Advertisement

Microstructural Evaluation of Friction Surfaced Aluminium Alloy AA6063 Over Mild Steel

  • B. Vijaya KumarEmail author
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

AA6063 aluminium alloy coating was deposited over IS2062 mild steel using friction surfacing technique and the microstructural evaluation was studied at various process parametric combinations to obtain relationships between the input parameters and grains interlocking which were observed from microstructural evaluation and with microhardness. The microstructural evaluation of the coating images across the interface using microstructure image analyzer and hardness was also measured across the interface using micro Vickers hardness. Studies revealed that no defect along the interface and very good bond integrity between aluminium alloy and mild steel. Coating exhibited fine grain size microstructure along the interface. It is noticed that aluminium alloy layers are cohesive with mild steel and coating layers dovetailed with base metal which is required for interface strength. Mechtrode rotational speed (N), axial load (F) Table speed (Vx) are noteworthy elements and influence the output parameters. Based on the observation of results more metal transfer at the parametric combination of higher axial load and traverse speed with lower rotational speed produced sound coating. Based on various ranges of parameters, combination of strong bond is obtained in a close range of parameters’ combination. Coating metal and base metal are incongruous and have propensity to form brittle inter-metallics

Keywords

Friction surfacing Mechtrode Substrate Microstructure Sound coating 

Notes

Acknowledgements

The authors are thankful to the authorities of Defence Metallurgical Research Laboratory for providing the friction surfacing facilities to carry out the experiments. They would also like to place on record the support extended by Mr. G. Vijay Kumar for his help in carrying out friction surfacing experiments and Mr. D. S. K. Murali in carrying out the mechanical testing.

References

  1. 1.
    Tokisue H, Katoh K (2005) Structure and mechanical properties of multilayer friction surfaced aluminium alloys. Report of the Research Institute of Industrial Technology. Nihon University, Number 78Google Scholar
  2. 2.
    Chandrasekaran M, Batchelor AW (1997) Study of the interfacial phenomena during friction surfacing of aluminum with steel. J Mater Sci 32:6055–6062CrossRefGoogle Scholar
  3. 3.
    Li JQ, Shinoda T (2000) Underwater friction surfacing. Surf Eng 16(1):31–35 CrossRefGoogle Scholar
  4. 4.
    Klopstock H, Neelands AR (1941) An improved method of joining and welding metals. U.K. Patent No. 572, 789, 17 October 1941Google Scholar
  5. 5.
    Sakihama H, Tokisue H (2002) Mechanical properties of friction surfaced 5052 aluminium alloy. J Jpn Inst Light Metals 52(8):346–351CrossRefGoogle Scholar
  6. 6.
    Shinoda T, Okamoto S (1995) Deposition of hard coating layer by friction surfacing. J Jpn Weld Soc 13(3):432–437 (1995-08-05)CrossRefGoogle Scholar
  7. 7.
    Madhusudhan Reddy G, Srinivasa Rao K, Mohandas T (2009) Friction surfacing: novel technique for metal matrix composite coating on aluminium-silicon alloy. Surf Eng 25(1):25–30 CrossRefGoogle Scholar
  8. 8.
    Vitanov VI, Voutchkov II (2005) Process parameters selection for friction surfacing applications using intelligent decision support. J Mater Process Technol 159:27–32CrossRefGoogle Scholar
  9. 9.
    Chandrasekaran M, Batchelor AW (1997) Friction surfacing of metal coatings on steel and aluminium substrate. J Mater Process Technol 72:446–452CrossRefGoogle Scholar
  10. 10.
    Batchelor AW, Jana S (1996) The effect of metal type and multi layering on friction surfacing. J Mater Process Technol 57:172–181CrossRefGoogle Scholar
  11. 11.
    Khalid Rafi H, Janaki Ram GD, Phanikumar G, Prasad Rao K (2010) Friction surfacing of Austenitic stainless steel on low carbon steel: studies on the effect of traverse speed. In: Proceedings of the World Congresson Engineering 2010, vol II, WCE, London, 30 June–2 July 2010 Google Scholar
  12. 12.
    Liu XM, Zou ZD, Zhang YH, Qu SY, Wang XH (2008) Transferring mechanism of the coating rod in friction surfacing. Surf Coat Technol 202(9):1889–1894CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2020

Authors and Affiliations

  1. 1.Department of Mechanical EngineeringGuru Nanak Institute of TechnologyIbrahimpatnamIndia

Personalised recommendations