Advertisement

Experimental Comparative Study on Strength Parameters of Concrete Assimilating Glass Fibers of Fine Aggregate, Cement with Rubber and GGBS

  • Arjun Sil
  • Naveen Kumar VanapalliEmail author
  • Anisha Kumari
  • Pratyasha Gogoi
  • Debasish Mojumder
Conference paper
Part of the Lecture Notes in Civil Engineering book series (LNCE, volume 55)

Abstract

The utilization of fibers and waste materials from industry in concrete is making a remarkable change in properties of concrete. For the present study a comparison of effectiveness in strength properties when rubber, GGBS and silica fumes are used as a substitute for fine aggregate and cement respectively and alkali-resistant glass fibers are added in concrete. The effect of addition or replacement of fibers and materials on strength parameters are studied. Fine aggregate is replaced with crumb rubber and cement is also replaced with GGBS in addition to Silica fumes, as required target strength is not attained when fine aggregate is replaced with rubber. A maximum of 30% of replacement of rubber is done, depending upon the results, it is known that replacement of rubber should be restricted and low w/c ratios should be adopted. Simultaneously, in another mix glass fibers are added to plain concrete in varying percentages, maximum of 1.5%. It is observed that the use of glass fibers in concrete mixes increases tensile strength without affecting its compressive strength, thus making it beneficial to use glass fibers as there is significant increase in strength. Depending upon the percentage of replacement and addition six trial, mixes are adopted. The strength comparison is done between the six trial mixes with nominal mix of grade M25 and are presented here.

Keywords

Crumb rubber GGBS Silica fumes Fibres Strength parameters 

Notes

Acknowledgements

This work is mainly carried out receiving the financial support from the DST-SERB, GOI under sanction no. ECR/2016/001329.

References

  1. 1.
    Scrap Tires: Deflating a Growing Problem (1988) Compressed air magazineGoogle Scholar
  2. 2.
    Thomas BS, Gupta RC, Vinu JP (2016) Recycling of waste tire rubber as aggregate in concrete: durability-related performance. J Clean Prod 112(1):504–513CrossRefGoogle Scholar
  3. 3.
    Shariq M, Prasad J, Masood A (2010) Effect of GGBFS on time dependent compressive strength of concrete. J Constr Build Mater 24(8):1469–1478CrossRefGoogle Scholar
  4. 4.
    Wroblewskia L, Hristozova D, Sadeghianb P (2016) Durability of bond between concrete beams and FRP composites made of flax and glass fibers. J Constr Build Mater 126(15):800–811CrossRefGoogle Scholar
  5. 5.
    Dawood ET, Mezal AM (2014) The properties of fiber reinforced gypsum plaster. J Sci Res Rep 3(10):1339–1347CrossRefGoogle Scholar
  6. 6.
    Concrete and Aggregate (1988) Annual book of ASTM standards, vol 04.02, ASTM, Philadelphia, PAGoogle Scholar
  7. 7.
    Guidelines for Using Recycled Tire Carcasses in Highway Maintenance (1987) Office of Transportation Laboratory, California Department of Transportation, Sacramento, CaliforniaGoogle Scholar
  8. 8.
    Payne AR, Scott JR (1960) The properties, testing and design of rubber as an engineering material. Inter-science Publishers, New York, N.Y.Google Scholar
  9. 9.
    Popovics S (1987) A hypothesis concerning the effects of macro-porosity on mechanical properties of concrete. In: Proceedings of the SEM/RELIM international conference on fracture of concrete and rock. Springer, New York, pp 170–174CrossRefGoogle Scholar
  10. 10.
    Grade Ordinary Portland Cement (1989) IS 8112—Bureau of Indian Standard, New DelhiGoogle Scholar
  11. 11.
    Code for Concrete Mix Proportioning (2009) IS 10262—Bureau of Indian Standard, New DelhiGoogle Scholar
  12. 12.
    Plain and Reinforced Concrete Code or Practice (Fourth Revision) (2000) IS 456—Bureau of Indian Standard, New DelhiGoogle Scholar
  13. 13.
    Specification for Coarse and Fine Aggregate from Natural Sources for Concrete (Second Revision) (1970) IS 383—Bureau of Indian Standard, New DelhiGoogle Scholar
  14. 14.
    Indian Standard Concrete Admixture Specification (1999) IS 9103—Bureau of Indian Standard, New DelhiGoogle Scholar
  15. 15.
    Methods of Tests for Strength of Concrete (1959) IS 516—Bureau of Indian Standard, New DelhiGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2020

Authors and Affiliations

  • Arjun Sil
    • 1
  • Naveen Kumar Vanapalli
    • 1
    Email author
  • Anisha Kumari
    • 1
  • Pratyasha Gogoi
    • 1
  • Debasish Mojumder
    • 1
  1. 1.Department of Civil EngineeringNIT SilcharSilcharIndia

Personalised recommendations