Abstract
The typical examples of mechanical machining are ultrasonic machining and water jet machining. Mechanical abrasion is the main mechanism for the material removal in case of ultrasonic machining whereas in case of water jet machining it is the cutting action of the fluid jet. The medium under which the machining takes place is abrasive slurry in case of ultrasonic machining while the water jet machining is performed in the presence of fluid. The present chapter describes the different mechanical nontraditional processes.
Keywords
- Ultrasonic Machining
- Abrasive Slurry
- AWJM Process
- Abrasive Particles
- Abrasive Water Jet Machining (AWJM)
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
V.I. Babitsky, A.V. Mitrofanov, V.V. Silverschmidt, Ultrasonically assisted turning of aviation materials: simulations and experimental study. Ultrasonics 42, 81–86 (2004)
L.A. Balamuth, Ultrasonic assistance to conventional metal removal. Ultrasonics 4, 125–130 (1966)
M.M. Barash, D. Watanapongse, On the effect of ambient pressure on the rate of material removal in ultrasonic machining. Int. J. Mech. Sci. 12, 775–779 (1970)
G.F. Benedict, Non-Traditional Manufacturing Processes (Marcel Dekker Inc., New York, 1987), pp. 67–86
T.J. Bulat, Micro-Sonics in Industry: Ultrasonic Cleaning, Bendix and Life Supports Division Publication, USA, 120.10.153: 13 (1974)
S. Chang, G.M. Bone, Burr size reduction in drilling by ultrasonic assistance. Robot. Comput. Integr. Manuf. 120, 442–450 (2005)
F.L. Chen, E. Siores, The effect of cutting jet variation on striation formation in abrasive water jet cutting. Int. J. Mach. Tools Manuf 41(10), 1479–1486 (2001)
G.S. Choi, G.H. Choi, Process analysis and monitoring in abrasive water jet machining of alumina ceramics. Int. J. Mach. Tools Manuf. 37(3), 295–307 (1997)
N.H. Cook, Manufacturing Analysis (Addison-Wesley, New York, 1966), pp. 133–148
W.L. Cong, Z.J. Pei, C. Treadwell, Preliminary study on rotary ultrasonic machining of CFRP/Ti stacks. Ultrasonics 54(6), 1594–1602 (2014)
J. Deng, T. Lee, Ultrasonic machining of alumina based ceramic composites. J. Eur. Ceram. Soc. 22(8), 1235–1241 (2002)
F.T. Farago, Abrasives methods engineering. Indus. Press 2, 480–481 (1980)
F. Farzin-Nia, T. Sterrett, Effect of machining on fracture toughness of corundum. J. Mater. Sci. 25(5), 2527–2531 (1990)
J.R. Frederick, Ultrasonic Engineering (Wiley, New York, 1965), pp. 32–45
G. Fowler, I.R. Pashby, P.H. Shipway, The effect of particle hardness and shape when abrasive water jet milling titanium alloy Ti6Al4V. Wear 266(7), 613–620 (2009)
R. Gilmore, Ultrasonic machining and orbital abrasion techniques. SME Technical Paper (series) AIR, NM89–419: 1–20 ((1989
D. Goetze, Effect of vibration amplitude, frequency, and composition of the abrasive slurry on the rate of ultrasonic machining in Ketos Tool Steel. J. Acoust. Soc. America 28(6), 1033–1045 (1956)
K.F. Graff, Macrosonics in industry: ultrasonic machining. Ultrasonics 13, 103–109 (1975)
A. Gupta, Performance optimization of abrasive fluid jet for completion and stimulation of oil and gas wells. J. Energy Res. Technol. 134(2), 021001 (2012)
M. Hashish, A modeling study of metal cutting with abrasive waterjets. J. Eng. Mater. Technol. 106(1), 88–100 (1984)
M. Hashish, Visualization of the abrasive-waterjet cutting process. Exp. Mech. 28(2),159–169 15 (1988)
M. Hashish, A model for abrasive-waterjet (AWJ) machining. J. Eng. Mater. Technol. 111(2), 154–162 16 (1989a)
M. Hashish, Pressure effects in abrasive-waterjet (AWJ) machining. J. Eng. Mater. Technol. 111(3), 221–228 (1989b)
M. Hashish, Characteristics of surfaces machined with abrasive-waterjets. J. Eng. Mater. Technol. 113(3), 354–362 (1991a)
M. Hashish, Optimization factors in abrasive-waterjet machining. J. Eng. İnd. 113(1), 29–37 (1991b)
M. Hashish, Effect of abrasive waterjet parameters on volume removal trends in turning. J. Eng. İnd. 117, 475 (1995)
L.M. Hlaváč, I.M. Hlaváčová, L. Gembalová, J. Kaličinský, S. Fabian, J. Měšťánek, V. Mádr, Experimental method for the investigation of the abrasive water jet cutting quality. J. Mater. Process. Technol. 209(20), 6190–6195 (2009)
P. Hu, J.M. Zhang, Z.J. Pei, C. Treadwell, Modeling of material removal rate in rotary ultrasonic machining: designed experiments. J. Mater. Process. Technol. 129, 339–344 (2002)
K. Ishikawa, H. Suwabe, T. Nishide, M. Uneda, A study on combined vibration drilling by ultrasonic and low-frequency vibrations for hard and brittle materials. Prec. Eng. 22, 197–206 (1998)
Y. Jiao, W.J. Liu, Z.J. Pei, X.J. Xin, C. Treadwell, Study on edge chipping in rotary ultrasonic machining of ceramics: an integration of designed experiments and finite element method analysis. J. Manuf. Sci. Eng. 127(4), 752–758 (2005)
E. Kai, M. Takahira, Micro ultrasonic machining by application of work-piece vibration. CIRP Ann. 48(1), 131–134 (1999)
G.S. Kainth, A. Nandy, K. Singh, On the mechanisms of material removal in ultrasonic machining. Int. J. Mach. Tool Des. 19, 33–41 (1979)
F. Kartal, H. Gökkaya, Aşındırıcı Su Jeti ile Tornalama Deney Düzeneği Tasarımı. In International Iron & Steel Symposium Karabük, Türkiye (2012)
F. Kartal, M.H. Çetin, H. Gökkaya, Z. Yerlikaya, Optimization of abrasive water jet turning parameters for machining of low density polyethylene material based on experimental design method. Int. Polym. Proc. 29(4), 535–544 (2014)
V.F. Kazantsev, The relationship between output and machining conditions in ultrasonic machining. Mach. Tool. 34, 14–17 (1963)
V.F. Kazantsev, Improving the output and accuracy of ultrasonic machining. Mach. Tool. 37(4), 33–39 (1966)
D.C. Kennedy, R.J. Grieve, Ultrasonic machining—a review. Prod. Eng. 54(9), 481–486 (1975)
L. Koops, Investigation into the influence of the wear of abrasive powder on the technological indices of ultrasonic machining. Ann. CIRP 13(3), 151–157 (1964)
D. Kremer, The state of the art of ultrasonic machining. Ann. CIRP 30, 107–115 (1981)
J.B. Kohals, Ultrasonic manufacturing process-ultrasonic machining and ultrasonic impact grinding (USIG). The Carbide and Tool J. 16(5), 12–15 (1984)
M. Komaraiah, P.N. Reddy, A study on the influence of workpiece properties in ultrasonic machining. Int. J. Mach. Tools Manuf. 33, 495–505 (1993a)
M. Komariah, P.N. Reddy, Relative performance of tool materials in ultrasonic machining. Wear 161(1–2), 1–10 (1993b)
R. Kovacevic, A new sensing system to monitor abrasive waterjet nozzle wear. J. Mater. Process. Technol. 28(1–2), 117–125 (1991)
R. Kovacevic, M. Hashish, R. Mohan, M. Ramulu, T.J. Kim, E.S. Geskin, State of the art of research and development in abrasive waterjet machining. J. Manuf. Sci. Eng. 119(4B), 776–785 (1997)
J. Kumar, J.S. Khamba, An experimental study on ultrasonic machining of pure titanium using designed experiments. J. Brazilian Soc. Mech. Sci. Eng. 30(3), 231–238 (2008)
J. Kumar, J.S. Khamba, S.K. Mohapatra, An investigation into the machining characteristics of titanium using ultrasonic machining. Int. J. Mach. Mach. Mater. 3(1–2), 143–161 (2008)
A. Kumar, V. Kumar, J. Kumar, Prediction of surface roughness in wire electric discharge machining (WEDM) process based on response surface methodology. Int. J. Eng. Technol. 2(4), 708–712 (2012)
A. Kumar, V. Kumar, J. Kumar, Investigation of machining parameters and surface integrity in wire electric discharge machining (WEDM) of pure titanium. In Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture (2013a) https://doi.org/10.1177/0954405413479791
A. Kumar, V. Kumar, J. Kumar, Multi-response optimization of process parameters based on response surface methodology for pure titanium using WEDM process. In International Journal of Advanced Manufacturing Technology (2013b) https://doi.org/10.1007/s00170-013-4861-9
H. Kumehara, Characteristics of threaded joints in ultrasonic vibrating system. Bull. JSME 27(223), 117–123 (1984)
S. Kunaporn, M. Ramulu, M. Hashish, Mathematical modeling of ultra-high-pressure waterjet peening. J. Eng. Mater. Technol. 127(2), 186–191 (2005)
Z.C. Li, Wu-L Cai, Z.J. Pei, C. Treadwell, Edge chipping reduction in rotary ultrasonic machining of ceramics: finite element analysis and experimental verification. Int. J. Mach. Tools Manuf. 46(12–13), 1469–1477 (2005)
W.Y. Li, J. Wang, Y.M. Ali, An experimental study of radial-mode abrasive waterjet turning of steels. Mater. Sci. Orum 697, 166–170 (2012)
Z. Liang, Y. Wu, X. Wang, W. Zhao, A new two dimensional ultrasonic assisted grinding (UAG) method and its fundamental performance in monocrystal silicon machining. Int. J. Mach. Tools Manuf. 50, 728–736 (2010)
H. Liu, J. Wang, N. Kelson, R.J. Brown, A study of abrasive waterjet characteristics by CFD simulation. J. Mater. Process. Technol. 153, 488–493 (2004)
T.C. Lee, C.W. Chan, Mechanism of the ultrasonic machining of ceramic composites. J. Mater. Process. Technol. 71, 195–201 (1997)
C. Ma, R.T. Deam, A correlation for predicting the kerf profile from abrasive water jet cutting. Exp. Thermal Fluid Sci. 30(4), 337–343 (2006)
M.A. Majeed, L. Vijayaraghvan, S.K. Malhotra, R. KrishnaMurthy, Ultrasonic machining of Al2O3/LaPO4 composites. Int. J. Mach. Tools Manuf. 48, 40–46 (2008)
A.I. Markov, Kinematics of the dimensional ultrasonic machining method. Mach. Tool. 30(10), 28–31 (1959)
A.I. Markov, Ultrasonic drilling and milling of hard non-metallic materials with diamond tools. Mach. Tool. 48(9), 45–47 (1977)
L.G. Merkulov, Design of ultrasonic concentrations. Akusticheskiy Zhurnal 3, 246–255 (1957)
G.E. Miller, Special theory of ultrasonic machining. J. Appl. Phys. 28(2), 149–156 (1957)
A.W. Momber, R. Kovacevic, Principles of abrasive water jet machining (Springer Science & Business Media, USA, 2012)
D. Moore, Ultrasonic impact grinding. In Proceedings Non-Traditional Machining Conference, Cinicinnati, OH, USA, 1985, pp. 137–139
E.V. Nair, A. Ghosh, A fundamental approach to the study of mechanics of ultrasonic machining. Int. J. Prod. Res. 23, 731–753 (1985)
M. Nanduri, D.G. Taggart, T.J. Kim, A study of nozzle wear in abrasive entrained water jetting environment. J. Tribol. 122(2), 465–471 (2000)
M. Nanduri, D.G. Taggart, T.J. Kim, The effects of system and geometric parameters on abrasive water jet nozzle wear. Int. J. Mach. Tools Manuf. 42(5), 615–623 (2002)
E.A. Neppiras, Ultrasonic machining and forming. Ultrasonics. 2(4), 167–173 (1964)
G. Nishimura, Ultrasonic machining—Part I. J. Fract. Eng. Tokyo University 24(3), 65–100 (1954)
E.A. Neppiras, Ultrasonic machining-II. Operating conditions and performance of ultrasonic drills. Philips Technol. Rev. 18(12), 368–379 (1957)
P.C. Pandey, H.S. Shan, Modern Machining Processes (Tata McGraw-Hill, New Delhi, 1980), pp. 7–38
Z.J. Pei, N. Khanna, P.M. Ferreira, Rotary ultrasonic machining of structural ceramics—a review. Ceram. Eng. Sci. Proc. 16(1), 259–278 (1995)
Z.J. Pei, P.M. Ferreira, An experimental investigation of rotary ultrasonic face milling. Int. J. Mach. Tools Manuf. 39(8), 1327–1344 (1999)
E.W. Pentland, J.A. Ektermanis, Improving ultrasonic machining rates—some feasibility studies. J. Eng. Indus. Trans. ASME 87, 39–46 (1965)
D. Prabhakar, M. Haselkorn, An experimental investigation of material removal rates in rotary ultrasonic machining. Trans. NAMRI = SME, 20, 211–218 (1992)
M. Ramulu, D. Arola, Water jet and abrasive water jet cutting of unidirectional graphite/epoxy composite. Composites 24(4), 299–308 (1993)
M. Ramulu, Ultrasonic machining effects on the surface finish and strength of silicon carbide ceramics. Int. J. Manuf. Technol. Manag. 7(2/3/4), 107–125 (2005)
V. Riddie, Cavitation erosion—a survey of the literature 1940–1970. Wear 23, 133–137 (1973)
L.D. Rozenberg, V.F. Kazantsev, L.O. Makarov, Ultrasonic Cutting (Consultant Bureau, New York, 1964), pp. 97–102
L.D. Rozenberg, Physical Principles of Ultrasonic Technology, 1–2 (Plenum Press, New York, 1973), pp. 20–53
J. Saha, A. Bhattacharya, P.K. Mishra, Estimation of material removal rates in USM process—a theoretical and experimental study. In Proceedings 27th International Matador Conference Manchester, England, 31–46 (1988)
A. Sharma, S. Mishiro, K. Suzuki, T. Imai, A new longitudinal mode ultrasonic transducer with an eccentric horn for micro machining. Key Eng. Mater. 238–239, 147–152 (2003)
M.C. Shaw, Ultrasonic grinding. Ann. CIRP 5, 25–53 (1956)
R. Snoyes, Non-conventional machining techniques: the state of art. Adv. Non-Trad. Mach. ASME, 1–20 (1986)
V. Soundrajan, V. Radhakrishnan, An experimental investigation on the basic mechanisms involved in the ultrasonic machining. Int. J. Mach. Tool Des. Res. 26(3), 307–321 (1986)
P.S. Sreejith, B.K.A. Ngoi, Material removal mechanisms in precision machining of new materials. Int. J. Mach. Tools Manuf 41, 1831–1843 (2001)
T.B. Thoe, D.K. Aspinwall, M.L.H. Wise, The effect of operating parameters on ultrasonic contour machining. In Proceedings 12th Annual Conference of the Irish Manufacturing Committee, Cork, Ireland, Sep., 1995, pp. 305–312 (1995)
T.B. Thoe, D.K. Aspinwall, N. Killey, Combined ultrasonic and electrical discharge machining of ceramic coated nickel alloy. J. Mater. Process. Technol, 92, 323–328 (1999)
C. Treadwell, P. Hu, J.M. Zhang, Modeling of material removal rate in rotary ultrasonic machining: designed experiments. J. Mater. Process. Technol. 129(1–3), 339–344 (2002)
G. Vikram, N.R. Babu, Modelling and analysis of abrasive water jet cut surface topography. Int. J. Mach. Tools Manuf. 42(12), 1345–1354 (2002)
Z.Y. Wang, K.P. Rajurkar, Dynamic analysis of ultrasonic machining process. In Proceedings of the 1995 ASME International Mechanical Engineering Congress and Exposition, Part I: 87–97 (1995)
J. Wang, Abrasive waterjet machining of polymer matrix composites—cutting performance, erosive process and predictive models. Int. J. Adv. Manuf. Technol. 15(10), 757–768 (1999)
Z. Wansheng, W. Zhenlong, D. Shichun, C. Guanxin, W. Hongyu, Ultrasonic and electric discharge machining to deep and small hole on titanium alloy. J. Mater. Process. Technol, 120(1–3), 101–106 (2002)
E.J. Weller, Non-traditional machining processes. Society of Manufacturing Engineers, 15–71 (1984)
G.W. Willard, Ultrasonically induced cavitation. J. Acoust. Soc. America 25, 669 (1953)
G. Ya, H.W. Quin, S.C. Yang, Analysis of rotary ultrasonic machining mechanism. J. Mater. Process. Technol. 129(1–3), 182–185 (2002)
K. Yanaida, A. Ohashi, Flow characteristics of water jets. In Second International Symposium on Jet Cutting Technology, A2, Cranfield, pp. 19–32 (1974)
K. Yanaida, A. Ohashi, Flow characteristics of water jets in air. In Fifth International Symposium on Jet Cutting Technology, A3, Hannover, pp. 33–43 (1980)
H.A. Youssef, H.A. El-Hofy, Machining technology: machine tools and operations. CRC Press (2008)
W.M. Zeng, Z.C. Li, Z.J. Pei, C. Treadwell, Experimental observation of tool wear in rotary ultrasonic machining of advanced ceramics. Int. J. Mach. Tools Manuf. 45, 1468–1473 (2005)
M. Zvoncan, M. Beno, M. Kovac, J. Peterka, Cross section of machined layer for rotary ultrasonic machining with a hollow drill. Manuf. Indus. Eng. 11(3), 11–13 (2012)
Z.W. Zhong, Z.Z. Han, Turning of glass with abrasive waterjet. Mater. Manuf. Proc. 17(3), 339–349 (2002)
I. Zohourkari, M. Zohoor, Mathematical modeling of abrasive waterjet turning of ductile materials. In ASME 2010 10th Biennial Conference on Engineering Systems Design and Analysis (American Society of Mechanical Engineers, 2010), pp. 825–830
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2018 Springer International Publishing AG, part of Springer Nature
About this chapter
Cite this chapter
Kumar, K., Zindani, D., Davim, J.P. (2018). Mechanical Machining. In: Advanced Machining and Manufacturing Processes. Materials Forming, Machining and Tribology. Springer, Cham. https://doi.org/10.1007/978-3-319-76075-9_6
Download citation
DOI: https://doi.org/10.1007/978-3-319-76075-9_6
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-76074-2
Online ISBN: 978-3-319-76075-9
eBook Packages: EngineeringEngineering (R0)