Abstract
In this work, the analysis of relationships between cutting tool properties and machining parameters and conditions in high speed multi-axis milling has been reported. The analysis is based on the review of the best existing cutting mechanisms and shaping schemes.
This is a preview of subscription content, log in via an institution to check access.
REFERENCES
Grechishnikov, V.A., Modelirovanie sistem instrumental’nogo obespecheniya avtomatizirovannykh proizvodstv (Modeling of the Systems of Tool Support of Automated Industries), Moscow: Mashinostroenie, 1988.
Grigoriev, S.N., Grechishnikov, V.A., Volosova, M.A., et al., Investigation of technological parameters for machining toroidal section of solid ceramic end mills, IOP Conf. Ser.: Mater. Sci. Eng., 2020, vol. 971, no. 2, p. 022065. https://doi.org/10.1088/1757-899X/971/2/022065
Pivkin, P.M., Nadykto, A.B., Grechishnikov, V.A., Volosova, M.A., Minin, I.V., and Grigoriev, S.N., A new method for modeling edges of a toroidal cutting surface of solid ceramic end mills, Proc. SPIE, 2020, vol. 11540, p. 115401G. https://doi.org/10.1117/12.2574391
Grechishnikov, V.A., Petukhov, Yu.E., Pivkin, P.M., et al., Trochoidal slot milling, Russ. Eng. Res., 2017, vol. 37, no. 9, pp. 821–823. https://doi.org/10.3103/S1068798X17090106
Grigoriev, S.N., Volosova, M.A., Zelensky, A.A., et al., WEDM as a replacement for grinding in machining ceramic Al2O3-TiC cutting inserts, Metals, 2021, vol. 11, no. 6, p. 882.
Pivkin, P.M., Grechishnikov, V.A., Ershov, A.A., and Grigoriev, S.N., A new method definition of cutting surface of drills by image processing flank surface, Proc. SPIE, 2021, vol. 11914, p. 1191413. https://doi.org/10.1117/12.2605834
Grigoriev, S.N., Volosova, M.A., Fedorov, S.V., et al., Development of DLC-coated solid SiAlON/TiN ceramic end mills for nickel alloy machining: Problems and prospects, Coatings, 2021, vol. 11, no. 5, p. 532.
Pivkin, P.M., Grechishnikov, V.A., Ershov, A.A., and Nadykto, A.B., A new method for the precise determination of rational geometric parameters of the helical groove and cutting part of high-performance triflute, Proc. SPIE, 2020, vol. 11540, p. 1154014. https://doi.org/10.1117/12.2574392
Grigor’ev, S.N., Solving problems of technological reequipment of mechanical engineering, Instrum. Tekhnol. Oborud., 2008, no. 10, pp. 14–18.
Voronov, S.A., Kiselev, I.A., and Arshinov, S.V., Methodology for the application of numerical simulation of the dynamics of multi-axis milling of complex profile parts in the design of the technological process, Vestn. Mosk. Gos. Tekh. Univ. im. N.E. Baumana. Ser. Mashinostr., 2012, no. S6, pp. 50–69.
Grechishnikov, V.A., Improvement of tooling support for machine-building production, Vestn. Mosk. Gos. Tekhnol. Univ. “Stankin”, 2008, no. 1, pp. 13–18.
ACKNOWLEDGMENTS
This research was conducted on equipment at the State Engineering Center of STANKIN Moscow Technological University.
Funding
Financial support was provided by the Russian Science Fund (project 22-79-10353).
Author information
Authors and Affiliations
Corresponding authors
Additional information
Translated by B. Gilbert
About this article
Cite this article
Grechishnikov, V.A., Pivkin, P.M., Petukhov, Y.E. et al. Analysis of Relationships between Cutting Tool Properties, Machining Parameters and Product Quality in High Speed Multi-Axis Milling. Russ. Engin. Res. 43, 369–372 (2023). https://doi.org/10.3103/S1068798X23040159
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X23040159