BER Performance of Adaptive RAKE Receiver Using Tap Weights Obtained by POCS Deconvolution Technique
The RAKE receiver is used in the multipath channels to make use of the inherent time-diversity effect achieved by the use of a direct sequence spread spectrum (DSSS) communication system. Coherent combining of multipath signals by a RAKE receiver improves system performance. The improvement in performance is based on selecting the stronger paths and rejecting the noisy or weak paths. This criterion requires good estimates of the multipath channel parameters. We obtain multipath parameter estimates by the set theoretic deconvolution technique. The method is based on the constrained iterative deconvolution using the method of Projection Onto Convex Sets (POCS). In this paper we analyze the bit error rate (BER) performance of an adaptive RAKE receiver by computer simulations for a BPSK/DSSS system in an indoor environment. The performance is analyzed for indoor multipath channel models, with/without Inter Symbol Interference (ISI). In order to have a realistic effect, we generate the impulse response of the channels by software package SIR CIM.
For comparison purposes, performance of five receivers was analyzed, i. e., Strongest Path (SP), RAKE with ideal estimates (Ideal), Post Detection Integrator (PDI), RAKE with matched filter estimates (MF), and RAKE with POCS estimates. The simulation results show that the RAKE receiver with tap weights being adjusted by POCS estimates performs close to an ideal RAKE for a sounding signal transmitted at Signal to Noise Ratio (SNR) of greater than 25 dB. It performs about 1–2 dB better than the RAKE with matched filter estimates at BER of 10-3. The performance being superior at low sounding SNR. It was also observed that performance of a PDI receiver was extremely poor, i.e. a simple implementation of RAKE receiver in an indoor multipath environment, having large number of taps and small number of useful paths is not feasible.
KeywordsImpulse Response Matched Filter Channel Impulse Response Multipath Channel Rake Receiver
Unable to display preview. Download preview PDF.
- 1.R. Price et al, A communication technique for multipath channels, Proc. IRE, March 1958, pp. 555–570.Google Scholar
- 2.J. G. Proakis, Digital Communications, 2nd ed., McGraw-Hill, New York, 1989.Google Scholar
- 4.H. J. Trussell et al., The feasible solution in signal restoration, IEEE Trans. ASSP, vol. 32, no. 2, April 1984.Google Scholar
- 5.Z. Kostić et al., Estimation of parameters of a multipath channel using set-theoretic deconvolution, IEEE Trans. Commun., vol. 40, no. 6, June 1992.Google Scholar
- 6.Z. Kostić et al., Resolving sub-chip spaced multipath components in CDMA communication systems, Proc. IEEE VTC, 1993, pp. 428–431.Google Scholar
- 7.S. Hussain, Estimating complex impulse response of a multipath channel using POCS deconvolution, WINLAB Internal Report, Rutgers, The State University, Oct. 1992 and Jan. 1993.Google Scholar
- 8.T. S. Rappaport et al., SIRCIM: simulation of indoor radio impulse response models, 1990, VTIP Inc.Google Scholar
- 9.C. N. Pateros et al., Adaptive correlator receiver performance in fading multipath channels, Proc. IEEE VTC, 1993, pp. 746–749.Google Scholar
- 10.Y. Sanada et al., Adaptive RAKE system for mobile communications, IEEE Intl. Conf. on Selected Topics in Wireless Communications, Vancouver, Canada, June 1992, pp. 227–230.Google Scholar
- 11.P. M. Grant et al., Performance of a spread spectrum receiver design, IEEE 2nd Intl. Symp. on Spread Spectrum Techniques and Applications, Yokahoma, Japan, Nov. 1992.Google Scholar
- 12.P. A. Bello, Performance of some RAKE modems over the non-disturbed wide band HF channel, IEEE Mil. Commun. Conf., San Diego, California, Oct. 1988, pp. 89–95.Google Scholar