Advertisement

Defect Analysis of Operating Hydro-Gasified Piping System

  • Min Ko HlaingEmail author
  • Phone Htet Kyaw
  • B. N. Maryn
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

Pipelines and hydraulic systems are widely used in all branches of engineering; their failure can lead to not only economic losses, but also result in serious environmental disasters. To assure the safety of a piping system, it is very important to carry on a routine inspection of pipelines to find out the defects or corrosions and the cause of defects as early as possible. Therefore, this article analyzes the causes of defects in pipelines and hydro-gasified systems in their manufacture, assembly and installation units, as well as in the service. A detailed classification of the fault lines and hydro-gasified systems is reported in this paper. The factors of reliability of a pipeline and communications units are determined. Further improvement of repairing a pipeline system technology is suggested. The research investigated the impact of piping configuration and its material on the system reliability in whole processing. The defects, which can be occurred when connecting pipelines with other elements during their manufacture, installation and in the service, are also presented in this article.

Keywords

Classification of defects Pipelines Hydro gasified system Deformation Flaw detection Leakage Connecting elements 

References

  1. 1.
    Shang HY (2016) A methodology for analysis of defective pipeline by introducing stress concentration factor into beam-pipe finite element formulation. Acta Scientiarum Tech 38(3):313–320.  https://doi.org/10.4025/actascitechnol.v38i3.27988MathSciNetCrossRefGoogle Scholar
  2. 2.
    Li S, Duan Q, Zhang H, Wang J (2017) Failure analysis of the floating pipeline with defect under flooding load. Eng Fail Anal 77:65–75.  https://doi.org/10.1016/j.engfailanal.2017.02.01CrossRefGoogle Scholar
  3. 3.
    Maryin BN (1998) The manufacture of pipelines of hydro-gas systems of aircraft. Moscow, pp 5–45Google Scholar
  4. 4.
    Yang H, Li H, Zhang ZY, Zhan M, Liu J, Li GJ (2012) Advances and trends on tube bending forming technologies. Chin J Aeronaut 25:1–12CrossRefGoogle Scholar
  5. 5.
    Kolykhalov DG, Sysoev OE, Ivanov IN (2016) Evaluation of the manufacturability of aircraft piping systems in the early design stages. Works MAI 90:26–30Google Scholar
  6. 6.
    Maryin BN, Feoktistov SI, Kolykhalov DG, Kuriniy VV, Ivanov IN (2016) Investigation of combined processes in the manufacture of aircraft parts. Sci Notes KnASU 2(26):34–41Google Scholar
  7. 7.
    Maryin BN (2008) Method of bending thin-walled pipes with filler. RU Patent 2337779 C2, 10 Nov 2008Google Scholar
  8. 8.
    Maryin BN (1990) Method of manufacturing of steeply curved thin-walled adapters. RU Patent, 1581411 A1Google Scholar
  9. 9.
    Sapozhnikov VM, Marin BN (1995) Intensification of technological processes of forming parts from pipes. Moscow, p 175Google Scholar
  10. 10.
    Gu RJ, Yang H, Zhan M, Li H, Wang GX (2005) Effect of mandrel on cross section quality of thin-walled tube numerical controlled bending. Trans Nonferrous Met Soc China 15:1264–1274Google Scholar
  11. 11.
    Li H, Yang H, Zhan M, Gu RJ (2007) The interactive effects of wrinkling and other defects in thin-walled tube NC bending process. J Mater Process Technol 187–188:502–507CrossRefGoogle Scholar
  12. 12.
    Paulsen F, Welo T (2003) An analytical model for prediction of tube ovalization in bending. In: Brucato V (ed) ESAFORM 2003: proceedings of the sixth ESAFORM conference on material forming, Salerno, Italy, pp 775–778Google Scholar
  13. 13.
    Lin Y, Yang H, Li H, Zhan M (2003) Influence of forming parameters on the wrinkling during the NC thin-walled tube bending process. Acta Aeronaut Astronau Sin 24:456–461Google Scholar
  14. 14.
    Maryin SB, Aung PW, Hlaing MK, Timoshinin MA (2018) Device for modern hardening and dispensing heated to a temperature for quenching the tubular billet of heat-treatable aluminum alloy. RU Patent, 2649102Google Scholar
  15. 15.
    Maryin BN (2007) Method of bending thin-walled pipes. RU Patent, 2322320 C2, 20 Apr 2007Google Scholar
  16. 16.
    Maryin BN (1993) Horn-shaped core for the manufacture of taps with flanges of pipe blanks. RU Patent, 1787617 A1Google Scholar
  17. 17.
    Murata M, Kuboki T, Takahashi K, Goodarzi M, Jin Y (2008) Effect of hardening exponent on tube bending. J Mater Process Technol 201:189–192CrossRefGoogle Scholar
  18. 18.
    Yang JB, Jeon BH, Oh SI (2001) The tube bending technology of a hydroforming process for an automotive part. J Mater Process Technol 111:175–181CrossRefGoogle Scholar

Copyright information

© Springer Nature Switzerland AG 2020

Authors and Affiliations

  • Min Ko Hlaing
    • 1
    Email author
  • Phone Htet Kyaw
    • 1
  • B. N. Maryn
    • 1
  1. 1.Komsomolsk-on-Amur State UniversityKomsomolsk-on-AmurRussia

Personalised recommendations