Mediterranean Green Buildings & Renewable Energy pp 445-464 | Cite as

# Bi-fluid Photovoltaic/Thermal PV/T Solar Collector with Three Modes of Operation: Experimental Validation of a Theoretical Model

## Abstract

This chapter discusses theoretical and indoor experimental studies of a bi-fluid type photovoltaic/thermal (PV/T) solar collector. Two-dimensional steady-state analysis was developed and computer simulations were performed using MATLAB. Experiments were conducted for steady-state analysis under the solar simulator at Solar Energy Research Lab UiTM, Perlis, Malaysia, and under real sky conditions of Northern Peninsular Malaysia, to validate the model. The solar collector and the test rig facilities were fabricated to be suitable for mathematical validation purposes in both indoor and outdoor testing. For indoor collector testing, at an average wind speed of 1 m/s and average solar radiation of 700 W/m^{2}, the air and water mass flow rate was varied from 0.0074 to 0.09 kg/s and 0.0017 to 0.0265 kg/s respectively. The thermal efficiency increased as the mass flow rate increased. At a mass flow rate of 0.0262 and 0.0066 kg/s for air and water respectively, the thermal efficiency curves tended to plateau, which marked the optimum point of the fluid flow. For the simultaneous mode of fluid operation, testing was conducted with air and water fixed at a flow rate of 0.0262 and 0.0066 kg/s respectively, while the fluids’ mass flow rate was varied according to the range used during the independent mode. The range of the computed efficiencies for the simultaneous mode were higher than for the independent mode. In this study, collector outdoor testing was conducted for each mode of operation on a typical day in January in Perlis, Northern Peninsular Malaysia. Based on the outdoor monitoring analysis for simultaneous mode, the performance of the collector was also higher overall than the independent mode. The test was conducted by monitoring the performance of the collector with the air mass flow rate and water mass flow rate fixed at 0.0262 and 0.0066 kg/s respectively. Theoretical analysis was also performed and then validated against the experimental results by a direct comparison of the plotted curves and using mean absolute percentage error (MAPE) analysis. For the air, water and simultaneous modes, by taking into account both indoor and outdoor collector testing, the theoretical and experimental curves were found to be in good agreement, and the computed MAPE values for the fluids’ output temperature were less than 2 %. Thus, the two-dimensional mathematical model was proven valid. The PV/T collector designed in this study has a variety of applications because it can be operated in three different modes of fluid operation, and the theoretical model is useful in modelling all three modes without further modification.

## Keywords

Photovoltaic/thermal 2D analysis Bi-fluid Indoor Outdoor## Nomenclature

*A*_{PV}Collector aperture area’s subsegment, which is equal to the area of the PV module’s subsegment (m

^{2})*C*_{f}Conversion power factor

*C*_{pf1}Specific heat capacity of air

*C*_{pf2}Specific heat capacity of water

*D*_{i}Inner pipe diameter

*D*_{o}Outer pipe diameter

*f*A General subscript to represent a fluid

*f*_{r}A Friction factor in a fluid’s channel

*G*Global radiation

*h*Heat transfer coefficient (W/m

^{2}K)*h*_{cvbs f1}Convection heat transfer coefficient from back surface of Tedlar to air flow (W/m

^{2}K)*h*_{cvbs f2}Convection heat transfer coefficient from back surface of Tedlar to water flow (W/m

^{2}K)*h*_{cvfin f1}Convection heat transfer coefficient from surface of a fin to flowing air (W/m

^{2}K)*h*_{cvw}Wind convection heat transfer coefficient (W/m

^{2}K)*h*_{i}Generalised notation for heat transfer coefficient of linear equations derived from developed energy balance equations for general heat transfer coefficient

*i*(W/m^{2}K)*h*_{rbsbp}Radiation heat transfer coefficient between inner surfaces of collector (W/m

^{2}K)*h*_{rpvsky}Radiation heat transfer coefficient from PV cells to sky (W/m

^{2}K)*k*_{fin}Thermal conductivity of fin (W/mK)

*k*_{f1}Thermal conductivity of air (W/mK)

*k*_{f2}Thermal conductivity of water (W/mK)

*k*_{PV}Thermal conductivity of photovoltaic cells (W/mK)

*L*_{fin}Length of fin (m)

*m*Subsegment for each temperature node

- \( {\overset{.}{m}}_{f1} \)
Air mass flow rate (kg/s)

- \( {\overset{.}{m}}_{f2} \)
Water mass flow rate (kg/s)

*N*_{fin}Total number of fins

*q*Rate of heat flux (W/m

^{2})*q*_{uf1, m}Rate of heat transfer per unit area for air nodes (W/m)

*q*_{uf2, m}Rate of heat transfer per unit area for air nodes (W/m)

*Re*Reynolds number

*S*_{PV}Total rate of solar energy absorbed by solar cells of PV module

*S*_{T}Total energy absorbed by Tedlar

*T*Temperature (K)

*T*_{a}Ambient temperature (K)

*T*_{bp, m}Temperature nodes of surface of back plate (K)

*T*_{bs, m}Temperature nodes of rear surface of Tedlar (K)

*T*_{bp}Mean temperature of surface of back plate with fins (K)

*T*_{bs}Mean temperature of rear surface of Tedlar (K)

*T*_{PV}Mean temperature of cell (K)

*T*_{f1, m}Temperature nodes of air flow in channel (K)

*T*_{f2, m}Temperature nodes of water flow in copper pipe (K)

*T*_{fin, m}Mean temperature of fin at subsegment

*m*(K)*T*_{PV, m}Temperature nodes of PV cells (at centre of cells) (K)

*T*_{ref}Temperature at reference point

*T*_{sky}Sky temperature (K)

*T*_{tin}Mean inner wall temperature of copper pipe (K)

*U*_{t, m}Overall top heat loss coefficient for subsegment

*m**v*_{f1}Maximum velocity of air (m/s)

*v*_{w}Wind speed (m/s)

*W*Tube spacing (m)

*α*_{c}Absorptance of PV cells

*β*_{c}PV module packing factor

*β*_{ref}Temperature coefficient at reference temperature

*δ*_{PV}Thickness of PV module

*δ*_{si}Thickness of Si cells

*δ*_{T}Thickness of Tedlar layer

*δ*_{fin}Fin thickness

- Δ
*y*_{PV}Δ*x* Area of subsegment of PV module

- Δ
*x* Distance between temperature nodes (\( \Delta x=1\ \mathrm{cm} \))

*ε*_{sky}Emissivity of sky

*ε*_{g}Emissivity of glass cover

*γ*_{bsbp, m}Area correction factor for heat transfer from back surface of Tedlar to surface of back plate with fins

*γ*_{bs f1, m}Area correction factor for heat transfer from back surface of Tedlar to flowing air

*γ*_{bs f2, m}Area correction factor for heat transfer from back surface of Tedlar to flowing water

*γ*_{fin f1, m}Area correction factor for heat transfer from fin surfaces to flowing air

*γ*_{bp f1, m}Area correction factor for heat transfer from surface of back plate with fins to flowing air

*γ*_{bpa, m}Area correction factor for heat transfer from surface of back plate with fins to ambient

*τ*_{g}Transmittance factor of front cover glass of PV module

*τ*_{gg}Transmittance factor due to double glazing (glass covers)

*η*Efficiency

*η*_{c}Electrical efficiency of a PV cell

*η*_{ele}Electrical efficiency

*η*_{eth}Electrical efficiency converted to equivalent thermal efficiency

*η*_{fin}Fin efficiency

*η*_{p}Fin effectiveness

*η*_{Tref}Electrical efficiency at reference temperature

*η*_{th f1}Thermal efficiency of air

*η*_{th f2}Thermal efficiency of water

- \( \sum {\eta}_{\mathrm{th}} \)
Total thermal efficiency of solar collector

- \( \sum {\eta}_{\mathrm{PVT}} \)
Primary energy saving or equivalent thermal efficiency

- \( \sum {\eta}_{\mathrm{th},\mathrm{inst}} \)
Instantaneous total thermal efficiency of solar collector

## Notes

### Acknowledgement

This work was funded by the Malaysian Fundamental Research Group (FRGS) 600-RMI/ST/FRGS 5/3/Fst (160/2010) and Solar Energy Research Lab, Universiti Teknologi Mara (UiTM), Perlis, Malaysia

## References

- 1.Abdul Hamid S, Yusof Othman M, Sopian K, Zaidi SH (2014) An overview of photovoltaic thermal combination (PV/T combi) technology. Renew Sustain Energy Rev 38:212–222CrossRefGoogle Scholar
- 2.Zondag HA, de Vries DW, van Helden WGJ, van Zolingen RJC, van Steenhoven AA (2002) The thermal and electrical yield of a PV-thermal collector. Sol Energy 72:113–128CrossRefGoogle Scholar
- 3.Dubey S, Sandhu GS, Tiwari GN (2009) Analytical expression for electrical efficiency of PV/T hybrid air collector. Appl Energy 86:697–705CrossRefGoogle Scholar
- 4.Solanki SC, Dubey S, Tiwari A (2009) Indoor simulation and testing of photovoltaic thermal (PV/T) air collectors. Appl Energy 86:2421–2428CrossRefGoogle Scholar
- 5.Tiwari A, Sodha MS (2007) Parametric study of various configurations of hybrid PV/thermal air collector: experimental validation of theoretical model. Sol Energy Mater Sol Cells 91:17–28CrossRefGoogle Scholar
- 6.Tiwari A, Sodha MS (2006) Performance evaluation of solar PV/T system: an experimental validation. Sol Energy 80:751–759CrossRefGoogle Scholar
- 7.Tonui JK, Tripanagnostopoulos Y (2007) Air-cooled PV/T solar collectors with low cost performance improvements. Sol Energy 81:498–511CrossRefGoogle Scholar
- 8.Koech RK, Ondieki HO, Tonui JK, Rotich SK (2012) A Steady State Thermal Model For Photovoltaic/Thermal (PV/T) System Under Various Conditions. Int J Sci Technol Res 1Google Scholar
- 9.Dehra H (2009) A two dimensional thermal network model for a photovoltaic solar wall. Sol Energy 83:1933–1942CrossRefGoogle Scholar
- 10.Assoa YB, Menezo C, Fraisse G, Yezou R, Brau J (2007) Study of a new concept of photovoltaic–thermal hybrid collector. Sol Energy 81:1132–1143CrossRefGoogle Scholar
- 11.Tripanagnostopoulos Y (2007) Aspects and improvements of hybrid photovoltaic/thermal solar energy systems. Sol Energy 81:1117–1131CrossRefGoogle Scholar
- 12.Abu Bakar MN, Othman M, Hj Din M, Manaf NA, Jarimi H (2014) Design concept and mathematical model of a bi-fluid photovoltaic/thermal (PV/T) solar collector. Renew Energy 67:153–164CrossRefGoogle Scholar
- 13.Manaf NA, Bakar A, Nazari M, Jarimi H, Muhamed S, Othman M (2013) Design of a single-pass bi-fluid Photovoltaic/Thermal (PV/T) solar collector. Int J Chem Environ Eng 4Google Scholar
- 14.Abu Bakar MN, Othman M, Hj Din M, Manaf NA, Jarimi H (2013) Development of an improved photovoltaic/thermal (PV/T) solar collector with bi-fluid configuration. Int J Chem Environ Eng 4Google Scholar
- 15.Jarimi H, Bakar MNA, Othman M, Din MH, Manaf NA (2014) Investigation on the thermal characteristics of a bi-fluid type hybrid solar collector. In World Renewable Energy Congress 2014, Kingston, LondonGoogle Scholar
- 16.Jarimi H, Abu Bakar MN, Manaf NA, Othman M, Din M (2013) Mathematical modelling of a finned bi-fluid type photovoltaic/thermal (PV/T) solar collector. In IEEE Conference on Clean Energy and Technology (CEAT), 2013, pp 163–168Google Scholar
- 17.Chow TT, Pei G, Fong KF, Lin Z, Chan ALS, Ji J (2009) Energy and exergy analysis of photovoltaic–thermal collector with and without glass cover. Appl Energy 86:310–316CrossRefGoogle Scholar
- 18.Lawan SM, Abidin WAWZ, Chai WY, Baharun A, Masri T (2013) Reviewing wind speed and energy distribution in Malaysia. Eur Acad Res 1:2104–2122Google Scholar
- 19.Garg HP, Shukla AR, Madhuri I, Agnihotri RC, Chakravertty S (1985) Development of a simple low-cost solar simulator for indoor collector testing. Appl Energy 21:43–54CrossRefGoogle Scholar
- 20.Abu Bakar MN, Hj Othman MY (2013) Teknologi pengumpul suria fotovolta terma. Penerbit Universiti Kebangsaan Malaysia, MalaysiaGoogle Scholar
- 21.Hussain F, Othman MYH, Yatim B, Ruslan H, Sopian K, Anuar Z et al (2011) Fabrication and irradiance mapping of a Low cost solar simulator for indoor testing of solar collector. J Sol Energy Eng 133:044502CrossRefGoogle Scholar
- 22.Agrawal S, Tiwari GN, Pandey HD (2012) Indoor experimental analysis of glazed hybrid photovoltaic thermal tiles air collector connected in series. Energy Build 53:145–151CrossRefGoogle Scholar
- 23.Fudholi A, Sopian K, Othman MY, Ruslan MH, Bakhtyar B (2013) Energy analysis and improvement potential of finned double-pass solar collector. Energy Convers Manag 75:234–240CrossRefGoogle Scholar
- 24.Othman MY, Yatim B, Sopian K, Abu Bakar MN (2007) Performance studies on a finned double-pass photovoltaic-thermal (PV/T) solar collector. Desalination 209:43–49CrossRefGoogle Scholar
- 25.Ong KS (1995) Thermal performance of solar air heaters: mathematical model and solution procedure. Sol Energy 55:93–109CrossRefGoogle Scholar
- 26.Yaws CL, Richmond PC (2009) Appendix B—thermophysical and transport properties of water. In: Yaws CL (ed) Thermophysical properties of chemicals and hydrocarbons. William Andrew Publishing, Norwich, pp 791–799CrossRefGoogle Scholar
- 27.Huang BJ, Lin TH, Hung WC, Sun FS (2001) Performance evaluation of solar photovoltaic/thermal systems. Sol Energy 70:443–448CrossRefGoogle Scholar
- 28.Suruhanjaya Tenaga (Energy Comissions) (2012) Industri Pembekalan Elektrik di Malaysia Maklumat dan Prestasi Statistik 2012. ed. Putrajaya Malaysia: Suruhanjaya Tenaga (Energy Comissions)Google Scholar
- 29.Manglik RM, Bergles AE (1995) Heat transfer and pressure drop correlations for the rectangular offset strip fin compact heat exchanger. Exp Therm Fluid Sci 10(2):171–180, http://dx.doi.org/10.1016/0894-1777(94)00096-Q CrossRefGoogle Scholar
- 30.Tam LM, Ghajar AJ (2006) Transitional heat transfer in plain horizontal tubes. Heat Transfer Eng 27:23–38CrossRefGoogle Scholar
- 31.Gnielinski V (1976) New equations for heat and mass transfer in turbulent pipe and channel flow. Int Chem Eng 16:359–368Google Scholar
- 32.Lin W, Gao W, Liu T (2006) A parametric study on the thermal performance of cross-corrugated solar air collectors. Appl Therm Eng 26:1043–1053CrossRefGoogle Scholar
- 33.Çengel YA, Ghajar AJ, Kanoğlu M (2011) Heat and mass transfer: fundamentals and applications. McGraw Hill Higher Education, New YorkGoogle Scholar
- 34.Moradi K, Ali Ebadian M, Lin C-X (2013) A review of PV/T technologies: effects of control parameters. Int J Heat Mass Transf 64:483–500CrossRefGoogle Scholar
- 35.Joshi AS, Tiwari A, Tiwari GN, Dincer I, Reddy BV (2009) Performance evaluation of a hybrid photovoltaic thermal (PV/T) (glass-to-glass) system. Int J Therm Sci 48:154–164CrossRefGoogle Scholar
- 36.Sarhaddi F, Farahat S, Ajam H, Behzadmehr A, Mahdavi Adeli M (2010) An improved thermal and electrical model for a solar photovoltaic thermal (PV/T) air collector. Appl Energy 87:2328–2339CrossRefGoogle Scholar
- 37.Amori KE, Taqi Al-Najjar HM (2012) Analysis of thermal and electrical performance of a hybrid (PV/T) air based solar collector for Iraq. Appl Energy 98:384–395CrossRefGoogle Scholar

## Copyright information

<SimplePara><Emphasis Type="Bold">Open Access</Emphasis> This chapter is licensed under the terms of the Creative Commons Attribution-NonCommercial 2.5 International License (http://creativecommons.org/licenses/by-nc/2.5/), which permits any noncommercial use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license and indicate if changes were made. </SimplePara> <SimplePara>The images or other third party material in this chapter are included in the chapter's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the chapter's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.</SimplePara>