Secondary Bending for Mechanically Fastened Joints with Eccentricities

  • Andrzej Skorupa
  • Małgorzata Skorupa
Chapter
Part of the Solid Mechanics and Its Applications book series (SMIA, volume 189)

Abstract

In the case of joints eccentric with respect to the load path, like lap joints or single strap butt joints, out-of-plane deformations of the sheets referred to as secondary bending (SB) occur under nominally tensile loading. Maximum moments due to SB are induced at load path eccentricities, namely at the rivet rows. As said earlier, for a lap joint with more than two rivet rows, the maximum bending moment is always induced at the outer rows. The out-of-plane deformation of a lap joint with three rivet rows associated with SB is shown in Fig. 6.1a. The largest tensile stresses due to SB are produced along the faying surface at location A of sheet 1 and location B of sheet 2. Because outside the outer rivet rows either sheet carries the full applied tensile load, A and B are also locations of the maximum combined tensile stresses and, therefore, the most commonly observed fatigue crack initiation sites.

Keywords

Fatigue Life Sheet Thickness Beam Model Hole Expansion Faying Surface 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

References

  1. Änggård, J.: FE-analysis of riveted lap joint. TN 2000–15, The Aeronautical Research Institute of Sweden FFA (2000)Google Scholar
  2. Barrois, W.: Stress and displacements due to load transfer by fasteners in structural assemblies. Eng. Fract. Mech. 10, 115–176 (1978)CrossRefGoogle Scholar
  3. Brenner, L., Hübsch, B.: Lebensdauer-Untersuchungen an Nietverbindungen. Report EF 30-TB 8, Dornier, Friedrichshafen (1969)Google Scholar
  4. Chen, Ch-S., Wawrzynek, P.A., Ingraffea, A.R.: Crack growth simulation and residual strength predictions in airplane fuselages. NASA/CR-1999-209115. Langley Research Center, Hampton, VA (March 1999)Google Scholar
  5. Das, G.K., Miller, M., Sovar, T.: Durability assessment of fuselage single shear lap joint with pads. In: Rouchon, J. (ed.) Proceedings of 21th ICAF Symposium, Design for Durability in the Digital Age, Tolouse, France, 27–29 June 2001, pp. 567–595. Cépaduès Ėdition, Tolouse (2001)Google Scholar
  6. de Rijck, J.J.M.: Stress analysis of fatigue cracks in mechanically fastened joints. An analytical and experimental investigation. Ph.D. thesis, TU Delft, Delft (2005)Google Scholar
  7. Ekh, J., Schön, J.: Effect of secondary bending on strength prediction of composite, single shear lap joints. Compos. Sci. Technol. 65, 953–965 (2005)CrossRefGoogle Scholar
  8. Ekh, J., Schön, J., Melin, L.G.: Secondary bending in multi-fastener, composite-to-aluminium single shear lap joints. Compos.: Part B 36(2005), 195–208 (2005)CrossRefGoogle Scholar
  9. Fawaz, S.A.: Equivalent initial flaw size testing and analysis of transport aircraft skin splices. Fatigue Fract. Eng. Mater. Struct. 26, 279–290 (2003)CrossRefGoogle Scholar
  10. Fawaz, S.A., de Rijck, J.J.M.: A thin-sheet, combined tension and bending specimen. Exp. Mech. 39, 171–176 (1999)CrossRefGoogle Scholar
  11. Hartman, A.: The effect of secondary bending on the fatigue strength of (clad 2024-T3 and 7075-T6) aluminium alloy riveted joints. Report NLR TR 72007 U. NLR, Amsterdam (1972)Google Scholar
  12. Hartman, A., Schijve, J.: The effect of secondary bending on the fatigue strength of 2024-T3 Alclad riveted joints. Report NLR TR 69116U. NLR, Amsterdam (1969)Google Scholar
  13. Ireman, T.: Three-dimensional stress analysis of bolted single-lap composite joints. Compos. Struct. 43, 195–216 (1998)CrossRefGoogle Scholar
  14. Jarfall, L.: Shear loaded fastener installation. Int. J. Veh. Des. 7, 337–379 (1986)Google Scholar
  15. Müller, R.P.G.: An experimental and analytical investigation on the fatigue behaviour of fuselage riveted lap joints. The significance of the rivet squeeze force, and a comparison of 2024-T3 and Glare 3. Ph.D. thesis, TU Delft, Delft (1995)Google Scholar
  16. Newman, J.C., Jr., Harris, C.E., James, M.A., Shivakumar, K.N.: Fatigue life prediction of riveted lap splice joints using small crack theory. In: Cook, R., Poole, P. (eds.) Proceedings of 19th ICAF Symposium, Fatigue in New and Aging Aircraft, Edinburgh, Scotland, 18–20 June 1997, pp. 523–552. EMAS, Warley (1997)Google Scholar
  17. Phillips, E.P., Britt, V.O.: Measurements of a fuselage skin strains and displacements near a longitudinal lap joint in a pressurized aircraft. NASA Technical Memorandum TM 104163. Langley Research Center, Hampton, VA (Oct 1991)Google Scholar
  18. Rans, C.D.: The role of rivet installation on the fatigue performance of riveted lap joints. Ph.D. dissertation, Carleton University, Ottawa (2007)Google Scholar
  19. Schijve, J.: Some elementary calculations on secondary bending in simple lap joints. Report NLR TR 72036. NLR, Amsterdam (1972)Google Scholar
  20. Schijve, J.: Riveted lap joints with staggered thickness in the overlap of the joint. Calculation of secondary bending. Doc. B2-06-02. TU Delft, Faculty of Aerospace Engineering, Delft (2006)Google Scholar
  21. Schijve, J.: Fatigue of Structures and Materials, 2nd edn. Springer, Dordrecht/Heidelberg/London/New York (2009a) (with CD-Rom)CrossRefGoogle Scholar
  22. Schijve, J.: Fatigue damage in aircraft structures, not wanted, but tolerated? Int. J. Fatigue 31, 998–1011 (2009b)MATHCrossRefGoogle Scholar
  23. Schijve, J., Jacobs, F.A., Meulman, A.E.: Effect of an anti-corrosion penetrant on the fatigue life in flight-simulation tests on various riveted joints. Report NLR TR 77103 U. NLR, Amsterdam (1977)Google Scholar
  24. Schijve, J., Campoli, G., Monaco, A.: Fatigue of structures and secondary bending in structural elements. Int. J. Fatigue 31, 1111–1123 (2009)CrossRefGoogle Scholar
  25. Schra, L., Ottens, H.H., Vlieger, H.: Fatigue crack growth in simulated Fokker 100 lap joints under MSD and SSD conditions. Report NLR CR 95729 C. NLR, Amsterdam (1995)Google Scholar
  26. Schütz, D., Lowak, H.: Die Berücksichtigung des Einflusses der Sekundär-Biegung auf die Schwingfestigkeit von Fügungen. Bericht Nr FB-113. Laboratorium für Betriebsfestigkeit, Darmstadt (1974). Also available as: Schütz, D., Lowak, H.: The effect of secondary bending on the fatigue strength of joints. Report FB-113. Laboratorium für Betriebsfestigket, Darmstadt (1974), RAE Library Translation No. 185Google Scholar
  27. Skorupa, M., Korbel, A.: Modelling the secondary bending in riveted joint with eccentricities. Arch. Mech. Eng. 55, 335–352 (2008)Google Scholar
  28. Skorupa, M., Skorupa, A., Machniewicz, T., Korbel, A.: An experimental investigation on the fatigue performance of riveted lap joint. In: Boss, M.J. (ed.) Proceedings of 25th ICAF Symposium, Bridging the Gap between Theory and Practice, Rotterdam, The Netherlands, 27–29 May 2009, pp. 449–473. Springer, Dordrecht/Heidelberg/London/New York (2009)Google Scholar
  29. Skorupa, M., Skorupa, A., Machniewicz, T., Korbel, A.: Effect of production variables on the fatigue behaviour of riveted lap joints. Int. J. Fatigue 32, 996–1003 (2010b)CrossRefGoogle Scholar
  30. Skorupa, M., Skorupa, A., Machniewicz, T., Korbel, A.: Improving the fatigue performance of riveted joints in airframes. Final report on EUREKA project IMPERJA, No. E!3496. University of Science and Technology AGH, Kraków (2011) (in Polish, unpublished results)Google Scholar
  31. Starikow, R.: Mechanically fastened joints. Critical testing of single overlap joints. Scientific Report FOI-R-0441-SE. Swedish Defense Research Agency, Aeronautics Division, FAA, Stockholm (2002)Google Scholar
  32. Wanhill, R.J.H.: Some practical considerations for fatigue and corrosion damage assessment of ageing aircraft. Report NLR TP 96253 L. NLR, Amsterdam (1996)Google Scholar
  33. Wit, G.P.: Bending stresses in circumferential fuselage joints (3-D modeling). T.D. No. SCM-099, Fokker, Stress Office Technical Data Sheet (Aug 1993)Google Scholar

Copyright information

© Springer Science+Business Media Dordrecht 2012

Authors and Affiliations

  • Andrzej Skorupa
    • 1
  • Małgorzata Skorupa
    • 1
  1. 1.Faculty of Mechanical Engineering and RoboticsAGH University of Science and TechnologyKrakówPoland

Personalised recommendations