Abstract
Micro-EDM drilling becomes an important fabrication process for several different industrial applications. Micro-EDM drilling provides comparative advantages over conventional mechanical micro-drilling process owing to its capability of machining difficult-to-cut materials. This chapter provides a concise overview of micro-EDM drilling process. It presents working principle of the micro-EDM drilling as well as both operating and performance parameters along with some important applications. This chapter also covers micro-EDM drilling for difficult-to-cut materials such as steel alloys, Ti alloys and Ni alloys.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Yamane Y, Sekiya K (2004) An evaluation of difficulty in machining difficult-to-cut materials by using difficult-to-cut rating. J JSPE 70(3):407–411
Prakash V, Kumar P, Hussain M, Das AK, Chattopadhyaya S (2017) Micro-electrical discharge machining of difficult-to-machine materials: a review. Proc Inst Mech Eng, Part B: J Eng Manuf. https://doi.org/10.1177/0954405417718591
Ho KH, Newman ST (2003) State of the art electrical discharge machining (EDM). Int J Mach Tools Manuf 43(13):1287–1300
Pham DT, Dimov SS, Bigot S, Ivanov A, Popov K (2004) Micro-EDM—recent developments and research issues. J Mater Process Technol 149(1–3):50–57
Masuzawa T (2000) State of the art of micromachining. CIRP Ann Manuf Technol 49(2):473–488
Meek JM, Craggs JD (1978) Electrical breakdown of gases. Wiley, New York
Lee TH (1959) T-F theory of electron emission in high-current arcs. J Appl Phys 30(2):166–171
Kunieda M, Lauwers B, Rajurkar MP, Schumacher BM (2005) Advancing EDM through fundamental insight into the process. CIRP Ann Manuf Technol 54(2):64–87
Hockenberry TO, Williams EM (1967) Dynamic evolution of events accompanying the low-voltage discharges employed in EDM. IEEE Trans Ind Gen Appl 4:302–309
Kumar K, Rawal SK, Singh VP, Bala A (2018) Experimental study on diametric expansion and taper rate in EDM drilling for high aspect ratio micro holes in high strength materials. Mater Today: Proc 5(2, Part 2):7363–7372
Qian J, Yang F, Wang J, Lauwers B, Reynaerts D (2015) Material removal mechanism in low-energy micro-EDM process. CIRP Ann 64(1):225–228
Wong YS, Rahman M, Lim HS, Han H, Ravi N (2003) Investigation of micro-EDM material removal characteristics using single RC-pulse discharges. J Mater Process Technol 140(1–3):303–307
Singh A, Ghosh A (1999) A thermo-electric model of material removal during electric discharge machining. Int J Mach Tools Manuf 39(4):669–682
Muralikrishnan B, Stone J, Stoup J (2009) Diameter and form measurement of a micro-hole in a fuel injector nozzle with the NIST fiber probe. In: Proceedings of ASPE annual meeting, Monterey, Canada
Masuzawa T, Fujino M, Kobayashi K, Suzuki T, Kinoshita N (1985) Wire electro-discharge grinding for micro-machining. CIRP Ann Manuf Technol 34(1):431–434
Rowe W, Miyashita M, Koenig W (1989) Centreless grinding research and its application in advanced manufacturing technology. CIRP Ann Manuf Technol 38(2):617–625
Her M-G, Weng F-T (2001) Micro-hole machining of copper using the electro-discharge machining process with a tungsten carbide electrode compared with a copper electrode. Int J Adv Manuf Technol 17(10):715–719
Yan B, Huang FY, Chow HM, Tsai JY (1999) Micro-hole machining of carbide by electric discharge machining. J Mater Process Technol 87(1–3):139–145
Yu Z, Rajurkar KP, Shen H (2002) High aspect ratio and complex shaped blind micro holes by micro EDM. CIRP Ann Manuf Technol 51(1):359–362
Fu Y, Miyamoto T, Natsu W, Zhao W, Yu Z (2016) Study on influence of electrode material on hole drilling in micro-EDM. Procedia CIRP 42:516–520
Reynaerts D, Heeren PH, Brussel HV (1997) Microstructuring of silicon by electro-discharge machining (EDM)—part I: theory. Sens Actuators A: Phys 60(1–3):212–218
Ay M, Çaydaş U, Hasçalık A (2013) Optimization of micro-EDM drilling of Inconel 718 superalloy. Int J Adv Manuf Technol 66(5–8):1015–1023
Yu ZY, Zhang Y, Li J, Luan J, Zhao F, Guo D (2009) High aspect ratio micro-hole drilling aided with ultrasonic vibration and planetary movement of electrode by micro-EDM. CIRP Ann 58(1):213–216
Ferraris E, Castiglioni V, Ceyssens F, Annoni M, Lauwers B, Reynaerts D (2013) EDM drilling of ultra-high aspect ratio micro holes with insulated tools. CIRP Ann 62(1):191–194
Masuzawa T, Tsukamoto J, Fujino M (1989) Drilling of deep microholes by EDM. CIRP Ann Manuf Technol 38(1):195–198
Jahan MP, Wong YS, Rahman M (2010) A comparative experimental investigation of deep-hole micro-EDM drilling capability for cemented carbide (WC–Co) against austenitic stainless steel (SUS 304). Int J Adv Manuf Technol 46(9–12):1145–1160
Diver C, Atkinson J, Helml HJ, Li L (2004) Micro-EDM drilling of tapered holes for industrial applications. J Mater Process Technol 149(1):296–303
D’Urso G, Merla C (2014) Workpiece and electrode influence on micro-EDM drilling performance. Precis Eng 38(4):903–914
D’Urso G, Maccarini G, Ravasio C (2014) Process performance of micro-EDM drilling of stainless steel. Int J Adv Manuf Technol 72(9):1287–1298
Govindan P, Joshi SS (2010) Experimental characterization of material removal in dry electrical discharge drilling. Int J Mach Tools Manuf 50(5):431–443
Chen ST (2007) A high-efficiency approach for fabricating mass micro holes by batch micro EDM. J Micromech Microeng 17(10):1961
Chen ST (2008) Fabrication of high-density micro holes by upward batch micro EDM. J Micromech Microeng 18(8):085002
Chern GL, Chuang Y (2006) Study on vibration-EDM and mass punching of micro-holes. J Mater Process Technol 180(1–3):151–160
Liu HS, Yan BH, Huang FY, Qiu KH (2005) A study on the characterization of high nickel alloy micro-holes using micro-EDM and their applications. J Mater Process Technol 169(3):418–426
Imran M, Mativenga PT, Gholinia A, Withers PJ (2015) Assessment of surface integrity of Ni superalloy after electrical-discharge, laser and mechanical micro-drilling processes. Int J Adv Manuf Technol 79(5–8):1303–1311
Hung JC, Wu WC, Yan BH, Huang FY, Wu KL (2007) Fabrication of a micro-tool in micro-EDM combined with co-deposited Ni–SiC composites for micro-hole machining. J Micromech Microeng 17(4):763
Perveen A, Jahan MP (2018) Application of Box Behnken design to model crater size generated during micro-EDM of NI-X alloy. Int J Mech Eng Rob Res 7(3):229–234
Perveen A, Jahan MP (2018) Comparative micro-EDM studies on Ni based X-alloy using coated and uncoated tools. Mater Sci Forum 911:13–19
Bhosle RB, Sharma SB (2017) Multi-performance optimization of micro-EDM drilling process of Inconel 600 alloy. Mater Today: Proc 4(2, Part A):1988–1997
Meena VK, Azad MS (2012) Grey relational analysis of micro-EDM machining of Ti-6Al-4V alloy. Mater Manuf Process 27(9):973–977
Li Y, Yu W, Xu J, Yu H (2016) A comparative investigation of micro-EDM drilling capability for Ti-6Al-4V alloy against austenitic stainless steel SUS 316. In: IEEE international conference on mechatronics and automation, Harbin, China, 7–10 Aug 2016
Plaza S, Sanchez JA, Perez E, Gil R, Izquierdo B, Ortega N, Pombo I (2014) Experimental study on micro EDM-drilling of Ti6Al4V using helical electrode. Precis Eng 38(4):821–827
Kibria G, Sarkar BR, Pradhan BB, Bhattacharyya B (2010) Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti-6Al-4V alloy. Int J Adv Manuf Technol 48(5–8):557–570
Jahan MP, Wong YS, Rahman M (2012) Experimental investigations into the influence of major operating parameters during micro-electro discharge drilling of cemented carbide. Mach Sci Technol 16(1):131–156
Wansheng Z, Zhenlong W, Shichun D, Guanxin C, Hongyu W (2002) Ultrasonic and electric discharge machining to deep and small hole on titanium alloy. J Mater Process Technol 120(1):101–106
Perveen A, Jahan MP, Zhumagulov S (2018) Statistical modelling and optimization of micro electro discharge machining of Ti Alloy. Mater Today: Proc 5(2):4803–4810
Tiwary AP, Pradhan BB, Bhattacharyya B (2015) Study on the influence of micro-EDM process parameters during machining of Ti–6Al–4V superalloy. Int J Adv Manuf Technol 76(1):151–160
Alavi F, Jahan MP (2017) Optimization of process parameters in micro-EDM of Ti-6Al-4V based on full factorial design. Int J Adv Manuf Technol 92(1–4):167–187
Krishnaraj V (2016) Optimization of process parameters in micro-EDM of Ti-6Al-4V Alloy. J Manuf Sci Prod 16(1):41–49
Jahan MP, Rahman M, Wong YS (2011) A review on the conventional and micro-electrodischarge machining of tungsten carbide. Int J Mach Tools Manuf 51(12):837–858
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Singapore Pte Ltd.
About this chapter
Cite this chapter
Oliaei, S.N.B., Jahan, M.P., Perveen, A. (2019). Micro-EDM Drilling. In: Kibria, G., Jahan, M., Bhattacharyya, B. (eds) Micro-electrical Discharge Machining Processes. Materials Forming, Machining and Tribology. Springer, Singapore. https://doi.org/10.1007/978-981-13-3074-2_1
Download citation
DOI: https://doi.org/10.1007/978-981-13-3074-2_1
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-13-3073-5
Online ISBN: 978-981-13-3074-2
eBook Packages: EngineeringEngineering (R0)