Skip to main content
SpringerLink
Log in

Cutting of Special Stainless Steel Thrust-Bearing Components

  • Published:
Russian Engineering Research Aims and scope

Abstract

The cutting of special stainless steels for thrust bearings is studied experimentally. The steels considered are 95Х18-Ш, 110Х18-ШД, 75ХГСФ, and 40ХНЮ-ВИ. The formation of the surface roughness and the distortion of the part after machining are described. The influence of the cutting parameters on the cutting force and temperature in the machining zone is determined. Experiments are conducted to determine the roughness of the machined surface and the distortion of the samples in various cutting conditions. The results provide the basis for technological recommendations.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.

REFERENCES

  1. Vinarskii, M.S. and Lur’e, M.V., Planirovanie eksperimenta v tekhnologicheskikh issledovaniyakh (Planning the Experiment in Technological Research), Kiev: Tekhnika, 1975.

  2. Kuznetsov, V.A., Synthesis and study of technological structures of methods for machining surfaces of machine parts, Doctoral (Eng.) Dissertation, Moscow, 2000.

  3. Golobokov, A.V., Volkov, R.B., Cherepakhin, A.A., and Kuznetsov, V.A., New medium steel premium for parts of rolling bearings, Zagotov. Proizvod. Mashinostr., 2014, no. 5, pp. 29–32.

  4. Konovalov, V.V., Increasing the productivity of turning bearing rings by determining rational cutting modes based on the identification of the transfer function of the dynamic system by vibroacoustic vibrations, Cand. Sci. (Eng.) Dissertation, Saratov, 2012.

  5. Volkov, R.B., Golobokov, A.V., Kuznetsov, V.A., and Cherepakhin, A.A., Analysis of machinability of steel 75HGFC, Izv. Mosk. Gos. Tekh. Univ. MAMI, 2012, vol. 2, no. 2 (14), pp. 51–55.

  6. Volkov, R.B., Wear of multifaceted perishable carbide inserts in turning of experimental steel 75HGFC, Izv. Mosk. Gos. Tekh. Univ. MAMI, 2014, vol. 2, no. 1 (19), pp. 69–73.

Download references

Author information

Authors and Affiliations

  1. OK LOZA, Loza, Moscow Region, Russia

    R. B. Volkov

  2. STANKIN Moscow State Technical University, Moscow, Russia

    V. A. Kuznetsov

  3. Moscow Polytechnic University, Moscow, Russia

    A. Yu. Prokop’ev

Authors
  1. R. B. Volkov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. V. A. Kuznetsov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. Yu. Prokop’ev
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to R. B. Volkov, V. A. Kuznetsov or A. Yu. Prokop’ev.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Volkov, R.B., Kuznetsov, V.A. & Prokop’ev, A.Y. Cutting of Special Stainless Steel Thrust-Bearing Components. Russ. Engin. Res. 43, 376–378 (2023). https://doi.org/10.3103/S1068798X23040342

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X23040342

Keywords:

Search

Navigation