Six-Port Based Load-Pull System
Chapter
Abstract
Chapter 4 provides a detailed treatment of six-port based setups for passive and active load/source-pull measurements, as well as a description of six-port based harmonic load/source-pull measurements. The load-pull measurements for on-wafer devices require special attention; therefore, an alternative approach for impedance and power flow calibration using a reflection based technique is described.
Keywords
Reflection Coefficient Output Port Input Port Reference Plane Device Under Test
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.
References
- 1.F.M. Ghannouchi, R. Larose, R.G. Bosisio, Y. Demers, A six-port network analyzer load-pull system for active load tuning. IEEE Trans. Instrum. Meas. 39(4), 628–631 (1990) CrossRefGoogle Scholar
- 2.R. Hajji, F.M. Ghannouchi, R.G. Bosisio, Large-signal microwave transistor modeling using multiharmonic load-pull measurements. Microw. Opt. Technol. Lett. 5(11), 580–585 (1992) ADSCrossRefGoogle Scholar
- 3.F.M. Ghannouchi, R.G. Bosisio, An automated millimeter-wave active load-pull measurement system based on six-port techniques. IEEE Trans. Instrum. Meas. 41(6), 957–962 (1992) CrossRefGoogle Scholar
- 4.F.M. Ghannouchi, F. Beauregard, A.B. Kouki, Large-signal stability and spectrum characterization of a medium power HBT using active load-pull techniques. IEEE Microw. Guided Wave Lett. 4(6), 191–193 (1994) CrossRefGoogle Scholar
- 5.F.M. Ghannouchi, G. Zhao, F. Beauregard, Simultaneous load-pull of intermodulation and output power under two tone excitation for accurate SSPA design. IEEE Trans. Microw. Theory Tech. 42(6), 943–950 (1994) CrossRefGoogle Scholar
- 6.F.M. Ghannouchi, F. Beauregard, R. Hajji, A. Brodeur, A de-embedding technique for reflection-based s-parameters measurements of HMICs and MMICs. Microw. Opt. Technol. Lett. 10(4), 218–222 (1995) CrossRefGoogle Scholar
- 7.R. Hajji, F. Beanregard, F.M. Ghannouchi, Multitone power and intermodulation load-pull characterization of microwave transistors suitable for linear Sspa’s design. IEEE Trans. Microw. Theory Tech. 45(7), 1093–1099 (1997) ADSCrossRefGoogle Scholar
- 8.D. Le, F.M. Ghannouchi, Multitone characterization and design of FET resistive mixers based on combined active source-pull/load-pull techniques. IEEE Trans. Instrum. Meas. 46(9), 1201–1208 (1998) Google Scholar
- 9.G. Berghoff, E. Bergeault, B. Huyart, L. Jallet, Automated characterization of HF power transistors by source-pull and multiharmonic load-pull measurements based on six-port techniques. IEEE Trans. Microw. Theory Tech. 46(12), 2068–2073 (1998) ADSCrossRefGoogle Scholar
- 10.S. Jia, New application of a single six-port reflectometer. Electron. Lett. 20, 920–922 (1984) CrossRefGoogle Scholar
- 11.J.D. Hunter, P.I. Slomo, S-parameter measurements with a single six-port. Electron. Lett. 21, 157–158 (1985) CrossRefGoogle Scholar
- 12.F.M. Ghannouchi, A. Mohammadi, The Six-Port Technique (Artech House, Norwood, 2009) Google Scholar
- 13.D. Le, F.M. Ghannouchi, Source-pull measurements using reverse six-port reflectometers with application to MESFET mixer design. IEEE Trans. Microw. Theory Tech. 42, 1589–1595 (1994) ADSCrossRefGoogle Scholar
- 14.T.E. Hodgetts, G.J. Griffin, A unified treatment of the six-port reflectometer calibration using a minimum of standards, Royal Signals and Radar Establishment Rep. No. B3003, 1983 Google Scholar
- 15.G.F. Engen, Calibrating the six-port reflectometer by means of sliding terminations. IEEE Trans. Microw. Theory Tech. 26, 951–957 (1978) ADSCrossRefGoogle Scholar
- 16.V. Teppati, A. Ferrero, U. Pisani, Recent advances in real-time load-pull systems. IEEE Trans. Instrum. Meas. 57, 2640–2646 (2008) CrossRefGoogle Scholar
- 17.D. Le, F.M. Ghannouchi, Noise measurements of microwave transistors using an uncalibrated mechanical stub tuner and a built-in reverse six-port reflectometer. IEEE Trans. Instrum. Meas. 44(4), 847–852 (1995) CrossRefGoogle Scholar
- 18.R.Q. Lane, Determination of device noise parameters. Proc. IEEE 57, 1461–1462 (1969) CrossRefGoogle Scholar
- 19.S.V. Bosch, L. Martens, Experimental verification of pattern selection for noise characterization. IEEE Trans. Microw. Theory Tech. 48(1), 156–158 (2000) ADSCrossRefGoogle Scholar
- 20.F.M. Ghannouchi, R. Larose, R.G. Bosisio, A new multiharmonic loading method for large-signal microwave transistor characterization. IEEE Trans. Microw. Theory Tech. 39, 986–992 (1991) ADSCrossRefGoogle Scholar
- 21.G. Gonzalez, Microwave Transistor Amplifiers Analysis and Design, 2nd edn. (Prentice-Hall, Englewood Cliffs, 1996) Google Scholar
- 22.F.M. Ghannouchi, R.G. Bosisio, Source-pull/load-pull oscillator measurements at microwave/mm wave frequencies. IEEE Trans. Instrum. Meas. 41, 32–35 (1992) CrossRefGoogle Scholar
- 23.T. Yakabe, M. Kinoshita, H. Yabe, Complete calibration of a six-port reflectometer with one sliding load and one short. IEEE Trans. Microw. Theory Tech. 42, 2035–2039 (1994) ADSCrossRefGoogle Scholar
- 24.K. Koyama, T. Kawasaki, J.E. Hanely, Measurement of AM-PM conversion coefficients. Telecommun. 12(6), 25–28 (1978) Google Scholar
- 25.J.F. Moss, AM-AM and AM-PM measurements using the PM null technique. IEEE Trans. Microw. Theory Tech. MTT-35(8), 780–782 (1987) ADSCrossRefGoogle Scholar
- 26.T. Parra, X-band low phase distortion MMIC power limiter. IEEE Trans. Microw. Theory Tech. 41(5), 876–879 (1993) ADSCrossRefGoogle Scholar
- 27.R.A. Soares, P. Gouzien, P. Legaud, G. Follot, A unified mathematical approach to two-port calibration techniques and some applications. IEEE Trans. Microw. Theory Tech. MTT-37, 1660–1674 (1989) ADSGoogle Scholar
Copyright information
© Springer Science+Business Media Dordrecht 2013