Rock Physics and Natural Hazards pp 1011-1036 | Cite as
Laboratory Characterization of Permeability and Its Anisotropy of Chelungpu Fault Rocks
Abstract
In Taiwan an international project to drill into the Chelungpu fault (TCDP) was initiated after the M w7.6 Chi-Chi earthquake in 1999. At Takeng, two vertical holes (A and B) to depths of about 2 km have been drilled through the northern portion of the Chelungpu fault system. In this study, we conducted systematic hydromechanical tests on TCDP drillcores collected from Hole-A at various depths above and below the major slip zone of the Chelungpu fault. We focus on the measurements of permeability as function of pressure and the brittle failure behavior. Evolution of permeability as a function of pressure and porosity was measured using either steady-state flow or a pulse transient technique. When subjected to an effective pressure reaching 100 MPa, permeability values of shaly siltstone samples range from 10−16 to 10−19 m2. In comparison, permeability values of porous sandstones are at least an order of magnitude higher, ranging from 10−14 to 10−18 m2. To characterize permeability anisotropy associated with the bedding structure of the rocks of the Chelungpu fault, cylindrical samples were taken from the TCDP drillcores along three orthogonal directions, denoted X, Y and Z respectively. Direction Z is parallel to the TCDP core axis, and the other two directions are perpendicular to the core axis, with X (N105°E) perpendicular and Y (N15°E) parallel to the strike of the bedding. In shaly siltstones, permeability values of samples cored along the strike of bedding (direction Y) can be up to 1 order of magnitude higher than those cored perpendicular to the strike of bedding (direction X). These observations indicate that permeability anisotropy is controlled by the spatial distribution of bedding in Chelungpu fault host rocks. Permeability evolution of fault rocks plays an important role in dynamic weakening processes, which are particularly pertinent to large earthquakes such as the Chi-Chi earthquake. Our experimental data on permeability and its anisotropy of TCDP core samples provide necessary constraints on fault models and proposed weakening mechanisms.
Key words
Permeability and porosity Chelungpu fault bedding anisotropy deformation tests dynamic weakeningPreview
Unable to display preview. Download preview PDF.
References
- Andrews, D.J. (2002), A fault constitutive relation accounting for thermal pressurization of pore fluid, J. Geophys. Res. 107(B12), 2363, doi: 10.1029/2002JB001942.CrossRefGoogle Scholar
- Brodsky, E.E. and Kanomori, H. (2001), Elastohydrodynamic lubrication of faults, J. Geophys. Res. 106, 16357–16374.CrossRefGoogle Scholar
- Caine, J.S., Evans, J.P., and Forster, C.B. (1996), Fault zone architecture and permeability structure, Geology 24, 1025–1028.CrossRefGoogle Scholar
- Chen, T.-M.N., Experimental Constraint on Hydromechanical Properties and Microcrack Fabric of Core Samples from the Taiwan Chelungpu-Fault Drilling Project, Master Thesis, Stony Brook Univ., New York (2008).Google Scholar
- Chester, F.M. and Logan, J.M. (1986), Composite planar fabric of gouge from the punchbowl fault, California, J. Struct. Geol. 9, 621–634.CrossRefGoogle Scholar
- David, C., Wong, T.-F., Zhu, W., and Zhang, J. (1994), Laboratory measurement of compaction-induced permeability change in porous rocks: Implications for the generation and maintenance of pore pressure excess in the crust, Pure Appl. Geophys. 143, 425–456.CrossRefGoogle Scholar
- Evans, J.P., Forster, C.B., and Goddard, J.V. (1997), Permeability of fault-related rocks, and implications for hydraulic structure of fault zones, J. Struct. Geol. 19, 1393–1404.CrossRefGoogle Scholar
- Faulkner, D.R., Lewis, A.C., and Rutter, E.H. (2003), On the internal structure and mechanics of large strikeslip zones: Field observations of the Carboneras fault in southeast Spain, Tectonophysics 367, 235–251.CrossRefGoogle Scholar
- Hirono T., Yeh, E.-C., Lin, W., Sone, H., Mishima, T., Soh, W., Hashimoto, Y., Matsubayashi, O., Aoike, K., Ito, H., Kinoshita, M., Murayama, M., Song, S.-R., Ma, K.-F., Hung, J.-H., Wang, C.-Y., Tsai, Y.-B., Kondo, T., Nishimura, M., Moriya, S., Tanaka, T., Fujiki, T., Maeda, L., Muraki, H., Kuramoto, T., Sugiyama, K., and Sugawara, T. (2007), Nondestructive continuous physical property measurements of core samples recovered from Hole B, Taiwan Chelungpu-fault drilling project, J. Geophys. Res. 112, B07404, doi: 10.1029/2006JB004738.CrossRefGoogle Scholar
- Hirono, T., Ikehara, M., Otsuki, K., Mishima, T., Sakaguchi, M, Soh, W., Omori, M., Lin, W., Yeh, E.-C., Tanikawa, W., and Wang, C.-Y. (2006), Evidence of frictional melting within disk-shaped black materials discovered from the Taiwan Chelungpu fault system, Geophys. Res. Lett. 33, L19311, doi:10.1029/2006GL027329.CrossRefGoogle Scholar
- Ho, C.S., An Introduction to the Geology of Taiwan: Explanatory Text of the Geologic Map of Taiwan, 2 nd ed. (Central Geological Survey, Taipei, Taiwan, 1988).Google Scholar
- Hung, J.-H., Wu, Y.-H., Yeh, E.-C., Wu, J.-C., and TCDP Scientific Party (2007), Subsurface structure, physical properties, and fault zone characteristics in the scientific drill holes of Taiwan Chelungpu-Fault Drilling Project, Terr. Atmos. Ocean. Sci. 18(2), 271–293.CrossRefGoogle Scholar
- Johnson, K.M., Hsu, Y.J., Segall, P., and Yu, S.B. (2001), Fault geometry and slip distribution of the 1999 Chi-Chi, Taiwan Earthquake imaged from inversion of GPS data, Geophys. Res. Lett. 28, 2285–2288.CrossRefGoogle Scholar
- Kao, H. and Chen, W.-P. (2000), The Chi-Chi earthquake sequence: Active, out-of-sequence thrust faulting in Taiwan, Science 288, 2346–2349.CrossRefGoogle Scholar
- Kanamori, H. and Heaton, T.H., Microscopic and macroscopic physics of earthquakes. In Geocomplexity and Physics of Earthquakes (eds. Rundle, J.B., Turcotte, D.L., and Klein, W.) (American Geophysical Union, Washington, DC, 2000) pp. 147–163.Google Scholar
- Lachenbruch, A.H. and Sass, J.H. (1980), Heat flow and energetics of the San Andreas Fault zone, J. Geophys. Res. 85, 6185–6222.CrossRefGoogle Scholar
- Louis, L., Chen, T.-M.N., David, C., Robion, P., Wong, T.-F., and Song, S.-R. (2008), Anisotropy of magnetic susceptibility and P-wave velocity in core samples from the Taiwan Chelungpu-Fault Drilling Project, J. Struct. Geol., submitted.Google Scholar
- Lee, T.-C. and Delaney, P.T. (1987), Frictional heating and pore pressure rise due to fault slip, Geophys. J. R. Astron. Soc. 88, 569–591.Google Scholar
- Lockner, D., Naka, H., Tanaka, H., Ito, H., and Ikeda, R., Permeability and strength of core samples from the Nojima fault of the 1995 Kobe Earthquake. In Proc. the International Workshop on the Nojima Fault Core and Borehole Data Analysis, Tsukuba, Japan, 22–23 November 1999, Prelim. Rep. (eds Ito, H., Fujimoto, K., Tanaka, H., and Lockner, D.) (U.S. Geol. Surv. Open File Rep. 00-129, 1999) pp. 147–152.Google Scholar
- Lockner, D.A., Morrow, C., Song, S.-R., Tembe, S., and Wong, T.-F. (2005), Permeability of whole core samples of Chelungpu fault, Taiwan TCDP scientific drillhole, EOS Trans. AGU 86(52), Fall Meeting Suppl., Abstract T43D-04.Google Scholar
- Ma, K.-F., Brodsky, E.E., Mori, J., Ji, C., Song, T.-R.A., and Kanamori, H. (2003), Evidence for fault lubrication during the 1999 Chi-Chi, Taiwan, earthquake (M w 7.6), Geophys. Res. Lett. 30(5), doi:10.1029/2002GL015380.Google Scholar
- Mase, C.W. and Smith, L. (1987), Effects of frictional heating on the thermal, hydrologic, and mechanical response of a fault, J. Geophys. Res. 92, 6249–6272.CrossRefGoogle Scholar
- Morrow, C.A. and Lockner, D. (1994), Permeability differences between surface-derived and deep drillhole core samples, Geophys. Res. Lett. 21(19), 2151–2154.CrossRefGoogle Scholar
- Morrow, C., Lockner, D., Hickman, S., Rusanov, M., and Röckel, T. (1994), Effects of lithology and depth on the permeability of core samples from the Kola and KTB drill holes. J. Geophys. Res. 99(B4), 7263–7274.CrossRefGoogle Scholar
- Otsuki, K. and Monzawa, N. (2003), Fluidization and melting of fault gouge during seismic slip: Identification in the Nojima fault zone and implications for focal earthquake mechanisms, J. Geophys. Res. 108(B4), 2192, doi:10.1029/2001JB001711.CrossRefGoogle Scholar
- Otsuki, K., Uduki, T., Monzawa, N., and Tanaka, H. (2005), Clayey injection veins and pseudotachylyte from two boreholes penetrating the Chelungpu fault, Taiwan: Their implications for the contrastive seismic slip behaviors during the 1999 Chi-Chi earthquake, The Island Arc 14, 22–36.CrossRefGoogle Scholar
- Rice, J.R. (2006), Heating and weakening of faults during earthquake slip, J. Geophys. Res. 111, B05311, doi:10.1029/2005JB004006.CrossRefGoogle Scholar
- Seront, B., Wong, T.-F., Caine, J.S., Forster, C.B., Bruhn, R.L., and Fredrich, J. (1998), Laboratory characterization of hydrothermal properties of a seismogenic normal fault system, J. Struct. Geol. 20, 865–881.CrossRefGoogle Scholar
- Shin, T.-C. and Teng, T.-L. (2001), An overview of the 1999 Chi-Chi, Taiwan, earthquake, Bull. Seismol. Soc. Am. 91, 895–913.CrossRefGoogle Scholar
- Sibson, R.H. (1973), Interactions between temperature and fluid pressure during earthquake faulting — A mechanism for partial or total stress relief, Nature: Physical Science 243, 66–68.Google Scholar
- Sibson, R.H. (1977), Fault rocks and fault mechanisms, J. Geol. Soc. London 133, 191–231.CrossRefGoogle Scholar
- Song, S.-R., Kuo, L.-W., Yeh, E.-C., Wang, C.-Y., Hung, J.-H., and Ma, K.-F. (2007), Characteristics of the lithology, fault-related rocks and fault zone structures in TCDP Hole-A, Terr. Atmos. Ocean. Sci. 18(2), 243–269.CrossRefGoogle Scholar
- Suppe, J. and Wittke, J.H. (1977), Abnormal pore-fluid pressures in relation to stratigraphy and structure in the Active fold-and-thrust belt of northwestern Taiwan, Petroleum Geol. Taiwan 14, 11–24.Google Scholar
- Walsh, J.B. (1965), The effect of cracks on the compressibility of rocks, J. Geophys. Res. 70(2), 381–389.CrossRefGoogle Scholar
- Wang, W.-H., Chang, S.-H., and Chen, C.-H. (2001), Fault slip inferred from surface displacements during the 1999 Chi-Chi, Taiwan, earthquake, Bull. Seismol. Soc. Am. 91, 1167–1181.CrossRefGoogle Scholar
- Whipple, K.X. (1997), Open-channel flow of Bingham fluids: Applications in debris-flow research, J. Geol. 105, 243–262.CrossRefGoogle Scholar
- Wibberley, C.A.J. and Shimamoto, T. (2003), Internal structure and permeability of major strike-slip fault zones: The median tectonic line in Mie prefecture, Southwest Japan, J. Struct. Geol. 25, 59–78.CrossRefGoogle Scholar
- Wong, T.-F. and Zhu, W. (1999), Brittle faulting and permeability evolution: Hydromechanical measurement, microstructural observation, and network modeling. In Faults and Subsurface Fluid Flow in the Shallow Crust (eds. Haneberg, W.C., Mozley, P.S., Moore, J.C., and Goodwin L.B.) (AGU Geophysical Monograph Series 113) pp. 83–99.Google Scholar
- Yang, T.F., Walia, V., Lee, H.-F., Song, S.-R., and Wang, C.-Y. (2005), Compositions of on-site monitoring on dissolved gas of drilling mud flow and pore-gases of drilled cores of TCDP, EOS Trans. AGU 86(52), Fall Meeting Suppl., Abstract T51A-1315.Google Scholar
- Zhu, W. and Wong, T.-F. (1997), The transition from brittle faulting to cataclastic flow: Permeability evolution, J. Geophys. Res. 102, 3027–3041.CrossRefGoogle Scholar
- Zhu, W., Montesi, L., and Wong, T.-F., Effects of stress on the anisotropic development of permeability during mechanical compaction of porous sandstone. In Deformation Mechanisms, Rheology and Tectonics (eds. de Meer, S., Drury, M.R., de Bresser, J.H.P., and Pennock, G.M.) (Geological Society Special Publication 200, London 2002), pp. 119–136.Google Scholar