Skip to main content
SpringerLink
Log in

Wire-Cut Electric Discharge Machining of Curved Polymer-Composite Surfaces

  • Published:
Russian Engineering Research Aims and scope

Abstract

Stacked wire-cut electric discharge machining (EDM) of curved polymer-composite surfaces is considered. After studying various stack configurations, a productive method of machining polymer composite is proposed: the most effective stack consists of three workpieces with alternating conducting layers. This method permits stable machining without wire fracture and produces the specified curved surface contour of a polymer-composite workpiece, at a rate of 0.5 mm/min. That expands the scope for the manufacture of polymer-composite products. Wire-cut electric discharge machining may be used in production conditions to cut stacks of polymer-composite workpieces.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.

Similar content being viewed by others

REFERENCES

  1. Ablyaz, T.R., Shlykov, E.S., Muratov, K.R., and Sidhu, S.S., Analysis of wire-cut electro discharge machining of polymer composite materials, Micromachines, 2021, vol. 12, art. ID 571.

    Article  Google Scholar 

  2. Ablyaz, T.R., Muratov, K.R., Shlykov, E.S., et al., Electric-discharge machining of polymer composites, Russ. Eng. Res., 2019, vol. 39, no. 10, pp. 898–900.

    Article  Google Scholar 

  3. Hsue, W.J., Fundamental geometry analysis of wire electrical discharge machining in corner cutting, Int. J. Mach. Tools Manuf., 1999, vol. 39, pp. 651–667.

    Article  Google Scholar 

  4. Han, F., Zhang, J., and Soichiro, I., Corner error simulation of rough cutting in wire EDM, Precis. Eng., 2007, vol. 31, pp. 331–336.

    Article  Google Scholar 

  5. Altpeter, F. and Perez, R., Relevant topics in wire electrical discharge machining control, J. Mater. Process. Technol., 2004, vol. 149, pp. 147–151.

    Article  Google Scholar 

Download references

Funding

Financial support was provided by the Russian President in encouragement of young scientists (grant MK-566.2021.4).

Author information

Authors and Affiliations

  1. Perm National Research Polytechnic University, Perm, Russia

    E. S. Shlykov, T. R. Ablyaz, V. V. Shiryaev & K. R. Muratov

Authors
  1. E. S. Shlykov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. R. Ablyaz
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. V. V. Shiryaev
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. K. R. Muratov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to E. S. Shlykov, T. R. Ablyaz, V. V. Shiryaev or K. R. Muratov.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Shlykov, E.S., Ablyaz, T.R., Shiryaev, V.V. et al. Wire-Cut Electric Discharge Machining of Curved Polymer-Composite Surfaces. Russ. Engin. Res. 42, 853–854 (2022). https://doi.org/10.3103/S1068798X22080238

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X22080238

Keywords:

Search

Navigation