Abstract
The technology of bending–rolling in rollers of shaped aircraft parts is proposed and implemented by the pilot straightening–bending installation in AO Ulyanovsk NIAT. Experimental results are presented for research of longitudinal bending of aircraft part blanks made of formed sections. The data obtained demonstrates the possibility of obtaining the workpieces with a radius of curvature less than 600 mm from high-strength aluminum alloys while preserving the profile cross-section parameters.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
Markovtsev, V.A., Baranov, A.S., Ilyushkin, M.V., and Popov, A.G., Manufacture of Frames and Stringers with Lengthwise Curvature from Formed Sections, Aviatsionnaya Promyshlennost’, 2013, no. 3, pp. 32–34.
Markovtsev, V.A., RU Patent 2564798, Byul. Izobr., 2015, no. 28.
Zakirov, I.M., Bodunov, N.M., Druzhinin, G.V., Ružicka, K., Use of the Numerical Method for Calculating Parameters of Thin-Walled Part Bending by Elastic Medium, Iz. Vuz. Av. Tekhnika, 2001, vol. 44, no. 2, pp. 58–62 [Russian Aeronautics (Engl. Transl.), vol. 44, no. 2, pp. 83–89].
Bodunov, N.M., Calculation of Setup Variables for the Process of Bending and Rolling Thin-Walled Components using the Finite Difference Method, Iz. Vuz. Av. Tekhnika, 2011, vol. 54, no. 1, pp. 64–67 [Russian Aeronautics (Engl. Transl.), vol. 44, no. 2, pp. 89–94].
Sharov, A.A., Barvinok, V.A., Komarov, A.D., Gromova, E.G., Es’kina, E.V., and Kulakov, V.G., Research of Process of the Straitened Bend of Sheet Purveyances by an Elastic Environment, Izvestiya Samarskogo Nauchnogo Tsentra Rossiiskoi Akademii Nauk, 2011, vol. 13, no. 4–2, pp. 531–536.
Kutin, A.A. and Turkin, M.V., Technological Equipment for Flexible Production Systems of New Generation, Vestnik MGTU “Stankin”, 2011, no. 3 (15), pp. 36–40.
Proskuryakov, G.V., Research of Cramped Bend, Cand. Sc. (Tech.) Dissertation, Khar’kov, 1966.
Markovtsev, V.A., Ilyushkin, M.V., and Popov, A.G., Calculation of Technological Modes of Longitudinal Roll Forming of Thin-Walled Sheet Sections, Aviatsionnaya Promyshlennost’, 2016, no. 1, pp. 33–37.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Aviatsionnaya Tekhnika, 2020, No. 4, pp. 201 - 203.
About this article
Cite this article
Markovtsev, V.A., Baranov, A.S., Popov, A.G. et al. Improvement of Technologies for Longitudinal Bending and Straightening of Shaped Aircraft Parts. Russ. Aeronaut. 63, 781–783 (2020). https://doi.org/10.3103/S1068799820040297
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068799820040297