Advertisement

The Effect of Chamber Temperature on Residual Stresses of FDM Parts

  • C. Casavola
  • A. Cazzato
  • D. Karalekas
  • V. Moramarco
  • G. Pappalettera
Conference paper
Part of the Conference Proceedings of the Society for Experimental Mechanics Series book series (CPSEMS)

Abstract

The Fused Deposition Modelling (FDM) is nowadays one of the most widespread and employed processes to build complex 3D prototypes directly from a STL model. In this technique, the part is built as a layer-by-layer deposition of a feedstock wire. This typology of deposition has many advantages but it produces rapid heating and cooling cycles of the feedstock material that introduces residual stresses in the part during the building-up. Consequently, warping, de-layering and distortion of the part during the print process are common issues in FDM parts and are related to residual stresses. In the view to reduce this kind of issues, the high-level print systems use a heated chamber. The aim of the present work is to measure the residual stresses in several points of the printed parts, both on top and bottom, in order to verify if the use of the heated chamber during the printing produce substantial variation. The residual stresses have been measured in ABS parts employing the hole-drilling method. In order to avoid the local reinforcement of the strain gage, an optical technique, i.e. ESPI (electronic speckle pattern interferometry), is employed to measure the displacement of the surface due to the stress relaxation and, consequently, to calculate the residual stresses.

Keywords

3D printing Residual stress Fused deposition modelling Hole drilling ESPI 

References

  1. 1.
    Yan, X., Gu, P.: A review of rapid prototyping technologies and systems. Comput. Aided Des. 28(4), 307–318 (1996)CrossRefGoogle Scholar
  2. 2.
    Petzold, R., Zeilhofer, H.F., Kalender, W.A.: Rapid prototyping technology in medicine—basics and applications. Comput. Med. Imaging Graph. 23(5), 277–284 (1999)CrossRefGoogle Scholar
  3. 3.
    Chua, C.K., Chou, S.M., Wong, T.S.: A study of the state-of-the-art rapid prototyping technologies. Int. J. Adv. Manuf. Technol. 14(2), 146–152 (1998)CrossRefGoogle Scholar
  4. 4.
    Barile, C., et al.: Mechanical characterization of SLM specimens with speckle interferometry and numerical optimization. Conf. Proc. Soc. Exp. Mech. Ser. 6, 837–843 (2011)CrossRefGoogle Scholar
  5. 5.
    Casavola, C., et al.: Orthotropic mechanical properties of fused deposition modelling parts described by classical laminate theory. Mater. Des. 90, 453–458 (2016)CrossRefGoogle Scholar
  6. 6.
    Mireles, J., et al.: Development of a fused deposition modeling system for low melting temperature metal alloys. J. Electron. Packag. 135(1), 011008–011008 (2013)CrossRefGoogle Scholar
  7. 7.
    Allahverdi, M., et al.: Processing of advanced electroceramic components by fused deposition technique. J. Eur. Ceram. Soc. 21(10–11), 1485–1490 (2001)CrossRefGoogle Scholar
  8. 8.
    Zein, I., et al.: Fused deposition modeling of novel scaffold architectures for tissue engineering applications. Biomaterials. 23(4), 1169–1185 (2002)CrossRefGoogle Scholar
  9. 9.
    Masood, S.H., Song, W.Q.: Development of new metal/polymer materials for rapid tooling using fused deposition modelling. Mater. Des. 25(7), 587–594 (2004)CrossRefGoogle Scholar
  10. 10.
    Zhong, W., et al.: Short fiber reinforced composites for fused deposition modeling. Mater. Sci. Eng. A. 301(2), 125–130 (2001)CrossRefGoogle Scholar
  11. 11.
    Kantaros, A., Karalekas, D.: Fiber Bragg grating based investigation of residual strains in ABS parts fabricated by fused deposition modeling process. Mater. Des. 50, 44–50 (2013)CrossRefGoogle Scholar
  12. 12.
    Casavola, C., et al.: Preliminary study on residual stress in FDM parts. In: Residual Stress, Thermomechanics & Infrared Imaging, Hybrid Techniques and Inverse Problems, vol. 9, pp. 91–96. Springer International Publishing, New York LLC (2017)Google Scholar
  13. 13.
    Casavola, C., et al.: Residual stress measurement in fused deposition modelling parts. Polym. Test. 58, 249–255 (2017)CrossRefGoogle Scholar
  14. 14.
    Casavola, C., et al.: Influence of printing constraints on residual stresses of FDM parts. Conf. Proc. Soc. Exp. Mech. Ser. 8, 121–127 (2018)CrossRefGoogle Scholar
  15. 15.
    Turnbull, A., Maxwell, A.S., Pillai, S.: Residual stress in polymers - evaluation of measurement techniques. J. Mater. Sci. 34(3), 451–459 (1999)CrossRefGoogle Scholar
  16. 16.
    Nau, A., et al.: Application of the hole drilling method for residual stress analyses in components made of polycarbonate. Zeitschrift Kunststofftechnik/J. Plastics Technol. 2011(3), 66–85 (2011)Google Scholar
  17. 17.
    Magnier, A., A. Nau, B. Scholtes. Some aspects of the application of the hole drilling method on plastic materials, in Conference Proceedings of the Society for Experimental Mechanics Series, (2016)Google Scholar
  18. 18.
    Zhang, Y., Chou, Y.: Three-dimensional finite element analysis simulations of the fused deposition modelling process. Proc. Inst. Mech. Eng. B J. Eng. Manuf. 220(10), 1663–1671 (2006)CrossRefGoogle Scholar
  19. 19.
    Barile, C., et al.: Drilling speed effects on accuracy of HD residual stress measurements. Conf. Proc. Soc. Exp. Mech. Ser. 8, 119–125 (2014)CrossRefGoogle Scholar
  20. 20.
    Barile, C., et al.: Residual stress measurement by electronic speckle pattern interferometry: a study of the influence of geometrical parameters. Struct. Integrity Life. 11(3), 177–182 (2011)Google Scholar
  21. 21.
    Kujawinska, M.: Use of phase-stepping automatic fringe analysis in moire interferometry. Appl. Opt. 26(22), 4712–4714 (1987)CrossRefGoogle Scholar
  22. 22.
    Ghiglia, D.C., Pritt, M.D.: Two-Dimensional Phase Unwrapping: Theory, Algorithms, and Software, vol. 4. Wiley, New York (1998)zbMATHGoogle Scholar

Copyright information

© The Society for Experimental Mechanics, Inc. 2019

Authors and Affiliations

  • C. Casavola
    • 1
  • A. Cazzato
    • 1
  • D. Karalekas
    • 2
  • V. Moramarco
    • 1
  • G. Pappalettera
    • 1
  1. 1.Dipartimento di MeccanicaMatematica e Management (DMMM) – Politecnico di BariBariItaly
  2. 2.Laboratory of Advanced Manufacturing Technologies and TestingUniversity of PiraeusPiraeusGreece

Personalised recommendations