Advertisement

Carbon Nanotubes Synthesized by Green/Eco-friendly Technique Potential for Bioenergy Applications

  • Kelvii Wei Guo
Chapter
  • 25 Downloads
Part of the Clean Energy Production Technologies book series (CEPT)

Abstract

The multi-walled carbon nanotubes (MWCNTs) were synthesized by homemade equipment with the waste alcohol. The synthesized MWCNTs were characterized by scanning electron microscopy (SEM), transmission electron microscope (TEM), and Raman spectroscopy. Moreover, in confirming the synthesized green/eco-friendly technique, MWCNTs were grown on some of the micropunches to show the attractive potential for bioenergy application compellingly and convincingly. Results show that due to the usage of the waste alcohol, not only is this technique definitely green/eco-friendly to the environment, but also MWCNTs as a protective layer on the micropunch can lengthen the service life of the micropunch by up to 35% without directly affecting the size of the punched holes compared with that of without MWCNTs. Moreover, the punched microholes are definitely quite distinct from that of traditional punching. Besides the fracture band is absent, the areas of rollover and burr are also extremely narrow, which implies the attractive punched microhole can be used directly without any posttreatments.

Keywords

Multi-walled carbon nanotubes (MWCNTs) Green/eco-friendly technique Bioenergy Biomass power plant Waste alcohol Nanotechnology Microhole Micropunch Service life 

References

  1. Abed WM, Domingues AF, Poole RJ, Dennis DJC (2017) Heat transfer enhancement in a cross-slot micro-geometry. Int J Therm Sci 121:249–265CrossRefGoogle Scholar
  2. Affes F, Ketata H, Kharrat M, Dammak M (2018) How a pilot hole size affects osteosynthesis at the screw-bone interface under immediate loading. Med Eng Phys 60:14–22CrossRefGoogle Scholar
  3. Ali ARA, Janajreh I (2015) Numerical simulation of turbine blade cooling via jet impingement. Energy Procedia 75:3220–3229CrossRefGoogle Scholar
  4. Ali A, Khan ZS, Jamil M, Khan Y, Ahmad N, Ahmed S (2018) Simultaneous reduction and sulfonation of graphene oxide for efficient hole selectivity in polymer solar cells. Curr Appl Phys 18(5):599–610CrossRefGoogle Scholar
  5. Al-Zurfi N, Turan A (2016) LES of rotational effects on film cooling effectiveness and heat transfer coefficient in a gas turbine blade with one row of air film injection. Int J Therm Sci 99:96–112CrossRefGoogle Scholar
  6. Amirante R, Distaso E, Tamburrano P (2014) Experimental and numerical analysis of cavitation in hydraulic proportional directional valves. Energy Convers Manag 87:208–219CrossRefGoogle Scholar
  7. Asim T, Mishra R, Oliveira A, Charlton M (2019) Effects of the geometrical features of flow paths on the flow capacity of a control valve trim. J Pet Sci Eng 172:124–138CrossRefGoogle Scholar
  8. Baghel R, Mali HS (2018) A study on effects of discharge energy on geometric characteristics of high aspect ratio micro-holes on TiN-Al2O3 ceramics. Mater Today Proc 5(9, Part 3):17828–17837CrossRefGoogle Scholar
  9. Baik KD, Seo IS (2018) Metallic bipolar plate with a multi-hole structure in the rib regions for polymer electrolyte membrane fuel cells. Appl Energy 212:333–339CrossRefGoogle Scholar
  10. Baino F, Potestio I (2016) Orbital implants: state-of-the-art review with emphasis on biomaterials and recent advances. Mater Sci Eng C 69:1410–1428CrossRefGoogle Scholar
  11. Bakshi SR, Keshri AK, Agarwal A (2011) A comparison of mechanical and wear properties of plasma sprayed carbon nanotube reinforced aluminum composites at nano and macro scale. Mater Sci Eng A 528:3375–3384CrossRefGoogle Scholar
  12. Banyai D, Sfarlea I, Opruta D (2016) Experimental research on variable hydraulic resistors of servo-hydraulic valves. Energy Procedia 85:44–51CrossRefGoogle Scholar
  13. Belarb E, Blas-Ferrando VM, Haro M, Maghraoui-Meherzi H, Gimenez S (2016) Electropolymerized polyaniline: a promising hole selective contact in organic photoelectrochemical cells. Chem Eng Sci 154:143–149CrossRefGoogle Scholar
  14. Bellemère P (2018) Pyrocarbon implants for the hand and wrist. Hand Surg Rehab 37(3):129–154CrossRefGoogle Scholar
  15. Bhattacharya R (2018) Generation of phase singular optical beams in microstructure optical fibers. Opt Commun 428:15–21CrossRefGoogle Scholar
  16. Bhattacharyya B (2015) Chapter 12. Recent advancements in EMM for micro and nanofabrication. In: Electrochemical micromachining for nanofabrication, MEMS and nanotechnology, pp 219–240Google Scholar
  17. Biasetti DA, Di Liscia EJ, Torchia GA (2017) Optical waveguides fabricated in Cr:LiSAF by femtosecond laser micromachining. Opt Mater 73:25–32CrossRefGoogle Scholar
  18. Block MS (2018) Dental implants: the last 100 years. J Oral Maxillofac Surg 76(1):11–26CrossRefPubMedPubMedCentralGoogle Scholar
  19. Boncel S, Müller KH, Skepper JN, Walczak KZ, Koziol KKK (2011) Tunable chemistry and morphology of multi-wall carbon nanotubes as a route to non-toxic, theranostic systems. Biomaterials 32:7677–7686CrossRefPubMedPubMedCentralGoogle Scholar
  20. Brousseau EB, Dimov SS, Pham DT (2010) Some recent advances in multi-material micro- and nano-manufacturing. Int J Adv Manuf Technol 47:161–180CrossRefGoogle Scholar
  21. Calabriso A, Cedola L, Zotto LD, Rispoli F, Santori SG (2015) Performance investigation of passive direct methanol fuel cell in different structural configurations. J Clean Prod 88:23–28CrossRefGoogle Scholar
  22. Calvo-López A, Puyol M, Casalta JM, Alonso-Chamarro J (2017) Multi-parametric polymer-based potentiometric analytical microsystem for future manned space missions. Anal Chim Acta 995:77–84CrossRefPubMedPubMedCentralGoogle Scholar
  23. Chavoshi SZ, Luo XC (2015) Hybrid micro-machining processes: a review. Precis Eng 41:1–23CrossRefGoogle Scholar
  24. Cherevko S, Kulyk N, Mayrhofer KJJ (2016) Durability of platinum-based fuel cell electrocatalysts: dissolution of bulk and nanoscale platinum. Nano Energy 29:275–298CrossRefGoogle Scholar
  25. Choi YJ, Oh EK, Lee MJ, Kim NJ, Choung HY, Khwarg SI (2018) Atypical mycobacterial infection in anophthalmic sockets with porous orbital implant exposure. Am J Ophthalmol 195:131–142CrossRefPubMedPubMedCentralGoogle Scholar
  26. Christwardana M, Frattini D, Accardo G, Yoon SP, Kwon YC (2018) Early-stage performance evaluation of flowing microbial fuel cells using chemically treated carbon felt and yeast biocatalyst. Appl Energy 222:369–382CrossRefGoogle Scholar
  27. Chung H, Park JS, Sohn HS, Rhee DH, Cho HH (2014) Trailing edge cooling of a gas turbine blade with perforated blockages with inclined holes. Int J Heat Mass Transf 73:9–20CrossRefGoogle Scholar
  28. Cole KM, Kirk DW, Singh CV, Thorpe SJ (2017) Optimizing electrochemical micromachining parameters for Zr-based bulk metallic glass. J Manuf Process 25:227–234CrossRefGoogle Scholar
  29. Cortes DF, Tang TX, Capelluto DGS, Lazar IM (2017) Nanoflow valve for the removal of trapped air in microfluidic structures. Sensors Actuators B Chem 243:650–657CrossRefGoogle Scholar
  30. Cristofari F, Piotrowski B, Pesci R (2017) Mechanical properties of a nanoporous membrane used in implantable medical devices. Correlation between experimental characterization and 2D numerical simulation. J Mech Behav Biomed Mater 74:43–53CrossRefGoogle Scholar
  31. Damnjanović M, Vuković T, Milosević I (2002) Super-slippery carbon nanotubes: symmetry breaking breaks friction. Eur Phys J B 25:131–134CrossRefGoogle Scholar
  32. De Volder MF, Tawfick SH, Baughman RH, Hart AJ (2013) Carbon nanotubes: present and future commercial applications. Science 339:535–539CrossRefGoogle Scholar
  33. de Vries SF, Florea D, Homburg FGA, Frijns AJH (2017) Design and operation of a tesla-type valve for pulsating heat pipes. Int J Heat Mass Transf 105:1–11CrossRefGoogle Scholar
  34. Derkus B (2016) Applying the miniaturization technologies for biosensor design. Biosens Bioelectron 79:901–913CrossRefGoogle Scholar
  35. di Capaci RB, Vaccari M, Pannocchia G (2018) Model predictive control design for multivariable processes in the presence of valve stiction. J Process Control 71:25–34CrossRefGoogle Scholar
  36. Dickrell PL, Sinnott SB, Hahn DW, Raravikar NR, Schadler LS, Ajayan PM, Sawyer WG (2005) Frictional anisotropy of oriented carbon nanotube surfaces. Tribol Lett 18(1):59–62.  https://doi.org/10.1007/s11249-004-1752-0CrossRefGoogle Scholar
  37. Dickrell PL, Pal SK, Bourne GR, Muratore C, Voevodin AA, Ajayan PM, Schadler LS, Sawyer WG (2006) Tunable friction behavior of oriented carbon nanotube films. Tribol Lett 24(1):85–90CrossRefGoogle Scholar
  38. Dittmeyer R, Boeltken T, Piermartini P, Selinsek M, Loewert M, Dallmann F, Kreuder H, Cholewa M, Wunsch A, Belimov M, Farsi S, Pfeifer P (2017) Micro and micro membrane reactors for advanced applications in chemical energy conversion. Curr Opin Chem Eng 17:108–125CrossRefGoogle Scholar
  39. Do KH, Kim T, Han YS, Choi BI, Kim M (2017) Investigation on flow distribution of the fuel supply nozzle in the annular combustor of a micro gas turbine. Energy 126:361–373CrossRefGoogle Scholar
  40. Dornfeld D, Min S, Takeuchi Y (2006) Recent advances in mechanical micromachining. CIRP Ann Manuf Technol 55(2):745–768CrossRefGoogle Scholar
  41. Dubois A, Ricote S, Braun RJ (2017) Benchmarking the expected stack manufacturing cost of next generation, intermediate-temperature protonic ceramic fuel cells with solid oxide fuel cell technology. J Power Sources 369:65–77CrossRefGoogle Scholar
  42. Dupuis AC (2005) The catalyst in the CCVD of carbon nanotubes – a review. Prog Mater Sci 50:929–961CrossRefGoogle Scholar
  43. Dvořák M, Seip KF, Pedersen-Bjergaard S, Kubáň P (2018) Semi-automated set-up for exhaustive micro-electromembrane extractions of basic drugs from biological fluids. Anal Chim Acta 1005:34–42CrossRefGoogle Scholar
  44. Edvardsen S, Dorao CA, Nydal OJ (2015) Multiphase flow in complex valve geometry. Energy Procedia 64:91–100CrossRefGoogle Scholar
  45. Edwards SA (2006) The nanotech pioneers. Angew Chem 45(43):7116–7117CrossRefGoogle Scholar
  46. Enagi II, Al-attab KA, Zainal ZA (2017) Combustion chamber design and performance for micro gas turbine application. Fuel Process Technol 166:258–268CrossRefGoogle Scholar
  47. Farzaneh-Gord M, Khoshnazar H (2016) Valve fault detection for single-stage reciprocating compressors. J Nat Gas Sci Eng 35(Part A):1239–1248CrossRefGoogle Scholar
  48. Ferraris S, Spriano S (2016) Antibacterial titanium surfaces for medical implants. Mater Sci Eng C 61:965–978CrossRefGoogle Scholar
  49. Ferraro D, Serra M, Ferrante I, Viovy JL, Descroix S (2018) Microfluidic valve with zero dead volume and negligible back-flow for droplets handling. Sensors Actuators B Chem 258:1051–1059CrossRefGoogle Scholar
  50. Ferreira ADBL, Nóvoa PRO, Marques AT (2016) Multifunctional material systems: a state-of-the-art review. Compos Struct 151:3–35CrossRefGoogle Scholar
  51. Fischer F (2018) Photoelectrode, photovoltaic and photosynthetic microbial fuel cells. Renew Sust Energ Rev 90:16–27CrossRefGoogle Scholar
  52. Fraas M, Glasenapp T, Schulz A, Bauer HJ (2019) Optimized inlet geometry of a laidback fan-shaped film cooling hole - experimental study of film cooling performance. Int J Heat Mass Transf 128:980–990CrossRefGoogle Scholar
  53. Fukuzumi S (2016) Artificial photosynthesis for production of hydrogen peroxide and its fuel cells. Biochimica et Biophysica Acta (BBA) – Bioenergetics 1857(5):604–611CrossRefGoogle Scholar
  54. Gaona-Reyes JL, Bermudez D (2017) The theory of optical black hole lasers. Ann Phys 380:41–58CrossRefGoogle Scholar
  55. Gehlot R, Tripathi B (2016) Thermal analysis of holes created on ceramic coating for diesel engine piston. Case Stud Thermal Eng 8:291–299CrossRefGoogle Scholar
  56. Gomis-Berenguer A, Velasco LF, Velo-Gala I, Ania CO (2017) Photochemistry of nanoporous carbons: perspectives in energy conversion and environmental remediation. J Colloid Interface Sci 490:879–901CrossRefGoogle Scholar
  57. Green MJ, Behabtu N, Pasquali M, Adams WW (2009) Nanotubes as polymers. Polymer 50:4979–4997CrossRefGoogle Scholar
  58. Guiderdoni C, Pavlenko E, Turq V, Weibel A, Puech P, Estournès C, Peigney A, Bacsa W, Laurent C (2013) The preparation of carbon nanotube (CNT)/copper composites and the effect of the number of CNT walls on their hardness, friction and wear properties. Carbon 58:185–197CrossRefGoogle Scholar
  59. Guler MT, Beyazkilic P, Elbuken C (2017) A versatile plug microvalve for microfluidic applications. Sensors Actuators A Phys 265:224–230CrossRefGoogle Scholar
  60. Guo W, Tam HY (2011) Effects of extended punching on wear of the WC/Co micropunch and the punched microholes. Int J Adv Manuf Technol 59:955–960.  https://doi.org/10.1007/s00170-011-3567-0CrossRefGoogle Scholar
  61. Gutierrez F, Rubianes MD, Rivas GA (2012) Dispersion of multi-wall carbon nanotubes in glucose oxidase: characterization and analytical applications for glucose biosensing. Sensors Actuators B Chem 012(161):191–197Google Scholar
  62. Haghighi F, Talebpour Z, Nezhad AS (2018) Towards fully integrated liquid chromatography on a chip: evolution and evaluation. TrAC Trends Anal Chem 105:302–337CrossRefGoogle Scholar
  63. Hakimi O, Ventura Y, Goldman J, Vago R, Aghion E (2016) Porous biodegradable EW62 medical implants resist tumor cell growth. Mater Sci Eng C 61:516–525CrossRefGoogle Scholar
  64. Hashemi SMH, Neuenschwander M, Hadikhani P, Modestino MA, Psaltis D (2017) Membrane-less micro fuel cell based on two-phase flow. J Power Sources 348:212–218CrossRefGoogle Scholar
  65. Hatsuzawa T, Ito D, Nisisako T, Yanagida Y (2017) Micro-rotary ratchets driven by migratory phytoplankton with phototactic stimulus. Precis Eng 48:107–113CrossRefGoogle Scholar
  66. Hayes SA, Nix AC, Nestor CM, Billups DT, Haught SM (2017) Experimental investigation of the influence of freestream turbulence on an anti-vortex film cooling hole. Exp Thermal Fluid Sci 81:314–326CrossRefGoogle Scholar
  67. Hilber W, Jakoby B (2015) Ethanol fermentation as the basis for autonomous, long-term and high-pressure fluid transport in microfluidics. Proc Eng 120:100–105CrossRefGoogle Scholar
  68. Ho KC, Teow YH, Mohammad AW, Ang WL, Lee PH (2018) Development of graphene oxide (GO)/multi-walled carbon nanotubes (MWCNTs) nanocomposite conductive membranes for electrically enhanced fouling mitigation. J Membr Sci 552:189–201CrossRefGoogle Scholar
  69. Hoysall DC, Garimella S (2018) Investigation of a serpentine micro-pin fin heat and mass exchanger for absorption systems. Int J Refrig 93:108–121CrossRefGoogle Scholar
  70. Hsu MC, Alfadhel A, Forouzandeh F, Borkholder DA (2018) Biocompatible magnetic nanocomposite microcapsules as microfluidic one-way diffusion blocking valves with ultra-low opening pressure. Mater Des 150:86–93CrossRefPubMedPubMedCentralGoogle Scholar
  71. Hvizdoš P, Puchý V, Duszová A, Dusza J, Balázsi C (2012) Tribological and electrical properties of ceramic matrix composites with carbon nanotubes. Ceram Int 38:5669–5676CrossRefGoogle Scholar
  72. Iijima S (1991) Helical microtubules of graphitic carbon. Nature 354:56–58CrossRefGoogle Scholar
  73. Iijima S (1993) Single-shell carbon nanotubes of 1-nm diameter. Nature 363:603–605CrossRefGoogle Scholar
  74. Jäckel N, Weingarth D, Schreiber A, Krüner B, Zeiger M, Tolosa A, Aslan M, Presser V (2016) Performance evaluation of conductive additives for activated carbon supercapacitors in organic electrolyte. Electrochim Acta 191:284–298CrossRefGoogle Scholar
  75. Janssen PJM, Hoefnagels JPM, de Keijser TH, Geers MGD (2008) Processing induced size effects in plastic yielding upon miniaturization. J Mech Phys Solids 56:2687–2706CrossRefGoogle Scholar
  76. Johnstone RW, Parameswaran M (2004) An introduction to surface-micromachining. Kluwer Academic, DordrechtCrossRefGoogle Scholar
  77. Kant R, Singh D, Bhattacharya S (2017) Digitally controlled portable micropump for transport of live micro-organisms. Sensors Actuators A Phys 265:138–151CrossRefGoogle Scholar
  78. Kenig EY, Su YH, Lautenschleger A, Chasanis P, Grünewald M (2013) Micro-separation of fluid systems: a state-of-the-art review. Sep Purif Technol 120:245–264CrossRefGoogle Scholar
  79. Kim JH, Kim KY (2018) Film-cooling performance of converged-inlet hole shapes. Int J Therm Sci 124:196–211CrossRefGoogle Scholar
  80. Kim T, Park S (2018) Modeling flash boiling breakup phenomena of fuel spray from multi-hole type direct-injection spark-ignition injector for various fuel components. Energy Convers Manag 160:165–175CrossRefGoogle Scholar
  81. Knobloch H, Kaminorz Y (2004) MicroNano integration. Springer-Verlag, Berlin/HeidlbergCrossRefGoogle Scholar
  82. Korkmaz E, Gozen BA, Bediz B, Ozdoganlar OB (2017) Accurate measurement of micromachining forces through dynamic compensation of dynamometers. Precis Eng 49:365–376CrossRefGoogle Scholar
  83. Kowsari K, Amini MH, Papini M, Spelt JK (2016) The effects of fluid vapor pressure and viscosity on the shapes of abrasive slurry-jet micro-machined holes and channels. Int J Mach Tools Manuf 110:80–91CrossRefGoogle Scholar
  84. Krewinkel R (2013) A review of gas turbine effusion cooling studies. Int J Heat Mass Transf 66:706–722CrossRefGoogle Scholar
  85. Krishnamoorthi M, Malayalamurthi R (2018) Engine characteristics analysis of chaulmoogra oil blends and corrosion analysis of injector nozzle using scanning electron microscopy/energy dispersive spectroscopy. Energy 165,. Part B:1292–1319CrossRefGoogle Scholar
  86. Kudźma Z, Stosiak M (2015) Studies of flow and cavitation in hydraulic lift valve. Arch Civil Mech Eng 15(4):951–961CrossRefGoogle Scholar
  87. Kumar R, Kumar A, Singh I (2018) Electric discharge drilling of micro holes in CFRP laminates. J Mater Process Technol 259:150–158CrossRefGoogle Scholar
  88. Kuriakose S, Mangalan AV, Namboothiri B, Ray A (2016) Micro machining process selection: an integrated theory. Proc Technol 25:862–868CrossRefGoogle Scholar
  89. Lee S, Hwang W, Yee KJ (2018) Robust design optimization of a turbine blade film cooling hole affected by roughness and blockage. Int J Therm Sci 133:216–229CrossRefGoogle Scholar
  90. Li PC, Hu CC, You TH, Chen PY (2017) Development and characterization of bi-functional air electrodes for rechargeable zinc-air batteries: effects of carbons. Carbon 111:813–821CrossRefGoogle Scholar
  91. Lisowski E, Filo G (2016) CFD analysis of the characteristics of a proportional flow control valve with an innovative opening shape. Energy Convers Manag 123:15–28CrossRefGoogle Scholar
  92. Liu YH, Chang TH, Wang CC (2016) Heat transfer enhancement of an impinging synthetic air jet using diffusion-shaped orifice. Appl Therm Eng 94:178–185CrossRefGoogle Scholar
  93. Luttge R (2016) Chapter 2. Basic technologies for microsystems. In: Nano- and microfabrication for industrial and biomedical applications, 2nd edn. pp 11–54Google Scholar
  94. Luzardo FHM, Velasco FG, Correia IKS, Silva PMS, Salay LC (2017) Removal of lead ions from water using a resin of mimosa tannin and carbon nanotubes. Environ Technol Innovat 7:219–228CrossRefGoogle Scholar
  95. Madhavi JB, Hiremath SS (2016) Investigation on machining of holes and channels on borosilicate and sodalime glass using μ-ECDM setup. Proc Technol 25:1257–1264CrossRefGoogle Scholar
  96. Makaryants GM (2017) Fatigue failure mechanisms of a pressure relief valve. J Loss Prev Process Ind 48:1–13CrossRefGoogle Scholar
  97. Malama B, Kuhlman KL, Brauchler R, Bayer P (2016) Modeling cross-hole slug tests in an unconfined aquifer. J Hydrol 540:784–796CrossRefGoogle Scholar
  98. Mamalis AG (2005) Advanced manufacturing engineering. J Mater Process Technol 161:1–9CrossRefGoogle Scholar
  99. Mark JJ (2006) Microfabrication and nanomanufacturing. CRC/Taylor & Francis, Boca RatonGoogle Scholar
  100. Martinez S, Michaux G, Salagnac P, Bouvier JL (2017a) Micro-combined heat and power systems (micro-CHP) based on renewable energy sources. Energy Convers Manag 154:262–285CrossRefGoogle Scholar
  101. Martinez S, Michaux G, Salagnac P, Bouvier JL (2017b) Micro-combined heat and power systems (micro-CHP) based on renewable energy sources. Energy Convers Manag 154:262–285CrossRefGoogle Scholar
  102. Massarwi F, Machchhar J, Antolin P, Elber G (2018) Hierarchical, random and bifurcation tiling with heterogeneity in micro-structures construction via functional composition. Comput Aided Des 102:148–159CrossRefGoogle Scholar
  103. Mazaheri K, Zeinalpour M, Bokaei HR (2016) Turbine blade cooling passages optimization using reduced conjugate heat transfer methodology. Appl Therm Eng 103:1228–1236CrossRefGoogle Scholar
  104. McInturff P, Suzuki M, Ligrani P, Nakamata C, Lee DH (2018) Effects of hole shape on impingement jet array heat transfer with small-scale, target surface triangle roughness. Int J Heat Mass Transf 127(Part A):585–597CrossRefGoogle Scholar
  105. Mohamed GH (2006) The MEMS handbook. CRC/Taylor & Francis, Boca RatonGoogle Scholar
  106. Mohan B, Du JG, Sim J, Roberts WL (2018) Hydraulic characterization of high-pressure gasoline multi-hole injector. Flow Meas Instrum 64:133–141CrossRefGoogle Scholar
  107. Monošík R, Angnes L (2015) Utilisation of micro- and nanoscaled materials in microfluidic analytical devices. Microchem J 119:159–168CrossRefGoogle Scholar
  108. Moreno M, Arribas AS, Bermejo E, Zapardiel A, Chicharro M (2017) Carbon nanotubes as analytical tools in capillary electromigration methods. Appl Mater Today 9:456–481CrossRefGoogle Scholar
  109. Muniak DP (2015) A proposal for a new methodology to determine inner authority of the control valve in the heating system. Appl Energy 155:421–433CrossRefGoogle Scholar
  110. Munk DJ, Kipouros T, Vio GA, Steven GP, Parks GT (2017) Topology optimisation of micro fluidic mixers considering fluid-structure interactions with a coupled Lattice Boltzmann algorithm. J Comput Phys 349:11–32CrossRefGoogle Scholar
  111. Nguyen TD (2013) Portraits of colloidal hybrid nanostructures: controlled synthesis and potential applications. Colloids Surf B: Biointerfaces 103:326–344CrossRefGoogle Scholar
  112. Nyström L, Malmsten M (2016) Surface-bound microgels-from physicochemical properties to biomedical applications. Adv Colloid Interf Sci 238:88–104CrossRefGoogle Scholar
  113. Okhotnikov I, Noroozi S, Sewell P, Godfrey P (2017) Evaluation of steady flow torques and pressure losses in a rotary flow control valve by means of computational fluid dynamics. Int J Heat Fluid Flow 64:89–102CrossRefGoogle Scholar
  114. Oliver G, Henning K, Pieter T (2004) Microsystem engineering of lab-on-a-chip devices. Angew Chem 43(34):4382–4390CrossRefGoogle Scholar
  115. Pakarzadeh H, Rezaei SM, Namroodi L (2019) Hollow-core photonic crystal fibers for efficient terahertz transmission. Opt Commun 433:81–88CrossRefGoogle Scholar
  116. Palecki S, Gorelkov S, Wartmann J, Heinzel A (2017) Frost induced damages within porous materials - from concrete technology to fuel cells technique. J Power Sources 372:204–211CrossRefGoogle Scholar
  117. Paramo E, Palmero S, Heras A, Colina A (2018) Carbon nanostructured films modified by metal nanoparticles supported on filtering membranes for electroanalysis. Talanta 178:736–742CrossRefGoogle Scholar
  118. Park S, Jung EY, Kim SH, Sohn HS, Cho HH (2016) Enhancement of film cooling effectiveness using backward injection holes. Int J Therm Sci 110:314–324CrossRefGoogle Scholar
  119. Pina VG, Amigó V, Muñoz AI (2016) Microstructural, electrochemical and tribo-electrochemical characterisation of titanium-copper biomedical alloys. Corros Sci 109:115–125CrossRefGoogle Scholar
  120. Pöllänen M, Pirinen S, Suvanto M, Pakkanen TT (2011) Influence of carbon nanotube–polymeric compatibilizer masterbatches on morphological, thermal, mechanical, and tribological properties of polyethylene. Compos Sci Technol 71:1353–1360CrossRefGoogle Scholar
  121. Pradeep A, Raj SV, Stanley J, Nair BG, Babu TGS (2018) Automated and programmable electromagnetically actuated valves for microfluidic applications. Sensors Actuators A Phys 283:79–86CrossRefGoogle Scholar
  122. Pratyusha T, Sivakumar G, Gupta D, Yella A (2017) Unique hole transport layer of PCDTBT doped with PCPDTBT for perovskite solar cells. Mater Today Proc 4(7, Part 1):6820–6826CrossRefGoogle Scholar
  123. Price C, Hamzehloo A, Aleiferis P, Richardson D (2018) Numerical modelling of fuel spray formation and collapse from multi-hole injectors under flash-boiling conditions. Fuel 221:518–541CrossRefGoogle Scholar
  124. Puch F, Hopmann C (2014) Morphology and tensile properties of unreinforced and short carbon fibre reinforced nylon 6/multiwalled carbon nanotube-composites. Polymer 55(13):3015–3025CrossRefGoogle Scholar
  125. Ramesh S, Ramirez DG, Ekkad SV, Alvin MA (2016) Analysis of film cooling performance of advanced tripod hole geometries with and without manufacturing features. Int J Heat Mass Transf 94:9–19CrossRefGoogle Scholar
  126. Ramos A, Mesnard M (2016) A new condyle implant design concept for an alloplastic temporomandibular joint in bone resorption cases. J Cranio-Maxillofac Surg 44(10):1670–1677CrossRefGoogle Scholar
  127. Ranjan R, Chou SK, Riaz F, Karthikeyan K (2017) Cold gas micro propulsion development for satellite application. Energy Procedia 143:754–761CrossRefGoogle Scholar
  128. Ravi D, Yohannes S, Koteswararao B, Satish K, Kishorebabu KS (2018) Structural analysis of down the hole button bit with different materials. Mater Today Proc 5(2), Part 1):4711–4719CrossRefGoogle Scholar
  129. Rittel D, Dorogoy A, Shemtov-Yona K (2017) Modelling dental implant extraction by pullout and torque procedures. J Mech Behav Biomed Mater 71:416–427CrossRefGoogle Scholar
  130. Rogers CI, Oxborrow JB, Anderson RR, Tsai LF, Nordin GP, Woolley AT (2014) Microfluidic valves made from polymerized polyethylene glycol diacrylate. Sensors Actuators B Chem 191:438–444CrossRefGoogle Scholar
  131. Rosace G, Trovato V, Colleoni C, Caldara M, Re V, Brucale M, Piperopoulos E, Mastronardo E, Milone C, De Luca G, Plutino MR (2017) Structural and morphological characterizations of MWCNTs hybrid coating onto cotton fabric as potential humidity and temperature wearable sensor. Sensors Actuators B Chem 252:428–439CrossRefGoogle Scholar
  132. Rupp F, Liang L, Geis-Gerstorfer J, Scheideler L, Hüttig F (2018) Surface characteristics of dental implants: a review. Dent Mater 34(1):40–57CrossRefGoogle Scholar
  133. Saadati SA, Roohi E (2015) Detailed investigation of flow and thermal field in micro/nano nozzles using Simplified Bernoulli Trial (SBT) collision scheme in DSMC. Aerosp Sci Technol 46:236–255CrossRefGoogle Scholar
  134. Samih S, Latifi M, Farag S, Leclerc P, Chaouki J (2018) From complex feedstocks to new processes: the role of the newly developed micro-reactors. Chem Eng Process Process Intensif 131:92–105CrossRefGoogle Scholar
  135. Sarafraz MM, Hormozi F, Peyghambarzadeh SM (2016) Pool boiling heat transfer to aqueous alumina nano-fluids on the plain and concentric circular micro-structured (CCM) surfaces. Exp Thermal Fluid Sci 72:125–139CrossRefGoogle Scholar
  136. Satta F, Tanda G (2015) Effect of discrete-hole arrangement on film-cooling effectiveness for the endwall of a turbine blade cascade. Appl Therm Eng 91:507–514CrossRefGoogle Scholar
  137. Saxena KK, Qian J, Reynaerts D (2018) A review on process capabilities of electrochemical micromachining and its hybrid variants. Int J Mach Tools Manuf 127:28–56CrossRefGoogle Scholar
  138. Sayindla S, Lund B, Ytrehus JD, Saasen A (2017) Hole-cleaning performance comparison of oil-based and water-based drilling fluids. J Pet Sci Eng 159:49–57CrossRefGoogle Scholar
  139. Schütze C, Dietrich P, Sauer U (2013) Diagnostic monitoring to identify preferential near-surface structures for CO2 degassing into the atmosphere: tools for investigations at different spatial scales validated at a natural analogue site. Int J Greenhouse Gas Control 18:285–295CrossRefGoogle Scholar
  140. Sciubba E (2015) Air-cooled gas turbine cycles – part 1: an analytical method for the preliminary assessment of blade cooling flow rates. Energy 83:104–114CrossRefGoogle Scholar
  141. Sehrawat P, Julien C, Islam SS (2016) Carbon nanotubes in Li-ion batteries: a review. Mater Sci Eng B 213:12–40CrossRefGoogle Scholar
  142. Sharma DS, Patel NP, Trivedi RR (2014) Optimum design of laminates containing an elliptical hole. Int J Mech Sci 85:76–87CrossRefGoogle Scholar
  143. Shetzline JA, Bukola S, Creager SE (2017) A convenient miniature test platform for polyelectrolyte membrane fuel-cell research. J Electroanal Chem 797:8–15CrossRefGoogle Scholar
  144. Shin HS, Kwon OJ, Oh BS (2018) Correlation between performance of polymer electrolyte membrane fuel cell and degradation of the carbon support in the membrane electrode assembly using image processing method. Int J Hydrog Energy 43(45):20921–20930CrossRefGoogle Scholar
  145. Silaskar SM, Shinde VB (2018) Weight optimization of valve for cost effectiveness: using value analysis. Proc Manuf 20:329–337Google Scholar
  146. Singh VK, Tharakan TJ (2015) Numerical simulations for multi-hole orifice flow meter. Flow Meas Instrum 45:375–383CrossRefGoogle Scholar
  147. Singh A, Manikandan NA, Sankar MR, Pakshirajan K, Roy L (2018) Experimental investigations and surface morphology of bio-micromachining on copper. Mater Today Proc 5(2, Part 1):4225–4234CrossRefGoogle Scholar
  148. Takahashi H, Nakai A, Shimoyama I (2018) Waterproof airflow sensor for seabird bio-logging using a highly sensitive differential pressure sensor and nano-hole array. Sensors Actuators A Phys 281:243–249CrossRefGoogle Scholar
  149. Taniguchi N, Jinno T, Takada R, Koga D, Ando T, Okawa A, Haro H (2018) Do screws and screw holes affect osteolysis in cementless cups using highly crosslinked polyethylene? A 7 to 10-year follow-up case-control study. Orthop Traumatol Surg Res 104(3):307–315CrossRefGoogle Scholar
  150. Tanimu A, Jaenicke S, Alhooshani K (2017) Heterogeneous catalysis in continuous flow microreactors: a review of methods and applications. Chem Eng J 327:792–821CrossRefGoogle Scholar
  151. Tesař V (2017) Fluid mechanics of needle valves with rounded components part I: configurations and models. Sensors Actuators A Phys 254:101–108CrossRefGoogle Scholar
  152. Tharmavaram M, Pandey G, Rawtani D (2018) Surface modified halloysite nanotubes: a flexible interface for biological, environmental and catalytic applications. Adv Colloid Interf Sci 261:82–101CrossRefGoogle Scholar
  153. Theodorakakos A, Strotos G, Mitroglou N, Atkin C, Gavaises M (2014a) Friction-induced heating in nozzle hole micro-channels under extreme fuel pressurization. Fuel 123:143–150CrossRefGoogle Scholar
  154. Theodorakakos A, Strotos G, Mitroglou N, Atkin C, Gavaises M (2014b) Friction-induced heating in nozzle hole micro-channels under extreme fuel pressurization. Fuel 123:143–150CrossRefGoogle Scholar
  155. Tiusanen J, Vlasveld D, Vuorinen J (2012) Review on the effects of injection moulding parameters on the electrical resistivity of carbon nanotube filled polymer parts. Compos Sci Technol 72:1741–1752CrossRefGoogle Scholar
  156. Tofighy MA, Mohammadi T (2011) Adsorption of divalent heavy metal ions from water using carbon nanotube sheets. J Hazard Mater 185:140–147CrossRefGoogle Scholar
  157. Torelli R, Som S, Pei YJ, Zhang Y, Traver M (2017) Influence of fuel properties on internal nozzle flow development in a multi-hole diesel injector. Fuel 204:171–184CrossRefGoogle Scholar
  158. Torre FL, Kenjereš S, Moerel JL, Kleijn CR (2011) Hybrid simulations of rarefied supersonic gas flows in micro-nozzles. Comput Fluids 49(1):312–322CrossRefGoogle Scholar
  159. Trotta G, Volpe A, Ancona A, Fassi I (2018) Flexible micro manufacturing platform for the fabrication of PMMA microfluidic devices. J Manuf Process 35:107–117CrossRefGoogle Scholar
  160. Tsur EE, Shamir A (2018) Computer-aided design of resistance micro-fluidic circuits for 3D printing. Comput Aided Des 98:12–23CrossRefGoogle Scholar
  161. Tu J, Paleocrassas AG, Reeves N, Rajule N (2014) Experimental characterization of a micro-hole drilling process with short micro-second pulses by a CW single-mode fiber laser. Opt Lasers Eng 55:275–283CrossRefGoogle Scholar
  162. Tverskoy MM, Andrianov VN, Sokolov AV (2017) Creating new generation of actuators for shut-off and control ball valves with double-gate. Proc Eng 206:1303–1308CrossRefGoogle Scholar
  163. Uhlmann E, Mullany B, Biermann D, Rajurkar KP, Hausotte T, Brinksmeier E (2016) Process chains for high-precision components with micro-scale features. CIRP Ann Manuf Technol 65:549–572CrossRefGoogle Scholar
  164. Upadhyayula VKK, Gadhamshetty V (2010) Appreciating the role of carbon nanotube composites in preventing biofouling and promoting biofilms on material surfaces in environmental engineering: a review. Biotechnol Adv 28:802–816CrossRefGoogle Scholar
  165. Virkar AV (2012) Transport through mixed proton, oxygen ion and electron/hole conductors: analysis of fuel cells and electrolyzer cells using Onsager equations. Int J Hydrog Energy 37(17):12609–12628CrossRefGoogle Scholar
  166. Willich C, White AJ (2017) Heat transfer losses in reciprocating compressors with valve actuation for energy storage applications. J Energy Storage 14., Part(2):322–328CrossRefGoogle Scholar
  167. Yadav SP, Singh S (2016) Carbon nanotube dispersion in nematic liquid crystals: an overview. Prog Mater Sci 80:38–76CrossRefGoogle Scholar
  168. Zangl K, Danzl R, Helmli F, Prantl M (2018) Highly accurate optical μCMM for measurement of micro holes. Proc CIRP 75:397–402CrossRefGoogle Scholar
  169. Zhai P, Isaacs JA, Eckelman MJ (2016) Net energy benefits of carbon nanotube applications. Appl Energy 173:624–634CrossRefGoogle Scholar
  170. Zhan GD, Kuntz JD, Wan JL, Mukherjee AK (2003) Single-wall carbon nanotubes as attractive toughening agents in alumina-based nanocomposites. Nat Mater 2(1):38–42CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2020

Authors and Affiliations

  • Kelvii Wei Guo
    • 1
  1. 1.Department of Mechanical and Biomedical EngineeringCity University of Hong KongKowloonHong Kong

Personalised recommendations