Advertisement

Experimental Estimation of Influence of Fuel Injector Nozzle Design on Output Parameters of Tractor Diesel

  • G. V. Lomakin
  • V. E. Lazarev
  • V. M. Myslyaev
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

It has been experimentally established that the modification of the spray nozzle structure of the diesel fuel injector due to the reduction of the length from 18 mm to 10 mm and the diameter from 6 mm to 4 mm of the precision guide, the increase in the diameter of the needle rod to increase its rigidity, the development of the cooling cavity under the differential needle pad increasing the number of fuel supply channels from 3 to 5, increasing the fuel injection pressure from 21–22 MPa to 27–28 MPa and reducing the needle stroke from 0.45 mm to 0.35 mm affects the power and economic parameters of tractor dies spruce. The use of experimental sprayers in a tractor diesel with gas turbine supercharging makes it possible to reduce the specific fuel consumption by 2–6 g/kW h and the temperature of the exhaust gases by 30–50 °C depending on the loading regime, as well as some increases (up to 2%) the coefficient of adaptability for torque. Using sprayers of experimental design in diesel with gas turbine supercharging allows to reduce the specific effective fuel consumption by 2–6 g/kW h and exhaust gas temperature by 30–50 °C depending on the loading mode, also some increase (up to 2%) of the coefficient of adaptability for the torque is registered.

Keywords

Injector Precision-guiding interface Moment of injection of the fuel Velocity and loading characteristics Fuel consumption Temperature of the exhaust gases 

Notes

Acknowledgements

The work was supported by the Ministry of Education and Science of the Russian Federation under the Mikhail Lomonosov program (publication number: 9.9996.2017/5.2), and the German Academic Exchange Service DAAD (Linie B, 2017 (57320204), project 91580049) and was carried out jointly with the Institute of Internal Combustion Engines of the Munich Technical University (Munich, Germany).

References

  1. 1.
    Moser, Franz K (2009) Tendencies and solutions in the development of commercial diesel engines. Paper presented at the international scientific and technical conference “turbocharging of automotive and tractor engines”, 24–25 June 2009Google Scholar
  2. 2.
    Lazarev EA (2010) Basic principles, methods and efficiency of tools for combustion process improving for increasing the technical level of tractor diesel engines, ChelyabinskGoogle Scholar
  3. 3.
    Smailys VI (1991) The current status and new problems of the ecology of diesel engine construction. Engine Build 1:3–6Google Scholar
  4. 4.
    Zvonov VA (1981) Toxicity of internal combustion engines, MoscowGoogle Scholar
  5. 5.
    Markov VA (2007) Injection and spraying of fuel in diesel engines, MoscowGoogle Scholar
  6. 6.
    Markov VA (2002) Toxicity of diesel engines’ exhaust gases, MoscowGoogle Scholar
  7. 7.
    Fainleib BN (1990) Fuel equipment of autotractor diesels: reference book. 2 edn. St. PetersburgGoogle Scholar
  8. 8.
    Rev techn Diesel (1989) Fuel nozzles and sprayers of modern autotractor diesels. Les porte-injecteurs et injeteurs 158:11–25Google Scholar
  9. 9.
    Gorbanevsky VE, Kislov VG et al (1996) Diesel fuel equipment. Optimization of the injection process, details and friction pairs longevity, MoscowGoogle Scholar
  10. 10.
    Golev VI (1989) Runout of locking cones and forecasting of the sprayers’ operational life of autotractor diesels. Engine Build 12:20–23Google Scholar
  11. 11.
    Mikulin YV (1986) Comprehensive solution of increasing the resource issue and improving the reliability issue of diesel fuel equipment. Engine Build 10:58–60Google Scholar
  12. 12.
    Zhdanovsky NS (1981) Reliability and operational life of autotractor engines, St. PetersburgGoogle Scholar
  13. 13.
    Lazarev VE (2003) Sprayer’s parameters and characteristics used in assessing the reasons for the reduced efficiency of the diesel fuel injector. Bull SUSU Ser Mech Eng 1(17):33–36Google Scholar
  14. 14.
    Nikolaenko AV, Belyakov VV et al (1979) Improving the reliability of diesel injectors sprayers by vibrating the cylindrical needle surface guide. Drive Eng 4:31–33Google Scholar
  15. 15.
    Chainov ND (1977) Thermomechanical tension of engine parts, MoscowGoogle Scholar
  16. 16.
    Lazarev VE, Malozemov AA et al (2007) A method for estimating the runout rate and the life of a precision fitting of a fuel sprayer in a diesel engine. Drive Eng 3:26–29Google Scholar
  17. 17.
    Lazarev VE, Lomakin GV et al (2009) The sprayer nozzle. RF patent 86668 U1, IPC F 02 M 49/00, 9 Sept 2009Google Scholar
  18. 18.
    Rusinov RV, Gerasimov IM et al (2000) On the reliability of the sprayers operation. Drive Eng 3:16–17Google Scholar
  19. 19.
    Lazarev VE (2010) Increasing the resource of fuel sprayers in diesel engines by reducing the loading and runout intensity of precision couplings: monograph, ChelyabinskGoogle Scholar
  20. 20.
    Lazarev VE, Lomakin GV et al (2009) Reduction of the thermal and hydrodynamic loading of the guide coupling “needle-body” of the sprayer. Bull SUSU Ser Eng 33(166):76–80Google Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  • G. V. Lomakin
    • 1
  • V. E. Lazarev
    • 1
  • V. M. Myslyaev
    • 1
  1. 1.South Ural State UniversityChelyabinskRussia

Personalised recommendations