Abstract
In this paper, the 2D surface model of single and multi-spark impacts on electrical discharge machining (EDM), with precise consideration of spark propagation, has been developed and simulated. Theoretical correlation between the input parameters, viz. discharge voltage (V): 30–110 V, discharge current (I): 5–75 A and spark on time (Ton): 10–200 µs, were preliminarily established, using the governing equations. The scope of the paper was to model the spark impact phenomenon, so as to determine the most influential factors which can be controlled to produce the required surface finish, for specific applications. Fine/finish machining is achievable at low discharge current, moderate discharge voltage and medium pulse on time, whereas coarse machining requires reverse conditions, preferably. Multi-spark analysis imparts insight into the possibilities in prediction and evaluation of material removal rate (MRR) and surface roughness (Ra) through further design considerations.
Keywords
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Singh, A., Ghosh, A.: A thermo-electric model of material removal during electric discharge machining. Int. J. Mach. Tools Manuf. 39(4), 669–682 (1999). https://doi.org/10.1016/S0890-6955(98)00047-9
DiBitonto, D.D., Eubank P.T., Patel, M.R., Barrufet, M.A.: Theoretical models of the electrical discharge machining process. I. A simple cathode erosion model. J. Appl. Phys. 66(9), 4095–4103 (1989). https://doi.org/10.1063/1.343994
Patel, M.R., Barrufet, M.A., Eubank, P.T., DiBitonto, D.D.: Theoretical models of the electrical discharge machining process. II. The anode erosion model. J. Appl. Phys. 66(9), 4104–4111 (1989). https://doi.org/10.1063/1.343995
Jilani, S.T., Pandey, P.C.: Analysis and modelling of EDM parameters. Precis. Eng. 4(4), 215–221 (1982). https://doi.org/10.1016/0141-6359(82)90011-3
Jilani, S.T., Pandey, P.C.: An analysis of surface erosion in electrical discharge machining. Wear 84(3), 275–284 (1983). https://doi.org/10.1016/0043-1648(83)90269-7
Van Dijck, F.S., Dutre, W.L.: Heat conduction model for the calculation of the volume of molten metal in electric discharges. J. Phys. D Appl. Phys. 7(6), 899 (1974). https://doi.org/10.1088/0022-3727/7/6/316
Das, S., Klotz, M., Klocke, F.: EDM simulation: finite element-based calculation of deformation, microstructure and residual stresses. J. Mater. Process. Technol. 142(2), 434–451 (2003). https://doi.org/10.1016/S0924-0136(03)00624-1
Joshi, S.N., Pande, S.S.: Development of an intelligent process model for EDM. Int. J. Adv. Manuf. Technol. 45(3–4), 300 (2009). https://doi.org/10.1007/s00170-009-1972-4
Beck, J.V.: Transient temperatures in a semi-infinite cylinder heated by a disk heat source. Int. J. Heat Mass Transf. 24(10), 1631–1640 (1981). https://doi.org/10.1016/0017-9310(81)90071-5
Beck, J.V.: Large time solutions for temperatures in a semi-infinite body with a disk heat source. Int. J. Heat Mass Transf. 24(1), 155–164 (1981). https://doi.org/10.1016/0017-9310(81)90104-6
Snoyes, R., Van Dijck, F.: Investigations of EDM operations by means of thermo mathematical models. Ann. CIRP 20(1), 35 (1971)
Snoeys, R.: Plasma channel diameter growth affects stock removal in EDM. Ann. CIRP 21, 39–40 (1972)
Acknowledgements
This work was carried out by the aid of research grant sanctioned from the Science and Engineering Research Board (SERB), DST, Govt. of India (Project Ref. No. ECR/2016/001929). Also, the authors are grateful to Mr. Anjan Karmakar for his significant contribution towards this initiative.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Philip, J.T., Kuriachen, B., Mathew, J. (2020). Numerical Modelling and Simulation of Single and Multi-spark Impacts in Electrical Discharge Machining. In: Shunmugam, M., Kanthababu, M. (eds) Advances in Simulation, Product Design and Development. Lecture Notes on Multidisciplinary Industrial Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-32-9487-5_39
Download citation
DOI: https://doi.org/10.1007/978-981-32-9487-5_39
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-32-9486-8
Online ISBN: 978-981-32-9487-5
eBook Packages: EngineeringEngineering (R0)