Abstract
Flat peripheral grinding of 20 Kh steel, samples are studied. The authors propose a method of determining optimal conditions for grinding sample surfaces that guarantees obtaining the predefined quality requirements to the machined surface (surface roughness parameter Ra, the absence of grinding burns), while ensuring the maximum efficiency of the process. The mathematical models of the cutting force components reduced to the width of the sample, grinding ratio, and roughness of the machined surface (Ra parameter) are obtained by the method of full factorial experiment of the 24 type, where 4 is the number of factors. The input factors (grinding wheel hardness, depth of grinding, table feed speed, and run reduced to the width of the machined surface) are considered as the optimization parameters of the grinding process. The mathematical models of the output factors are used to limit the range of allowable values of the optimization parameters. The resulted efficiency is an objective function. The optimization of parameters in the range of allowable values is carried out with the view of ensuring maximum efficiency of the process.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Dal’skiy AM, Kosilova AG, Meshcheriakov RK, Suslov AG (eds) (2001) Spravochnik tekhnologa-mashinostroitelia (Reference technologist-mechanical engineer). V 2 vol. 1, Mashinostroenie-1 Publication, Moscow
Nosenko VA, Tyshkevich VN, Orlov SV et al (2014) Ploskoe shlifovanie tortsov kolets krupnogabaritnykh podshipnikov s trebuemym kachestvom poverkhnosti (Flat grinding of big bearing races end with the demanded quality of a surface). Vestnik Iuzhno-Ural’skogo gosudar-stvennogo universiteta. Seriia: Mashinostroenie 14(4):67–78
Nosenko VA, Tyshkevich VN, Orlov SV et al (2015) Optimal’nye usloviia shlifovaniia tortsevykh poverkhnostei kolets krupnogabaritnykh podshipnikov (Determination of optimal grinding conditions of end sur-faces of races of big bearings). Vestn mashinostroeniia 4:60–66
Nosenko VA, Tyshkevich VN, Orlov SV (2015) Obespechenie trebuemogo kachestva tortsovyih pover-hnostey kolets podshipnikov shlifovaniem (Providing the required quality of end surfaces bearing races during grinding). Sborka v mashinostroenii, priborostroenii 3:31–35
Nosenko VA, Tyshkevich VN, Orlov SV et al (2016) Vybor optimal’nyh uslovij ploskogo shlifovanija stal’nyh zagotovok (The determination of optimal conditions for flat grinding of steel work-pieces). Izvestiya vyisshih uchebnyih zavedeniy. Mashinostroenie 6:73–81
Nosenko VA, Tyshkevich VN, Sarazov AV (2017) Optimization of conditions for non-rigid workpieces flat grinding by elastic deformations controlling. Proc Eng 206:1173–1178. https://doi.org/10.1016/j.proeng.2017.10.613
IaI S, Kazimirov D (2006) Strategiia ploskogo shlifovaniia detalei peremennoi zhestkosti (The strategy of the flat grinding to details of a variable rigidity). Metalloobrabotka 1:2–7
YaI S, Nguen VK (2016) Tekhnologicheskie rezervy povysheniya kachestva shlifovaniya plastin iz bystrorezhushchey stali povyshennoy proizvoditel’nosti (Technological Reserves of Improving Grinding Quality of High Speed Steel Plates with Improved Productivity). Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie 5(674):59–73
Dal’skiy AM, Kosilova AG, Meshcheriakov RK, Suslov AG (eds) (2003) Reference technologist-mechanical engineer (Reference technologist-mechanical engineer). V 2 vol. 2, Mashinostroenie-1 Publishing, Moscow
Soler Ya I, Nguen VK, Hoang NA (2017) Prognozirovanie rezhimov chistovogo shlifovaniya bystrorezhushchikh plastin peremennoy podatlivosti pri mnogoparametricheskoy optimizatsii sherokhovatosti (Predicting finishing grinding conditions for high-speed cutting plates of variable compliance using multiparametric optimization of roughness). Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie 4(685):35–46
Korotkov BI, Korotkov SB, Tyshkevich VN et al (2007) Issledovanie protsessov shlifovaniia vnutrennikh i naruzhnykh konusov detalei klassa kolets (Research of processes of grinding the inner and outer parts of the cones class rings). VolgSTU Publishing, Volgograd
Nosenko VA, Tyshkevich VN, Orlov SV et al (2010) The determination of axial displacements during bearing end face grinding. J Mach Manuf Reliab 39(2):157–160
Nosenko VA, Tyshkevich VN, Orlov SV et al (2015) Vliianie osevyih deformatsiy na otklonenie ot ploskostnosti tortsovoy poverhnosti koltsa podshipnika pri shlifovanii (Influence of axial deformations on flatness deviation of end surface of the bearing race during grinding). Izvestiya vyisshih uchebnyih zavedeniy. Mashinostroenie 9:68–74
Tyshkevich VN, Nosenko VA, Sarazov AV (2017) Povyshenie effektivnosti ploskogo shlifovaniya tortsov prizmaticheskikh zagotovok maloy zhestkosti (Increase in efficiency of flat grinding of end surfaces of prismatic workpieces of small rigidity). Izvestiya VolgGTU. Ser. Progressivnye tekhnologii v mashinostroenii 9(204):105–108
Nosenko VA, Tyshkevich VN, Orlov SV et al (2016) Modelirovanie osevykh uprugikh deformatsiy pri shlifovanii tortsov kolets krupnogabaritnykh podshipnikov (Modelling of axial elastic deformations at grinding end faces of big bearings rings). Fundamental’nye i prikladnye problemy tekhniki i tekhnologii 5(319):41–48
Nosenko VA, Tyshkevich VN, Orlov SV et al (2016) Obespechenie dopuska ploskostnosti pri shlifovanii tortsov nezhestkikh kolets podshipnikov (Providing flatness tolerance for grinding the ends of non-rigid bearing rings). Mekhaniki XXI veku 15:173–179
Nosenko VA, Tyshkevich VN, Orlov SV et al (2017) Upravlenie osevymi uprugimi deformatsiyami nezhestkikh kolets podshipnikov pri ploskom shlifovanii tortsov (The control of axial elastic deformations of non-rigid bearing rings when flat grinding end surfaces). Izvestiya vyisshih uchebnyih zavedeniy. Mashinostroenie 1(682):63–70
Nosenko VA, Tyshkevich VN, Sarazov AV et al (2017) Algoritm vybora optimal’nykh rezhimov ploskogo shlifovaniya nezhestkikh zagotovok (The algorithm of optimal conditions determination for flat grinding of non-rigid workpieces). Sistemy. Metody. Tekhnologii 1(33):34–38
Nosenko VA, Tyshkevich VN, Sarazov AV (2017) Povyshenie effektivnosti ploskogo shlifovaniya nezhestkikh zagotovok putem upravleniya uprugimi deformatsiyami (Increasing efficiency of flat grinding of non-rigid workpieces by control of elastic deformations). Vestnik Rybinskogo gos. aviatsionnoy tekhnologicheskoy akademii 2(41):342–348
Nosenko VA, Tyshkevich VN, Orlov SV et al (2016) Upravlenie uprugimi deformatsiyami nezhestkikh podshipnikovykh kolets pri zakreplenii i mekhanicheskoy obrabotke (The control elastic deformations of non-rigid bearing rings when fixing and machining). J Mod Technol Collect Sci Pap 3:53–62
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this paper
Cite this paper
Tyshkevich, V.N., Nosenko, V.A., Sarazov, A.V. (2019). Determination of Optimal Conditions for Flat Grinding of 20 Kh Steel Workpieces. In: Radionov, A., Kravchenko, O., Guzeev, V., Rozhdestvenskiy, Y. (eds) Proceedings of the 4th International Conference on Industrial Engineering. ICIE 2018. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-319-95630-5_134
Download citation
DOI: https://doi.org/10.1007/978-3-319-95630-5_134
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-95629-9
Online ISBN: 978-3-319-95630-5
eBook Packages: EngineeringEngineering (R0)