Plasma Nitriding of 2024 Al Alloy Deposited with Ti Film: Effects of N2–H2 Ratio on Microstructure Evolution and Mechanical Properties

Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

2024 Al alloys were firstly deposited with pure Ti film (~5.0 μm in thickness) using magnetron sputtering, then plasma nitrided for 8 h at 490 °C under N2–H2 gas mixtures with different N2 content (15, 40 and 50%). The Ti–N and Ti–Al diffusion reactions were activated simultaneously on the surface of Al alloy to obtain duplex coatings. The results showed that the duplex coatings were composed of nitride/aluminide layers (TiN0.3/Al3Ti/Al18Ti2Mg3 layers). With increasing the N2 content in the gas mixture, the peak ratio I(002)/I(100) of the outer TiN0.3 phase increased and the nitride particles grew larger. The surface hardness of coatings increased with the increasing N2–H2 ratio, reaching the maximum value of 630 HV under 50%N2 + 50%H2. The coatings obtained under gas mixture with high N content showed larger fluctuation at the initial stage during friction tests. All the obtained coatings showed the similar friction coefficient (~0.30) at the stable stage, much lower than the untreated Al alloy (~0.45). The sample nitrided under 50%N2 + 50%H2 exhibited the lowest wear rate, 60% lower than that of the uncoated one. The nitrided samples exhibited predominant abrasive wear and adhesive wear.

Keywords

2024 Al alloy Plasma nitriding Intermetallic coating Microstructure Wear resistance 

Notes

Acknowledgements

The authors gratefully acknowledge the National Natural Science Foundation of China (Grant No. U1537201), Natural Science Foundation of Tianjin (Grant No. 16JCQNJC03500), Natural Science Foundation of Hebei Province (Grant No. E2017202066) for the financial support of this research work.

References

  1. 1.
    H. Tang, Z. Cheng, J. Liu et al., Preparation of a high strength Al-Cu-Mg alloy by mechanical alloying and press-forming. Mater. Sci. Eng., A 550(31), 51–54 (2012)CrossRefGoogle Scholar
  2. 2.
    F. Khodabakhshi, A. Simchi, A.H. Kokabi, Surface modifications of an aluminum-magnesium alloy through reactive stir friction processing with titanium oxide nanoparticles for enhanced sliding wear resistance. Surf. Coat. Technol. 309, 114–123 (2017)CrossRefGoogle Scholar
  3. 3.
    M. Moradshahi, T. Tavakoli, S. Amiri et al., Plasma nitriding of Al alloys by DC glow discharge. Surf. Coat. Technol. 201(3), 567–574 (2006)CrossRefGoogle Scholar
  4. 4.
    F.F. Wei, W. Zhang, T. Zhang et al., Effect of variations of Al content on microstructure and corrosion resistance of PEO coatings on Mg Al alloys. J. Alloy. Compd. 690, 195–205 (2017)CrossRefGoogle Scholar
  5. 5.
    G. Hou, Y. An, X. Zhao et al., Improving interfacial, mechanical and tribological properties of alumina coatings on Al alloy by plasma arc heat-treatment of substrate. Appl. Sur. Sci. 411, 53–66 (2017)CrossRefGoogle Scholar
  6. 6.
    A. Fateme, H. Savaloni, Surface nanostructure modification of Al substrates by N+ ion implantation and their corrosion inhibition. T. Nonferr. Metal. Soc. 27(3), 701–710 (2017)CrossRefGoogle Scholar
  7. 7.
    H.C. Man, S. Zhang, T.M. Yue et al., Laser surface alloying of NiCrSiB on Al6061 aluminium alloy. Surf. Coat. Technol. 148(2), 136–142 (2001)CrossRefGoogle Scholar
  8. 8.
    V.H. Baggio-Scheid, G. de Vasconcelos, M.A.S. Oliveira, Duplex surface treatment of chromium pack diffusion and plasma nitriding of mild steel. Surf. Coat. Technol. 163–164, 313–317 (2003)CrossRefGoogle Scholar
  9. 9.
    F. Haftlang, A. Habibolahzadeh, M.H. Sohi, Comparative tribological studies of duplex surface treated AISI 1045 steels fabricated by combinations of plasma nitriding and aluminizing. Mater. Des. 60, 580–586 (2014)CrossRefGoogle Scholar
  10. 10.
    F. Haftlang, A. Habibolahzadeh, M.H. Sohi, Improving electrochemical properties of AISI 1045 steels by duplex surface treatment of plasma nitriding and aluminizing. Appl. Sur. Sci. 329, 240–247 (2015)CrossRefGoogle Scholar
  11. 11.
    Z.D. Liu, X.C. Zhang, F.Z. Xuan, Z.D. Wang, S.T. Tu, Process technological aspects of the production and properties of in situ combined plasma-nitrided and PVD hard-coated high alloy tool steels. Mater. Des. 37, 268–273 (2012)CrossRefGoogle Scholar
  12. 12.
    Z.D. Liu, X.C. Zhang, F.Z. Xuan et al., In situ synthesis of TiN/Ti3Al intermetallic matrix composite coatings on Ti6Al4V alloy. Mater. Des. 37, 268–273 (2012)CrossRefGoogle Scholar
  13. 13.
    N. Daemi, F. Mahboubi, H. Alimadadi, Effect of plasma nitriding on electrodeposited Ni-Al composite coating. Mater. Des. 32, 971–975 (2011)CrossRefGoogle Scholar
  14. 14.
    H.C. Man, S. Zhang, F.T. Cheng, Improving the wear resistance of AA 6061 by laser surface alloying with NiTi. Mater. Lett. 61, 4058–4061 (2007)CrossRefGoogle Scholar
  15. 15.
    A. Almeida, M. Anjos, R. Vilar et al., Laser alloying of aluminium alloys with chromium. Surf. Coat. Technol. 70(2–3), 221–229 (1995)CrossRefGoogle Scholar
  16. 16.
    F.Y. Zhang, M.F. Yan, Microstructure and mechanical properties of multiphase layer formed during depositing Ti film followed by plasma nitriding on 2024 aluminum alloy. Appl. Sur. Sci. 301, 410–417 (2014)CrossRefGoogle Scholar
  17. 17.
    F.Y. Zhang, M.F. Yan, Surf. Coat. Technol. 253, 268–276 (2014)CrossRefGoogle Scholar
  18. 18.
    M.F. Yan, R.L. Liu, Influence of process time on microstructure and properties of 17-4PH steel plasma nitrocarburized with rare earths addition at low temperature. Appl. Sur. Sci. 256, 6065–6071 (2010)CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2018

Authors and Affiliations

  • Fanyong Zhang
    • 1
    • 2
  • Mufu Yan
    • 3
  • Chen Lu
    • 3
  • Fuxing Yin
    • 1
    • 2
  1. 1.Research Institute for Energy Equipment Materials, Hebei University of TechnologyTianjinChina
  2. 2.Tianjin Key Laboratory of Materials Laminating Fabrication and Interface Control TechnologyHebei University of TechnologyTianjinChina
  3. 3.National Key Laboratory for Precision Hot Processing of Metals, School of Materials Science and EngineeringHarbin Institute of TechnologyHarbinChina

Personalised recommendations