Advertisement

A Coupled Thermal-Structural Model for Welding of Aluminium Alloy Sheets

  • Tapas BajpaiEmail author
  • H. Chelladurai
  • M. Zahid Ansari
Conference paper
Part of the Lecture Notes on Multidisciplinary Industrial Engineering book series (LNMUINEN)

Abstract

Computational simulations using the finite element method are advantageous in predicting the response of the weldments during the welding processes. These welding simulations help in ensuring the correction in the process design to compensate for the effects of the welding before the commencement of the actual fabrication process. In this work, a coupled thermo-mechanical finite element model is presented for simulating the gas metal arc welding process on thin aluminium alloy plates. For modelling the thermal and mechanical behaviour of the weldments, finite element ANSYS software is used. Temperature-dependent properties of plates are used in the simulation. Effects of conduction and convection due to air and argon gas are considered. For modelling the welding heat source, Goldak’s double ellipsoidal heat flux distribution is implemented. With the help of finite element solutions, transient temperature and transient stress distribution in aluminium alloy weldments are estimated.

Keywords

Aluminium alloy (AA) Finite element modelling (FEM) Heat-affected zone (HAZ) 

References

  1. 1.
    Bajpei, T., Chelladurai, H., Ansari, M.Z.: Mitigation of residual stresses and distortions in thin aluminium alloy GMAW plates using different heat sink models. J. Manuf. Process. 22, 199–210 (2016)CrossRefGoogle Scholar
  2. 2.
    Bajpei, T., Chelladurai, H., Ansari, M.Z.: Experimental investigation and numerical analyses of residual stresses and distortions in GMA welding of thin dissimilar AA5052–AA6061 plates. J. Manuf. Process. 25, 340–350 (2017).  https://doi.org/10.1016/j.jmapro.2016.12.017CrossRefGoogle Scholar
  3. 3.
    Bajpei, T., Chelladurai, H., Ansari, M.Z.: Numerical investigation of transient temperature and residual stresses in thin dissimilar aluminium alloy plates. Procedia Manuf. 5, 558–567 (2016).  https://doi.org/10.1016/j.promfg.2016.08.046CrossRefGoogle Scholar
  4. 4.
    Zhu, X., Chao, Y.: Effects of temperature dependent material properties on welding simulation. Comput. Struct. 80, 967–976 (2002)CrossRefGoogle Scholar
  5. 5.
    Bhatti, A.A., Barsoum, H., Murakawa, I., Barsoum, I.: Influence of thermo-mechanical material properties of different steel grades on welding residual stresses and angular distortion. Mater. Des. 65, 878–889 (2015)CrossRefGoogle Scholar
  6. 6.
    Kumaresan, D., Asraff, A.K., Muthukumar, R.: Numerical investigation on heat transfer and residual stress in butt welded plate. J. Pressure Vessel Technol. 133, 1–10 (2011)CrossRefGoogle Scholar
  7. 7.
    Mi, G., Wei, Y., Zhan, X., Gu, C., Yu, F.: A coupled thermal and metallurgical model for welding simulation of Ti–6Al–4V alloy. J. Mater. Process. Technol. 214, 2434–2443 (2014)CrossRefGoogle Scholar
  8. 8.
    Incropera, F., Dewitt, D., Bergman, T., Lavine, A.: Fundamentals of Heat and Mass Transfer. Wiley, U.K. (2007)Google Scholar
  9. 9.
    Goldak, J., Chakravarti, A., Bibby, M.: A new finite element model for welding heat sources. Metall. Trans. B 15, 299–305 (1984)CrossRefGoogle Scholar
  10. 10.
    Goldak, J., Akhlaghi, M.: Computational Welding Mechanics. Springer Science + Business Media Inc., New York (2005)Google Scholar
  11. 11.
    Kou, S.: Welding Metallurgy. Wiley, New Jersey (2003)Google Scholar
  12. 12.
    ANSYS Mechanical APDL Advanced Analysis Guide/ANSYS help (2013), release 15.0, Canonsburg, USAGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2020

Authors and Affiliations

  1. 1.Department of Mechanical EngineeringMalaviya National Institute of TechnologyJaipurIndia
  2. 2.Mechanical Engineering DisciplinePDPM Indian Institute of Information Technology, Design and ManufacturingJabalpurIndia

Personalised recommendations