Advertisement

Idle Milling System Noise Level Dependency from Temperature Conditions of the Machine Working Area

  • Artem V. Rasshchupkin
  • Kirill P. PompeevEmail author
  • Viktor M. Medunetskiy
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

During experimental research, a deviation of milling system noise level measurement was detected in idle running mode during the period of equipment shift operation. A discrepancy of predicted parameters of predicted vibration activity of the milling system compared to the actual numbers during lowering of the spindle module operating frequencies range in the area of steady cutting. Based on the analysis of the obtained data and additional studies, dependency of system vibration and its noise level from the temperature conditions of the machine working area were identified. This dependency is proposed to be used to adjust the values of the predicted vibration of the milling setup by correlating temperature readings of the system with noise factor by taking into account the operating time of the equipment.

Keywords

Milling system run-out Noise peak Noise input Effective electric signal Cold source method 

References

  1. 1.
    Ershov DY (2013) Evaluation of the impact of technological errors of manufacture of the mechanical system on the vibration characteristics of a system during its operation. In: Radkevich MM, Evgrafov AN (eds) Modern machine industry: science and education: materials of the 3rd International research and training conference. Publishing house of the Polytechnic University, St. Petersburg, pp 709–717 (in Russian)Google Scholar
  2. 2.
    Korotkih MT (2014) Structural damping of cutting tools in intermittent machining. . In: Radkevich MM, Evgrafov AN (eds) Modern machine industry: science and education: materials of the 3rd International research and training conference. Publishing house of the Polytechnic University, St. Petersburg, pp 1140–1147 (in Russian)Google Scholar
  3. 3.
    Trofimova TV (1985) Physics studies. Higher School, Moscow, p 380 (in Russian)Google Scholar
  4. 4.
    Goryachev VJ, Gavrina OV, Chapchikov YK, Shatova YA (2013) Analysis of information and measurement system bias error based on the shaft run-out sensor shaft with the running magnetic field. Tech Sci 1, 46–57 (in Russian)Google Scholar
  5. 5.
    Agilent (2004) Noise Figure Measurement Accuracy – The Y-Factor Method. Application note 57–2, pp. 9-10Google Scholar
  6. 6.
    Vondran D (1999) Vector corrected noise figure measurements. Microwave J 22–38Google Scholar
  7. 7.
    Ivanov NI, Nikiforov AS (2000) Basics of vibroacoustics. Polytechnics, St. Petersburg, p 412 (in Russian)Google Scholar
  8. 8.
    Balykov IA, Chukarin AN, Evseev DZ (1996) Influence of cutting processes on milling machines noise. In: New in health and safety, and ecology: volume of conference reports, St. Petersburg, 14–16 Oct 1996, pp. 222–223 (in Russian)Google Scholar
  9. 9.
    Balykov IA (1996) On calculating the noise emitted by the workpiece when milling. Don State Technical University, Rostov on Don, Depositing in All-Union Institute of Scientific and Technical Information (VINITI), 16 Aug 96, no. 2685-B96 (in Russian)Google Scholar
  10. 10.
    Chukarin AN, Balykov IA (1996) Experimental studies of noise and vibration of milling machines. Don State Technical University, Rostov on Don, Depositing in All-Union Institute of Scientific and Technical Information (VINITI), 16 Aug 96, no. 2687-B96 (in Russian)Google Scholar
  11. 11.
    Zharkov IG (1986) Vibration during edge tool processing. Machine Industry, Leningrad, p 184 (in Russian)Google Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  • Artem V. Rasshchupkin
    • 1
  • Kirill P. Pompeev
    • 1
    Email author
  • Viktor M. Medunetskiy
    • 1
  1. 1.ITMO UniversitySaint-PetersburgRussia

Personalised recommendations