friction behaviour of epoxy mixes at room temperature and at 77 K, Cryogenics 30: 775–786 (1990).CrossRefGoogle Scholar
  2. 2.
    G. Hartwig, B. Kneifel and K. Pöhlmann, Fracture properties of polymers and composites at cryogenic temperatures, Adv. Cryog. Eng. 32: 169–177 (1986).CrossRefGoogle Scholar
  3. 3.
    G. Hartwig and K. Pöhlmann, Low temperature fracture strain at high deformation rates, Adv. Cryog. Eng. 30: 83–88 (1984).CrossRefGoogle Scholar
  4. 4.
    R. R. Coltman, jr. and C. E. Klabunde, Mechanical strength of lowtemperature-irradiated polyimides: A five-to-tenfold improvement in dose-resistance over epoxies, J. Nucl. Mat. 103 /104: 717–721 (1981).CrossRefGoogle Scholar
  5. 5.
    S. Nishijima, S. Ueta and T. Okada, The effects of low temperature irradiation effect on the cryogenic fatigue resistance of epoxy resin used in superconducting magnets, Cryogenics 21: 312–313 (1981).CrossRefGoogle Scholar
  6. 6.
    H. W. Weber and E. K. Tschegg, Test program for mechanical strength measurements on fiber reinforced plastics exposed to radiation environments, Adv. Cryog. Eng. 36: 863–869 (1990).Google Scholar
  7. 7.
    M. B. Kasen, Cryogenic properties of filamentary-reinforced composites: an update, Cryogenics 21: 323–340 (1981).CrossRefGoogle Scholar
  8. 8.
    E. K. Tschegg, K. Humer and H. W. Weber, Influence of test geometry on tensile strength of fibre reinforced plastics at cryogenic temperatures, Cryogenics 31: 312–318 (1991).CrossRefGoogle Scholar
  9. 9.
    E. K. Tschegg, E. Kubasta and W. Steiner, A top loading 200kN tensile testing cryostat, Cryogenics 19: 269–271 (1979).CrossRefGoogle Scholar
  10. 10.
    E. K. Tschegg, K. Humer and H. W. Weber, Mechanical properties and fracture behavior of polyimide (SINTIMID) at cryogenic temperatures, Cryogenics (in press).Google Scholar
  11. 11.
    Y. Murakami, Soc.Mat.Sci.Jap., Stress intensity factors handbook, Vol. 2: 643 (1987).Google Scholar
  12. 12.
    J. A. Hinkley and S. L. Mings, Fracture toughness of polyimide films, Polymer 31: 75–77 (1990).CrossRefGoogle Scholar
  13. 13.
    M. J. Zhang and F. X. Zhi, Crack growth mechanism in some polyamides, Polymer 29: 2152–2158 (1988).CrossRefGoogle Scholar
  14. 14.
    K. L. De Vries and L. E. Hornberger, Macroscopic, microscopic and molecular aspects of fracture in polymers, Polymer Degredation and Stability 24: 213–240 (1989).CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media New York 1992

Authors and Affiliations

  • Karl Humer
    • 1
  • Harald W. Weber
    • 1
  • Elmar K. Tschegg
    • 2
  1. 1.Atominstitut der Österreichischen UniversitätenWienAustria
  2. 2.Institut für Angewandte und Technische PhysikTechnische UniversitätWienAustria

Personalised recommendations