Advertisement

Effects of Extrusion Conditions on Microstructure and Age-Hardening Behaviors of Al–Zn–Mg Alloy

  • Y. L. Wang
  • H. C. JiangEmail author
  • D. Zhang
  • L. J. Rong
Conference paper
Part of the Springer Proceedings in Physics book series (SPPHY, volume 217)

Abstract

Hot extrusions were performed to study the effects of extrusion conditions on microstructure, age-hardening behaviors and mechanical properties of Al–Zn–Mg alloy. The increasing of extrusion ratio from 10 to 35 effectively enhanced solid solubility of the as-extruded sheets. It accelerated the age-hardening response and significantly increased the number density of nanoscale matrix precipitates in peak-aged sheets. Higher extrusion ratio led to narrower extruded fibers in the sheets, while the extrusion temperature showed the opposite effect. The number of <111>//ED grains significantly decreased while that of <001>//ED grains increased a lot with increasing of extrusion ratio. Due to the differences in degree of deformation, grain size decreased monotonously from center to surface, thus contributing to the higher strength near the surface of peak-aged sheets than the center. The mechanical properties can be more homogeneous on cross section of the sheets by appropriately increasing extrusion ratio and temperature.

Keywords

Extrusion ratio Extrusion temperature Al–Zn–Mg alloy Age-hardening behaviors Microstructure 

Notes

Acknowledgements

The authors acknowledge the financial supports by National Key R&D Program of China (No. 2016YFB1200504) and Strategic Priority Program of the Chinese Academy of Sciences (No. XDB22000000).

References

  1. 1.
    S. Kaneko et al., Effect of the extrusion conditions on microstructure evolution of the extruded Al–Mg–Si–Cu alloy rods. Mater. Sci. Eng. A 500(1–2), 8–15 (2009)CrossRefGoogle Scholar
  2. 2.
    J.C. Williams, E.A. Starke Jr., Progress in structural materials for aerospace systems 1. Acta Mater. 51(19), 5775–5799 (2003)CrossRefGoogle Scholar
  3. 3.
    J.G. Tang et al., Influence of quench-induced precipitation on aging behavior of Al-Zn-Mg-Cu alloy. T. Nonferrous Met. Soc. 22(6), 1255–1263 (2012)CrossRefGoogle Scholar
  4. 4.
    Y.L. Wang et al., Two-stage double peaks ageing and its effect on stress corrosion cracking susceptibility of Al-Zn-Mg alloy. J. Mater. Sci. Technol. 34(7), 1250–1257 (2018)CrossRefGoogle Scholar
  5. 5.
    J. Zhou, J. Duszczyk, Effect of extrusion conditions on mechanical properties of Al-20Si-3Cu-1Mg alloy prepared from rapidly solidified powder. J. Mater. Sci. 26(14), 3739–3747 (1991)CrossRefGoogle Scholar
  6. 6.
    S. Kumar et al., Effect of extrusion parameters on the microstructure and properties of an Al-Li-Mg-Zr alloy. J. Mater. Sci. 29(4), 1067–1074 (1994)CrossRefGoogle Scholar
  7. 7.
    S. Karabay et al., Investigation extrusion ratio effect on mechanical behaviour of extruded alloy AA-6063. J. Mater. Process. Technol. 135(1), 101–108 (2003)CrossRefGoogle Scholar
  8. 8.
    C.D. He et al., Precipitation process and effect of precipitated phases of 7050 aluminum alloy two-stage double peak aging. Mater. Mech. Eng. 35(6), 38–41 (2011). (in Chinese)Google Scholar
  9. 9.
    X.Y. Sun et al., Correlations between stress corrosion cracking susceptibility and grain boundary microstructures for an Al-Zn-Mg alloy. Corros. Sci. 77, 103–112 (2013)CrossRefGoogle Scholar
  10. 10.
    Y.L. Wang et al., Variation of nanoparticle fraction and compositions in two-stage double peaks aging precipitation of Al−Zn−Mg alloy. Nanoscale Res. Lett. 13(1), 131 (2018)CrossRefGoogle Scholar
  11. 11.
    H. Adachi et al., Effect of hot-extrusion conditions on mechanical properties and microstructure of P/M Al-Zn-Mg-Cu alloys containing Zr. Mater. Sci. Forum, 1479–1484 (2006)CrossRefGoogle Scholar
  12. 12.
    A. Deschamps et al., Influence of predeformation on ageing in an Al–Zn–Mg alloy—I. Microstructure evolution and mechanical properties. Acta Mater. 47(1), 281–292 (1998)CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2019

Authors and Affiliations

  • Y. L. Wang
    • 1
    • 2
  • H. C. Jiang
    • 1
    Email author
  • D. Zhang
    • 1
    • 2
  • L. J. Rong
    • 1
  1. 1.CAS Key Laboratory of Nuclear Materials and Safety AssessmentInstitute of Metal Research, Chinese Academy of ScienceShenyangChina
  2. 2.School of Materials Science and EngineeringUniversity of Science and Technology of ChinaHefeiChina

Personalised recommendations