Advertisement

Micro-EDM Drilling

  • S. N. B. Oliaei
  • Muhammad P. Jahan
  • Asma PerveenEmail author
Chapter
Part of the Materials Forming, Machining and Tribology book series (MFMT)

Abstract

Micro-EDM drilling becomes an important fabrication process for several different industrial applications. Micro-EDM drilling provides comparative advantages over conventional mechanical micro-drilling process owing to its capability of machining difficult-to-cut materials. This chapter provides a concise overview of micro-EDM drilling process. It presents working principle of the micro-EDM drilling as well as both operating and performance parameters along with some important applications. This chapter also covers micro-EDM drilling for difficult-to-cut materials such as steel alloys, Ti alloys and Ni alloys.

Keywords

Micro-EDM Holes Nozzle High aspect ratio Taper Debris 

References

  1. 1.
    Yamane Y, Sekiya K (2004) An evaluation of difficulty in machining difficult-to-cut materials by using difficult-to-cut rating. J JSPE 70(3):407–411Google Scholar
  2. 2.
    Prakash V, Kumar P, Hussain M, Das AK, Chattopadhyaya S (2017) Micro-electrical discharge machining of difficult-to-machine materials: a review. Proc Inst Mech Eng, Part B: J Eng Manuf.  https://doi.org/10.1177/0954405417718591
  3. 3.
    Ho KH, Newman ST (2003) State of the art electrical discharge machining (EDM). Int J Mach Tools Manuf 43(13):1287–1300CrossRefGoogle Scholar
  4. 4.
    Pham DT, Dimov SS, Bigot S, Ivanov A, Popov K (2004) Micro-EDM—recent developments and research issues. J Mater Process Technol 149(1–3):50–57CrossRefGoogle Scholar
  5. 5.
    Masuzawa T (2000) State of the art of micromachining. CIRP Ann Manuf Technol 49(2):473–488CrossRefGoogle Scholar
  6. 6.
    Meek JM, Craggs JD (1978) Electrical breakdown of gases. Wiley, New YorkzbMATHGoogle Scholar
  7. 7.
    Lee TH (1959) T-F theory of electron emission in high-current arcs. J Appl Phys 30(2):166–171CrossRefGoogle Scholar
  8. 8.
    Kunieda M, Lauwers B, Rajurkar MP, Schumacher BM (2005) Advancing EDM through fundamental insight into the process. CIRP Ann Manuf Technol 54(2):64–87CrossRefGoogle Scholar
  9. 9.
    Hockenberry TO, Williams EM (1967) Dynamic evolution of events accompanying the low-voltage discharges employed in EDM. IEEE Trans Ind Gen Appl 4:302–309CrossRefGoogle Scholar
  10. 10.
    Kumar K, Rawal SK, Singh VP, Bala A (2018) Experimental study on diametric expansion and taper rate in EDM drilling for high aspect ratio micro holes in high strength materials. Mater Today: Proc 5(2, Part 2):7363–7372CrossRefGoogle Scholar
  11. 11.
    Qian J, Yang F, Wang J, Lauwers B, Reynaerts D (2015) Material removal mechanism in low-energy micro-EDM process. CIRP Ann 64(1):225–228CrossRefGoogle Scholar
  12. 12.
    Wong YS, Rahman M, Lim HS, Han H, Ravi N (2003) Investigation of micro-EDM material removal characteristics using single RC-pulse discharges. J Mater Process Technol 140(1–3):303–307CrossRefGoogle Scholar
  13. 13.
    Singh A, Ghosh A (1999) A thermo-electric model of material removal during electric discharge machining. Int J Mach Tools Manuf 39(4):669–682CrossRefGoogle Scholar
  14. 14.
    Muralikrishnan B, Stone J, Stoup J (2009) Diameter and form measurement of a micro-hole in a fuel injector nozzle with the NIST fiber probe. In: Proceedings of ASPE annual meeting, Monterey, CanadaGoogle Scholar
  15. 15.
    Masuzawa T, Fujino M, Kobayashi K, Suzuki T, Kinoshita N (1985) Wire electro-discharge grinding for micro-machining. CIRP Ann Manuf Technol 34(1):431–434CrossRefGoogle Scholar
  16. 16.
    Rowe W, Miyashita M, Koenig W (1989) Centreless grinding research and its application in advanced manufacturing technology. CIRP Ann Manuf Technol 38(2):617–625CrossRefGoogle Scholar
  17. 17.
    Her M-G, Weng F-T (2001) Micro-hole machining of copper using the electro-discharge machining process with a tungsten carbide electrode compared with a copper electrode. Int J Adv Manuf Technol 17(10):715–719CrossRefGoogle Scholar
  18. 18.
    Yan B, Huang FY, Chow HM, Tsai JY (1999) Micro-hole machining of carbide by electric discharge machining. J Mater Process Technol 87(1–3):139–145CrossRefGoogle Scholar
  19. 19.
    Yu Z, Rajurkar KP, Shen H (2002) High aspect ratio and complex shaped blind micro holes by micro EDM. CIRP Ann Manuf Technol 51(1):359–362CrossRefGoogle Scholar
  20. 20.
    Fu Y, Miyamoto T, Natsu W, Zhao W, Yu Z (2016) Study on influence of electrode material on hole drilling in micro-EDM. Procedia CIRP 42:516–520CrossRefGoogle Scholar
  21. 21.
    Reynaerts D, Heeren PH, Brussel HV (1997) Microstructuring of silicon by electro-discharge machining (EDM)—part I: theory. Sens Actuators A: Phys 60(1–3):212–218CrossRefGoogle Scholar
  22. 22.
    Ay M, Çaydaş U, Hasçalık A (2013) Optimization of micro-EDM drilling of Inconel 718 superalloy. Int J Adv Manuf Technol 66(5–8):1015–1023CrossRefGoogle Scholar
  23. 23.
    Yu ZY, Zhang Y, Li J, Luan J, Zhao F, Guo D (2009) High aspect ratio micro-hole drilling aided with ultrasonic vibration and planetary movement of electrode by micro-EDM. CIRP Ann 58(1):213–216CrossRefGoogle Scholar
  24. 24.
    Ferraris E, Castiglioni V, Ceyssens F, Annoni M, Lauwers B, Reynaerts D (2013) EDM drilling of ultra-high aspect ratio micro holes with insulated tools. CIRP Ann 62(1):191–194CrossRefGoogle Scholar
  25. 25.
    Masuzawa T, Tsukamoto J, Fujino M (1989) Drilling of deep microholes by EDM. CIRP Ann Manuf Technol 38(1):195–198CrossRefGoogle Scholar
  26. 26.
    Jahan MP, Wong YS, Rahman M (2010) A comparative experimental investigation of deep-hole micro-EDM drilling capability for cemented carbide (WC–Co) against austenitic stainless steel (SUS 304). Int J Adv Manuf Technol 46(9–12):1145–1160CrossRefGoogle Scholar
  27. 27.
    Diver C, Atkinson J, Helml HJ, Li L (2004) Micro-EDM drilling of tapered holes for industrial applications. J Mater Process Technol 149(1):296–303CrossRefGoogle Scholar
  28. 28.
    D’Urso G, Merla C (2014) Workpiece and electrode influence on micro-EDM drilling performance. Precis Eng 38(4):903–914CrossRefGoogle Scholar
  29. 29.
    D’Urso G, Maccarini G, Ravasio C (2014) Process performance of micro-EDM drilling of stainless steel. Int J Adv Manuf Technol 72(9):1287–1298CrossRefGoogle Scholar
  30. 30.
    Govindan P, Joshi SS (2010) Experimental characterization of material removal in dry electrical discharge drilling. Int J Mach Tools Manuf 50(5):431–443CrossRefGoogle Scholar
  31. 31.
    Chen ST (2007) A high-efficiency approach for fabricating mass micro holes by batch micro EDM. J Micromech Microeng 17(10):1961CrossRefGoogle Scholar
  32. 32.
    Chen ST (2008) Fabrication of high-density micro holes by upward batch micro EDM. J Micromech Microeng 18(8):085002CrossRefGoogle Scholar
  33. 33.
    Chern GL, Chuang Y (2006) Study on vibration-EDM and mass punching of micro-holes. J Mater Process Technol 180(1–3):151–160CrossRefGoogle Scholar
  34. 34.
    Liu HS, Yan BH, Huang FY, Qiu KH (2005) A study on the characterization of high nickel alloy micro-holes using micro-EDM and their applications. J Mater Process Technol 169(3):418–426CrossRefGoogle Scholar
  35. 35.
    Imran M, Mativenga PT, Gholinia A, Withers PJ (2015) Assessment of surface integrity of Ni superalloy after electrical-discharge, laser and mechanical micro-drilling processes. Int J Adv Manuf Technol 79(5–8):1303–1311CrossRefGoogle Scholar
  36. 36.
    Hung JC, Wu WC, Yan BH, Huang FY, Wu KL (2007) Fabrication of a micro-tool in micro-EDM combined with co-deposited Ni–SiC composites for micro-hole machining. J Micromech Microeng 17(4):763CrossRefGoogle Scholar
  37. 37.
    Perveen A, Jahan MP (2018) Application of Box Behnken design to model crater size generated during micro-EDM of NI-X alloy. Int J Mech Eng Rob Res 7(3):229–234Google Scholar
  38. 38.
    Perveen A, Jahan MP (2018) Comparative micro-EDM studies on Ni based X-alloy using coated and uncoated tools. Mater Sci Forum 911:13–19CrossRefGoogle Scholar
  39. 39.
    Bhosle RB, Sharma SB (2017) Multi-performance optimization of micro-EDM drilling process of Inconel 600 alloy. Mater Today: Proc 4(2, Part A):1988–1997Google Scholar
  40. 40.
    Meena VK, Azad MS (2012) Grey relational analysis of micro-EDM machining of Ti-6Al-4V alloy. Mater Manuf Process 27(9):973–977CrossRefGoogle Scholar
  41. 41.
    Li Y, Yu W, Xu J, Yu H (2016) A comparative investigation of micro-EDM drilling capability for Ti-6Al-4V alloy against austenitic stainless steel SUS 316. In: IEEE international conference on mechatronics and automation, Harbin, China, 7–10 Aug 2016Google Scholar
  42. 42.
    Plaza S, Sanchez JA, Perez E, Gil R, Izquierdo B, Ortega N, Pombo I (2014) Experimental study on micro EDM-drilling of Ti6Al4V using helical electrode. Precis Eng 38(4):821–827CrossRefGoogle Scholar
  43. 43.
    Kibria G, Sarkar BR, Pradhan BB, Bhattacharyya B (2010) Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti-6Al-4V alloy. Int J Adv Manuf Technol 48(5–8):557–570CrossRefGoogle Scholar
  44. 44.
    Jahan MP, Wong YS, Rahman M (2012) Experimental investigations into the influence of major operating parameters during micro-electro discharge drilling of cemented carbide. Mach Sci Technol 16(1):131–156CrossRefGoogle Scholar
  45. 45.
    Wansheng Z, Zhenlong W, Shichun D, Guanxin C, Hongyu W (2002) Ultrasonic and electric discharge machining to deep and small hole on titanium alloy. J Mater Process Technol 120(1):101–106CrossRefGoogle Scholar
  46. 46.
    Perveen A, Jahan MP, Zhumagulov S (2018) Statistical modelling and optimization of micro electro discharge machining of Ti Alloy. Mater Today: Proc 5(2):4803–4810CrossRefGoogle Scholar
  47. 47.
    Tiwary AP, Pradhan BB, Bhattacharyya B (2015) Study on the influence of micro-EDM process parameters during machining of Ti–6Al–4V superalloy. Int J Adv Manuf Technol 76(1):151–160CrossRefGoogle Scholar
  48. 48.
    Alavi F, Jahan MP (2017) Optimization of process parameters in micro-EDM of Ti-6Al-4V based on full factorial design. Int J Adv Manuf Technol 92(1–4):167–187CrossRefGoogle Scholar
  49. 49.
    Krishnaraj V (2016) Optimization of process parameters in micro-EDM of Ti-6Al-4V Alloy. J Manuf Sci Prod 16(1):41–49Google Scholar
  50. 50.
    Jahan MP, Rahman M, Wong YS (2011) A review on the conventional and micro-electrodischarge machining of tungsten carbide. Int J Mach Tools Manuf 51(12):837–858CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2019

Authors and Affiliations

  • S. N. B. Oliaei
    • 1
  • Muhammad P. Jahan
    • 2
  • Asma Perveen
    • 3
    Email author
  1. 1.Department of Mechanical EngineeringAtilim UniversityAnkaraTurkey
  2. 2.Department of Mechanical and Manufacturing EngineeringMiami UniversityOxfordUSA
  3. 3.Department of Mechanical EngineeringNazarbayev UniversityAstanaKazakhstan

Personalised recommendations