Skip to main content
SpringerLink
Log in

Influence of Setup and Kinematic Parameters on the Shape Precision of Workpieces

  • Published:
Russian Engineering Research Aims and scope

Abstract

The influence of the setup parameters in the lapping of external cylindrical precision surfaces by rolling is compared. With 180° rotation of the parts in the separator slots and halving of the machining time, the initial geometric error of the slides is ensured, and the required shape is consistently obtained, to within 0.002 mm.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.

Similar content being viewed by others

REFERENCES

  1. Yuan, J., Yao, W., Zhao, P., et al., Kinematics and trajectory of both-sides cylindrical lapping process in planetary motion type, Int. J. Mach. Tools Manuf., 2015, vol. 92, pp. 60–71.

    Article  Google Scholar 

  2. Orlov, P.N., Tekhnologicheskoe obespechenie kachestva detalei metodami dovodki (Technological Quality Assurance of Parts by Finishing Methods), Moscow: Mashinostroenie, 1988.

  3. Kremen’, Z.I. and Pavlyuchuk, A.I., Abrazivnaya dovodka (Abrasive Finishing), Moscow: Mashinostroenie, 1967.

  4. Muratov, K.R. and Makarov, V.F., Equipment analysis for finishing abrasive processing of flat precision surfaces of products, Vestn. Permsk. Nats. Issled. Politekh. Univ. Mashinostr., Materialoved., 2017, vol. 19, no. 1, pp. 170–186.

    Google Scholar 

  5. Su, J., Yuan, J., Zhang, S., and Lv, B., Optimization experiment on eccentric lapping of cylindrical rollers, Natotechnol. Precis. Eng., 2018, vol. 1, pp. 197–204.

    Article  Google Scholar 

  6. Muratov, K.R., Ablyaz, T.R., Gashev, E.A., and Rykunov, A.N., Software for simulating the surface wear of tools, Russ. Eng. Res., 2019, vol. 39, no. 10, pp. 869–871. https://doi.org/10.3103/S1068798X19100174

    Article  Google Scholar 

Download references

Funding

Financial support was provided by the Russian Ministry of Science and Higher Education (project FSNM-2020-0028).

Author information

Authors and Affiliations

  1. Perm National Research Polytechnic University, Perm, Russia

    K. R. Muratov, T. R. Ablyaz & E. A. Gashev

  2. Almetyevsk State Oil Institute, Almetyevsk, Tatarstan, Russia

    A. A. D’yakonov

Authors
  1. K. R. Muratov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. R. Ablyaz
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. A. D’yakonov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. E. A. Gashev
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to K. R. Muratov or A. A. D’yakonov.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Muratov, K.R., Ablyaz, T.R., D’yakonov, A.A. et al. Influence of Setup and Kinematic Parameters on the Shape Precision of Workpieces. Russ. Engin. Res. 42, 823–825 (2022). https://doi.org/10.3103/S1068798X22080160

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X22080160

Keywords:

Search

Navigation