Advertisement

Analysis of Indirect Measurement of Cutting Forces Turning Metal Cylindrical Shells

  • Kirill KondratenkoEmail author
  • Alexandre Gouskov
  • Mikhail Guskov
  • Philippe Lorong
  • Grigory Panovko
Conference paper
Part of the Mechanisms and Machine Science book series (Mechan. Machine Science, volume 23)

Abstract

Cutting forces measurement is an important component of the machining processes development and control. The use of conventional direct measurement systems is often impossible as they interfere in the process’s dynamics. This work proposes a method of cutting force indirect estimation during turning thin-walled cylindrical shells. Calculation of the flexibility matrix has enabled us to relate measured displacements of certain workpiece’s points to the cutting force. An optimization approach for choosing the measurement points location has been proposed, based on the best conditioning of the flexibility matrix.

Keywords

Cutting forces measurement Thin-walled workpiece Technological system Optimization Ill-conditioned systems 

References

  1. 1.
    Fang N, Wu Q (2009) A comparative study of the cutting forces in high speed machining of Ti-6Al-4 V and Inconel 718 with a round cutting edge tool. J Mater Process Technol 209(9):4385–4389CrossRefGoogle Scholar
  2. 2.
    Sun S, Brandt M, Dargusch MS (2009) Characteristics of cutting forces and chip formation in machining of titanium alloys. Int J Mach Tools Manuf 49(7–8):561–568Google Scholar
  3. 3.
    Kim T-Y, Kim J (1996) Adaptive cutting force control for a machining center by using indirect cutting force measurements. Int J Mach Tools Manuf 36(8):925–937Google Scholar
  4. 4.
    Lorong P, Larue A, Duarte AP (2011) Dynamic study of thin wall part turning. Adv Mater Res 223:591–599 doi: 10.4028/www.scientific.net/AMR.223.591
  5. 5.
    Biderman VL (1997) Mekhanika tonkostennykh konstruktsiy. MoscowGoogle Scholar
  6. 6.
    Kondratenko KE, Gouskov AM, Guskov MA, Lorong. P, Panovko GY (2014) Analysis of indirect measurement of cutting forces in turning metal cylindrical shells. Vestnik MGTU imeni Baumana. doi: 10.7463/0214.0687971
  7. 7.
    Godunov SK (1961) On the numerical solution of boundary value problems for systems of linear ordinary differential equations. Uspehi Mat Nauk 16:171–174zbMATHMathSciNetGoogle Scholar
  8. 8.
    Higham NJ (2002) Accuracy and stability of numerical algorithms, 2nd edn. SIAM, PhiladelphiaCrossRefzbMATHGoogle Scholar
  9. 9.
    Householder AS (1958) Unitary triangularization of a nonsymmetric matrix. J ACM 5(4):339–342. doi: 10.1145/320941.320947 CrossRefzbMATHMathSciNetGoogle Scholar
  10. 10.
    Gerasimenko AA, Gouskov AM, Guskov MA, Lorong P (2012) Spinning shell eigen modes calculation. Vestnik MGTU imeni BaumanaGoogle Scholar

Copyright information

© Springer International Publishing Switzerland 2015

Authors and Affiliations

  • Kirill Kondratenko
    • 1
    Email author
  • Alexandre Gouskov
    • 1
    • 2
  • Mikhail Guskov
    • 3
  • Philippe Lorong
    • 3
  • Grigory Panovko
    • 4
  1. 1.Department RC5Bauman Moscow State Technical UniversityMoscowRussia
  2. 2.National Research Centre “Kurtchatovsky Institute”MoscowRussia
  3. 3.ENSAM-ParisTechParisFrance
  4. 4.IMASH RSAMoscowRussia

Personalised recommendations