Advertisement

Prediction of Surface Roughness in Turning with Diamond Insert

  • Do Duc Trung
  • Nguyen Nhu Tung
  • Nguyen Hong Son
  • Tran Thi Hong
  • Nguyen Van Cuong
  • Vu Nhu Nguyet
  • Ngoc Pi VuEmail author
Conference paper
Part of the Lecture Notes in Networks and Systems book series (LNNS, volume 104)

Abstract

Prediction of the surface quality of a manufacturing process has a very important role. Therefore, in this paper, a study on the prediction of surface roughness in turning process with the use of diamond insert was presented. Based on the results of previous studies, a new surface roughness model was formulated. In the model, the effects of the depth of cut, the nose radius of the insert, the feed rate, and the characteristics of the workpiece material were taken into account. The surface roughness calculated from the model has been successfully verified by an experiment. Hence, this proposed model can be used to predict the surface roughness in turning processes using diamond inserts.

Keywords

Surface roughness Surface roughness model Turning process Diamond insert 

Notes

Acknowledgements

The work described in this paper was supported by Ha Noi University of Industry and Thai Nguyen University of Technology.

References

  1. 1.
    Abburi, N.R., Dixit, U.S.: A knowledge-based system for the prediction of surface roughness in turning process. Robot. Comput.-Integr. Manuf. 22, 363–372 (2006)CrossRefGoogle Scholar
  2. 2.
    Buldum, B., Şik, A., Akdagli, A., Biçer, M.B.: ANN surface roughness prediction of AZ91D magnesium alloys in the turning process. Mater. Test. 59, 916–920 (2017)CrossRefGoogle Scholar
  3. 3.
    Costes, J.-P.: A predictive surface profile model for turning based on spectral analysis. J. Mater. Process. Technol. 213(1), 94–100 (2013)CrossRefGoogle Scholar
  4. 4.
    Sidda Reddy, B., Suresh Kumar, J., Vijaya Kumar Reddy, K.: Prediction of surface roughness in turning using adaptive neuro-fuzzy inference system. Jordan J. Mech. Ind. Eng. 3(4), 252–259 (2009)Google Scholar
  5. 5.
    Boothroyd, G., Knight, W.A.: Fundamental of Machining and Machine Tool. Marcel Dekker, New York (1989)Google Scholar
  6. 6.
    Ståhl, J.-E., Schultheiss, F., Hägglund, S.: Analytical and experimental determination of the Ra surface roughness during turning. Procedia Eng. 19, 349–356 (2011)CrossRefGoogle Scholar
  7. 7.
    Groover, M.P.: Fundamentals of Modern Manufacturing. Prentice Hall, Upper Saddle River (1996)Google Scholar
  8. 8.
  9. 9.
  10. 10.
    Grzesik, W.: A revised model for predicting surface roughness in turning. Wear 194, 143–148 (1996)CrossRefGoogle Scholar
  11. 11.
    Zong, W.J., Huang, Y.H., Zhang, Y.L., Sun, T.: Conservation law of surface roughness in single point diamond turning. Int. J. Mach. Tools Manuf. 84, 58–63 (2014)CrossRefGoogle Scholar
  12. 12.
    Wang, H.X.: Research on establishing theoretical model of surface microtopography and experiment in ultraprecision turning (Ph.D. dissertation), Harbin Institute of Technology (2002)Google Scholar
  13. 13.
    Petros, G.: Petropoulos: the effect of feed rate and of tool nose radius on the roughness of oblique finish turned surface. Wear 23, 299–310 (1973)CrossRefGoogle Scholar
  14. 14.
  15. 15.

Copyright information

© Springer Nature Switzerland AG 2020

Authors and Affiliations

  • Do Duc Trung
    • 1
  • Nguyen Nhu Tung
    • 1
  • Nguyen Hong Son
    • 2
  • Tran Thi Hong
    • 3
  • Nguyen Van Cuong
    • 4
  • Vu Nhu Nguyet
    • 5
  • Ngoc Pi Vu
    • 5
    Email author
  1. 1.Faculty of Mechanical EngineeringHanoi University of IndustryHanoiVietnam
  2. 2.Center for Mechanical EngineeringHanoi University of IndustryHanoiVietnam
  3. 3.Center of Excellence for Automation and Precision Mechanical EngineeringNguyen Tat Thanh UniversityHo Chi Minh CityVietnam
  4. 4.Faculty of Mechanical EngineeringUniversity of Transport and CommunicationsHanoiVietnam
  5. 5.Faculty of Mechanical EngineeringThai Nguyen University of TechnologyThai NguyenVietnam

Personalised recommendations