Advertisement

A Rolling Contact Joint Lower Extremity Exoskeleton Knee

  • Jonas Beil
  • Tamim Asfour
Conference paper
Part of the Advances in Intelligent Systems and Computing book series (AISC, volume 867)

Abstract

This paper presents the design, kinematics modeling and experimental evaluation of a rolling contact joint for usage as a knee joint in lower limb exoskeletons. The goal of the design is to increase wearability comfort by exploiting the migrating instantaneous joint center of rotation which is characteristic for rolling contact joints. Two 3D-printed parts with convex surfaces form the mechanism, which is coupled by two steel cables and driven by a linear actuator. This coupling allows rotations around all axis as well as predefined translations. We conducted a kinematic simulation to optimize the shape of the convex joint surfaces and to estimate the expected misalignment between the subject’s knee and exoskeleton joint. In our experimental evaluation we compared forces measured at the exoskeleton interface between subject and exoskeleton prototype with attached rolling contact or revolute joint. The results indicate a reduction of forces and therefore increased kinematic compatibility of the proposed joint design.

Keywords

Wearable robot Joint mechanism Exoskeleton knee joint 

Notes

Acknowledgment

This work has been supported by the German Federal Ministry of Education and Research (BMBF) under the project INOPRO (16SV7665).

References

  1. 1.
    CYBERDYNE Inc. HAL (2018). www.cyberdyne.jp
  2. 2.
    EKSO Bionics (2018). www.eksobionics.com
  3. 3.
    Wang, S., van der Kooij, H.: Modeling, design, and optimization of Mindwalker series elastic joint. In: IEEE International Conference on Rehabilitation Robotics (ICORR), pp. 1–8 (2013)Google Scholar
  4. 4.
    Hyon, S.-H.: et al.: Design of hybrid drive exoskeleton robot XoR2. In: IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pp. 4642–4648 (2013)Google Scholar
  5. 5.
    Wang, D., et al.: Adaptive knee joint exoskeleton based on biological geometries. IEEE/ASME Trans. Mechatron. 19(4), 1268–1278 (2014)CrossRefGoogle Scholar
  6. 6.
    Kim, K., et al.: Development of the exoskeleton knee rehabilitation robot using the linear actuator. Int. J. Precis. Eng. Manuf. 13(10), 1889–1895 (2012)CrossRefGoogle Scholar
  7. 7.
    Celebi, B., Yalcin, M., Patoglu, V.: AssistOn-Knee: a self-aligning knee exoskeleton. In: IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pp. 996–1002 (2013)Google Scholar
  8. 8.
    Choi, B., et al.: A self-aligning knee joint for walking assistance devices. In: International Conference of the Engineering in Medicine and Biology Society (EMBC), pp. 2222–2227 (2016)Google Scholar
  9. 9.
    Saccares, L., Sarakoglou, I., Tsagarakis, N.G.: iT-Knee: an exoskeleton with ideal torque transmission interface for ergonomic power augmentation. In: IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pp. 780–786 (2016)Google Scholar
  10. 10.
    Cai, D., et al.: Self-adjusting, isostatic exoskeleton for the human knee joint. In: Annual International Conference of the IEEE Engineering in Medicine and Biology Society, pp. 612–618 (2011)Google Scholar
  11. 11.
    Walker, P., Rovick, J., Robertson, D.: The effects of knee brace hinge design and placement on joint mechanics. J. Biomech. 21(11), 969–974 (1988)CrossRefGoogle Scholar
  12. 12.
    Wilson, D., et al.: The components of passive knee movement are coupled to flexion angle. J. Biomech. 33(4), 465–473 (2000)CrossRefGoogle Scholar
  13. 13.
    Neumann, D.A.: Kinesiology of the Musculoskeletal System: Foundations for Rehabilitation. Elsevier Health Sciences, London (2013)Google Scholar
  14. 14.
    Grood, E.S., Suntay, W.J.: A joint coordinate system for the clinical description of three-dimensional motions: application to the knee. J. Biomech. Eng. 105(2), 136–144 (1983)CrossRefGoogle Scholar
  15. 15.
    Lafortune, M., et al.: Three-dimensional kinematics of the human knee during walking. J. Biomech. 25(4), 347–357 (1992)CrossRefGoogle Scholar
  16. 16.
    Collins, C.L.: Kinematics of robot fingers with circular rolling contact joints. J. Rob. Syst. 20(6), 285–296 (2003)MathSciNetCrossRefGoogle Scholar
  17. 17.
    Kim, S.H., et al.: Force characteristics of rolling contact joint for compact structure. In: IEEE International Conference on Biomedical Robotics and Biomechatronics (BioRob), pp. 1207–1212 (2016)Google Scholar
  18. 18.
    Mun, J.H., Lee, D.-W.: Three-dimensional contact dynamic model of the human knee joint during walking. KSME Int. J. 18(2), 211–220 (2004)CrossRefGoogle Scholar
  19. 19.
    Montierth, J.R., Todd, R.H., Howell, L.L.: Analysis of elliptical rolling contact joints in compression. J. Mech. Des. 133(3), 031001 (2011)CrossRefGoogle Scholar
  20. 20.
    Nelson, T.G., et al.: Curved-folding-inspired deployable compliant rolling-contact element (D-CORE). Mech. Mach. Theory 96, 225–238 (2016)CrossRefGoogle Scholar
  21. 21.
    Kuntz, J.P.: Rolling link mechanisms. Delft University of Technology (1995)Google Scholar
  22. 22.
    Beil, J., Perner, G., Asfour, T.: Design and control of the lower limb exoskeleton KIT-EXO-1. In: IEEE International Conference on Rehabilitation Robotics (ICORR), pp. 119–124 (2015)Google Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  1. 1.High Performance Humanoid Technologies Lab (H²T), Institute for Anthropomatics and RoboticsKarlsruhe Institute of Technology (KIT)KarlsruheGermany

Personalised recommendations